Based on the ON-OFF combinations of the shift solenoid valve SL1, SL2, SL3, SL4 and SL5, the TCM performs gear shifts from 1st gear to 8th gear.
If a circuit related to a solenoid valve is open or shorted, the TCM uses the fail-safe function to turn other solenoid valves ON or OFF. If all solenoid valves are malfunctioning, only the mechanical fluid pressure circuit will function and some manual operation will be possible. If an open or short has occurred, the TCM cuts power to the malfunctioning solenoid valve.
The following table shows normal operation of the shift solenoid valve SL4 when the shift lever is in D.
| Gear | 1st | 2nd | 3rd | 4th | 5th | 6th | 7th | 8th |
| Shift Solenoid Valve SL4 | OFF | OFF | OFF | ON | OFF | ON | OFF | OFF |
| DTC No. | DTC Detection Condition
1.
Diagnosis Condition 2.
Malfunction Status 3.
Malfunction Time 4.
Other |
Trouble Area |
|---|---|---|
| P2810 | 1.
Driving so that gear changes occur 2.
Shift solenoid valve SL4 circuit is open or shorted 3.
2 seconds 4.
1-trip detection logic |
·
Shift solenoid valve SL4 ·
Transmission wire ·
Harness or connector ·
TCM |
This DTC indicates an open or short in the shift solenoid valve SL4 circuit. The TCM commands gear shifts by turning the shift solenoid valves on or off. When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem, illuminates the MIL and stores a DTC. The TCM performs the fail-safe function and turns the other normal shift solenoid valves on or off. In case of an open or short circuit, the TCM stops sending current to the open or short circuited solenoid.
Perform registration and/or initialization when parts related to the automatic transmission are replaced (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION).
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Perform the D Position Shift Test in Road Test (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>ROAD TEST).
Check for DTCs again (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).
Disconnect the TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A81-14 (SL4+) - A81-5 (SL4-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| A81-14 (SL4+) or A81-5 (SL4-) - Body ground | Always | 10 kΩ or higher |
| *a | Rear view of wire harness connector
(to TCM) |
OK
NG
Disconnect the C171 transmission wire connector.
Disconnect the A81 TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C171-13 (SL4+) - A81-14 (SL4+) | Always | Below 1 Ω |
| C171-14 (SL4-) - A81-5 (SL4-) | Always | Below 1 Ω |
| C171-13 (SL4+) or A81-14 (SL4+) - Body ground | Always | 10 kΩ or higher |
| C171-14 (SL4-) or A81-5 (SL4-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the shift solenoid valve SL4 (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Terminal 1 of the shift solenoid valve SL4 - Terminal 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) with a 21 W bulb → Terminal 2 ·
Battery negative (-) → Terminal 1 |
Valve moves and makes an operating noise |
| *1 | Shift Solenoid Valves SL4 |
OK
NG