Home › Drivetrain › AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2015.08
RM2660E _52 Drivetrain _052807 AE80F AUTOMATIC TRANSMISSION / TRANSAXLE _0255308 AUTOMATIC TRANSMISSION SYSTEM J

AE80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  Pattern Select Switch Power Mode Circuit  


DESCRIPTION

The TCM memory contains the programs for the normal and power shift patterns.

By following the programs corresponding to the signals from the PWR switch (integration control and panel assembly), the park/neutral position switch and other various sensors, the TCM switches the shift solenoid valves on and off, and controls the transmission gear change operation.

WIRING DIAGRAM

C343215E02
5.917,3.999 6.286,4.169 0.369,0.170 10 A38 5.917,4.152 6.339,4.347 0.422,0.195 10 ECM 2.851,3.817 3.273,4.013 0.422,0.195 10 TCM 0.527,4.391 2.593,4.586 2.066,0.195 10 : CAN Communication Line 1.815,2.143 2.339,2.339 0.524,0.195 10 V9 1.815,2.322 4.390,2.658 2.575,0.336 10 Integration Control and Panel Assembly 3.521,0.694 3.666,0.889 0.144,0.195 10 P 3.345,1.63 3.667,1.825 0.323,0.195 10 2ND 2.382,1.63 2.527,1.825 0.144,0.195 10 E 3.712,0.694 3.898,0.889 0.186,0.195 10 6 3.712,1.63 3.898,1.825 0.186,0.195 10 8 2.188,1.63 2.395,1.825 0.207,0.195 10 5 5.214,0.694 5.543,0.889 0.330,0.195 10 13 5.51,0.694 5.914,0.889 0.404,0.195 10 PWR 6.372,0.497 6.776,0.692 0.404,0.195 10 12 V 6.372,1.431 6.776,1.626 0.404,0.195 10 12 V 5.214,1.63 5.580,1.825 0.367,0.195 10 12 5.51,1.63 5.970,1.825 0.459,0.195 10 SNWI

PROCEDURE

1.INSPECT PWR SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY)
a.
C331266E28
2.156,1.458 2.688,1.583 false 0.75,0.969 1.281,1.083 false 0.125,0.052 0.406,0.229 0.281,0.177 10 false *a 2.75,1.51 2.979,1.698 0.229,0.188 10 false P 0.594,0.865 0.823,1.052 0.229,0.188 10 false E

Remove the integration control and panel assembly (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>COMBINATION SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (P) - 5 (E) PWR switch on Below 1 Ω
6 (P) - 5 (E) PWR switch off 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Integration Control and Panel Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL AND PANEL ASSEMBLY - BODY GROUND)

NG

REPLACE INTEGRATION CONTROL AND PANEL ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL AND PANEL ASSEMBLY - BODY GROUND)
a.
U165556E02
2.604,0.708 2.021,0.99 true 0.125,0.052 0.406,0.229 0.281,0.177 10 false *a 2.667,0.573 2.875,0.76 0.208,0.188 10 false E 0.521,0.844 0.875,1.021 0.354,0.177 10 false V9

Disconnect the integration control and panel assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V9-5 (E) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Integration Control and Panel Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL AND PANEL ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL AND PANEL ASSEMBLY - ECM)
a.
U156201E03
1.896,0.917 1.542,1.75 false 0.125,0.063 0.406,0.24 0.281,0.177 10 false *a 1.229,1.771 2,1.958 0.771,0.188 10 false 13 (PWR) 1.667,0.271 2.021,0.448 0.354,0.177 10 false A38

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A38-13 (PWR) - Body ground PWR switch on Below 1 Ω
A38-13 (PWR) - Body ground PWR switch off 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR