Home › Drivetrain › AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2015.08
RM2660E _52 Drivetrain _052807 AE80F AUTOMATIC TRANSMISSION / TRANSAXLE _0255308 AUTOMATIC TRANSMISSION SYSTEM C

AE80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0798  Pressure Control Solenoid "C" Electrical  


DESCRIPTION

Based on the ON-OFF combinations of the shift solenoid valve SL1, SL2, SL3, SL4 and SL5, the TCM performs gear shifts from 1st gear to 8th gear.

If a circuit related to a solenoid valve is open or shorted, the TCM uses the fail-safe function to turn other solenoid valves ON or OFF. If all solenoid valves are malfunctioning, only the mechanical fluid pressure circuit will function and some manual operation will be possible. If an open or short has occurred, the TCM cuts power to the malfunctioning solenoid valve.

HINT:

The following table shows normal operation of the shift solenoid valve SL3 when the shift lever is in D.

Shift Solenoid Valve Operation:
Gear 1st 2nd 3rd 4th 5th 6th 7th 8th
Shift Solenoid Valve SL3 ON ON OFF ON ON ON OFF ON


DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P0798
1.

Driving so that gear changes occur

2.

Shift solenoid valve SL3 circuit is open or shorted

3.

2 seconds

4.

1-trip detection logic


·

Shift solenoid valve SL3

·

Transmission wire

·

Harness or connector

·

TCM



MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SL3 circuit. The TCM commands gear shifts by turning the shift solenoid valves on or off. When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem, illuminates the MIL and stores a DTC. The TCM performs the fail-safe function and turns the other normal shift solenoid valves on or off. In case of an open or short circuit, the TCM stops sending current to the open or short circuited solenoid.

WIRING DIAGRAM

C343212E24
5.188,1.125 5.698,1.333 0.51,0.208 10 false SL3+ 3.479,1.146 3.99,1.354 0.51,0.208 10 false SL3+ 1.094,1.313 1.271,1.521 0.177,0.208 10 false 2 1.073,2.125 1.281,2.313 0.208,0.188 10 false 1 4.927,1.135 5.292,1.344 0.365,0.208 10 false 16 3.896,1.135 4.156,1.365 0.26,0.229 10 false 23 5.188,2.073 5.698,2.281 0.51,0.208 10 false SL3- 5.615,3.042 6.125,3.25 0.51,0.208 10 false A81 5.615,3.24 6.125,3.448 0.51,0.208 10 false TCM 3.51,2.104 3.917,2.323 0.406,0.219 10 false SL3- 1.469,1.719 3.281,1.927 1.813,0.208 10 false Shift Solenoid Valve SL3 4.958,2.063 5.469,2.271 0.51,0.208 10 false 6 3.906,2.083 4.156,2.313 0.25,0.229 10 false 24 1.74,2.688 2.25,2.896 0.51,0.208 10 false C171 1.74,2.875 3.073,3.083 1.333,0.208 10 false Transmission Wire

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION).


HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SHIFT SOLENOID VALVE SL3 - TCM)
a.
U165641E02
1.49,1.927 2.01,2.917 false 1.458,2 0.979,2.917 false 0.125,0.052 0.406,0.229 0.281,0.177 10 false *a 1.771,2.927 2.542,3.115 0.771,0.188 10 false 6 (SL3-) 0.583,2.906 1.323,3.094 0.74,0.188 10 false 16 (SL3+) 1.594,0.167 1.948,0.344 0.354,0.177 10 false A81

Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A81-16 (SL3+) - A81-6 (SL3-) 20°C (68°F) 5.0 to 5.6 Ω
A81-16 (SL3+) or A81-6 (SL3-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to TCM)



OK

NG

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.

Disconnect the C171 transmission wire connector.


b.

Disconnect the A81 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C171-23 (SL3+) - A81-16 (SL3+) Always Below 1 Ω
C171-24 (SL3-) - A81-6 (SL3-) Always Below 1 Ω
C171-23 (SL3+) or A81-16 (SL3+) - Body ground Always 10 kΩ or higher
C171-24 (SL3-) or A81-6 (SL3-) - Body ground Always 10 kΩ or higher




OK

3.INSPECT SHIFT SOLENOID VALVE SL3

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SL3
a.
C209928E13
0.057,0.005 0.374,0.207 0.317,0.202 10 *a 1.757,0.949 2.207,0.361 false 2.238,0.194 2.402,0.396 0.164,0.202 10 1 1.506,0.949 1.056,0.361 false 0.918,0.194 1.082,0.396 0.164,0.202 10 2 1.757,2.945 2.207,2.358 false 2.238,2.191 2.402,2.393 0.164,0.202 10 1 1.506,2.945 1.056,2.358 false 0.918,2.191 1.082,2.393 0.164,0.202 10 2 1.923,3.928 2.122,4.130 0.200,0.202 10 (-) 1.119,3.928 1.339,4.130 0.221,0.202 10 (+)

Remove the shift solenoid valve SL3 (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 1 of the shift solenoid valve SL3 - Terminal 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 2

·

Battery negative (-) → Terminal 1


Valve moves and makes an operating noise



Text in Illustration
*1 Shift Solenoid Valves SL3


OK

NG