Home › Drivetrain › AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2015.08
RM2660E _52 Drivetrain _052807 AE80F AUTOMATIC TRANSMISSION / TRANSAXLE _0255308 AUTOMATIC TRANSMISSION SYSTEM C

AE80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P08D2  Shift Solenoid "J" Control Circuit Low  P08D3  Shift Solenoid "J" Control Circuit High  


DESCRIPTION

Based on the ON-OFF combinations of the shift solenoid valve SL1, SL2, SL3, SL4, SL5, SC1 and SC2, the TCM performs gear shifts from 1st gear to 8th gear.

If a circuit related to a solenoid valve is open or shorted, the TCM uses the fail-safe function to turn other solenoid valves on or off. If all solenoid valves are malfunctioning, only the mechanical fluid pressure circuit will function and some manual operation will be possible. If an open or short has occurred, the TCM cuts power to the malfunctioning solenoid valve.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P08D2
1.

Shift solenoid valve SC2 is operated

2.

Shift solenoid valve SC2 terminal voltage level is low

3.

0.5 seconds

4.

1-trip detection logic


·

Shift solenoid valve SC2

·

Transmission wire

·

Harness and connector

·

TCM


P08D3
1.

Shift solenoid valve SC2 is not operated

2.

Shift solenoid valve SC2 terminal voltage level is high

3.

0.5 seconds

4.

1-trip detection logic


·

Shift solenoid valve SC2

·

Transmission wire

·

Harness and connector

·

TCM



MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve SC2 circuit. When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem, illuminates the MIL and stores the DTC. When the shift solenoid valve SC2 is ON, if its resistance is 8 Ω or less, the TCM determines there is a short in the shift solenoid valve SC2 circuit.

When the shift solenoid valve SC2 is OFF, if its resistance is 100 kΩ or higher, the TCM determines there is an open in the shift solenoid valve SC2 circuit.

WIRING DIAGRAM

C343213E03
5.19,1.066 5.698,1.269 0.508,0.204 10 SC2 4.906,1.066 5.413,1.269 0.508,0.204 10 28 3.618,1.066 4.126,1.269 0.508,0.204 10 8 3.202,1.066 3.710,1.269 0.508,0.204 10 SC2 1.485,1.672 3.187,1.876 1.702,0.204 10 Shift Solenoid Valve SC2 1.585,2.644 2.093,2.848 0.507,0.204 10 C171 1.585,2.832 3.204,3.036 1.619,0.204 10 Transmission Wire 5.569,3.09 6.076,3.294 0.507,0.204 10 TCM 5.569,2.902 6.076,3.105 0.507,0.204 10 A80

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION).


HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SHIFT SOLENOID VALVE SC2 - TCM)
a.
U165635E02
0.75,2.083 0.396,2.938 false 0.125,0.052 0.406,0.229 0.281,0.177 10 false *a 0.094,3.01 0.865,3.198 0.771,0.188 10 false 28 (SC2) 0.865,0.177 1.219,0.354 0.354,0.177 10 false A80

Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A80-28 (SC2) - Body ground 20°C (68°F) 11 to 15 Ω


Text in Illustration
*a Rear view of wire harness connector
(to TCM)



OK

NG

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.

Disconnect the C171 transmission wire connector.


b.

Disconnect the A80 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C171-8 (SC2) - A80-28 (SC2) Always Below 1 Ω
C171-8 (SC2) or A80-28 (SC2) - Body ground Always 10 kΩ or higher




OK

3.INSPECT SHIFT SOLENOID VALVE SC2

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SC2
a.
C342510E01
0.122,0.053 0.383,0.245 0.261,0.192 10 *1 2.87,0.032 3.192,0.224 0.322,0.192 10 (+) 2.055,0.032 2.377,0.224 0.322,0.192 10 (-)

Remove the shift solenoid valve SC2 (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve SC2 connector - Shift solenoid valve SC2 body 20°C (68°F) 11 to 15 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Shift solenoid valve SC2 connector

·

Battery negative (-) → Shift solenoid valve SC2 body


Valve moves and makes an operating noise



Text in Illustration
*1 Shift Solenoid Valve SC2


OK

NG