Home › Drivetrain › CLUTCH › CLUTCH UNIT(for 1GR-FE)
RM2660E _52 Drivetrain _052808 CLUTCH _0255316 CLUTCH UNIT(for 1GR-FE) G

CLUTCH  CLUTCH UNIT(for 1GR-FE)  INSPECTION  


PROCEDURE

Hide 31250 1.INSPECT CLUTCH DISC ASSEMBLY

NOTICE:

When replacing the clutch disc assembly, make sure to perform an inspection of the flywheel sub-assembly and clutch cover assembly.


a.
C173305

Using a vernier caliper, measure the rivet depth.

Minimum Rivet Depth:

0.3 mm (0.0118 in.)


If the depth is less than the minimum, replace the clutch disc assembly.


b.
C114037

Using a dial indicator with a roller instrument, check the clutch disc runout.

Maximum Runout:

0.9 mm (0.0354 in.)


If the runout is more than the maximum, replace the clutch disc assembly.


Hide 31210 2.INSPECT CLUTCH COVER ASSEMBLY

C173310E03
0.677,1.042 1.094,1.208 0.417,0.167 10 false Depth 0.656,0.417 1.198,0.583 0.542,0.167 10 false Width

a.

Using a vernier caliper, inspect the depth and width of wear of the diaphragm spring.

Maximum Wear:
Depth Width
0.6 mm (0.0236 in.) 5.0 mm (0.197 in.)


If the wear is more than the maximum, replace the clutch cover assembly.


b.
A272260E03
1.833,0.479 2.938,0.479 true 1.833,1.698 2.938,1.698 true 2.958,0.385 3.156,0.552 0.198,0.167 10 false *a 2.958,1.615 3.156,1.781 0.198,0.167 10 false *b

Perform a visual inspection of the clutch cover assembly.

i.

Inspect for hair cracks or scratches extending from the center outwards, or discoloration.


ii.

Inspect for hair cracks in a circular pattern, discoloration or excessive wear.

Text in Illustration
*1 Hair cracks, scratches or discoloration
*2 Hair cracks, discoloration or excessive wear

If there is any damage, replace the clutch cover assembly.



Hide 13405 3.INSPECT FLYWHEEL SUB-ASSEMBLY

C173313

a.

Using a dial indicator, inspect the flywheel runout.

Maximum Runout:

0.1 mm (0.00393 in.)


If the runout is more than the maximum, replace the flywheel sub-assembly.


b.
A272261E03
2.208,0.479 2.979,0.479 true 1.917,1.573 2.854,1.573 true 3.021,0.375 3.219,0.542 0.198,0.167 10 false *a 2.917,1.49 3.115,1.656 0.198,0.167 10 false *b

Perform a visual inspection of the flywheel sub-assembly.

i.

Inspect for hair cracks or scratches extending from the center outwards, or discoloration.


ii.

Inspect for hair cracks in a circular pattern, discoloration or excessive wear.

Text in Illustration
*1 Hair cracks, scratches or discoloration
*2 Hair cracks, discoloration or excessive wear

If there is any damage, replace the flywheel sub-assembly.



Hide 31230 4.INSPECT CLUTCH RELEASE BEARING ASSEMBLY

F050790

a.

Check that the clutch release bearing moves smoothly without abnormal resistance by turning the sliding parts of the clutch release bearing (contact surfaces with the clutch cover) while applying force in the axial direction.


b.

Inspect the clutch release bearing for damage or wear.

Replace the release bearing assembly as necessary.


Hide 33311W 5.INSPECT INPUT SHAFT BEARING

Q002481

a.

Turn the bearing by hand while applying force in the direction of the rotation.

If the bearing is stuck or difficult to turn, replace the input shaft bearing.

HINT:

The bearing is permanently lubricated and requires no cleaning or lubrication.



Hide 33311W 6.REPLACE INPUT SHAFT BEARING

C173312E02
1.854,0.823 2.344,0.51 true 2.344,0.51 2.552,0.51 false 2.646,0.438 3.042,0.635 0.396,0.198 10 false SST

a.

Using SST, remove the bearing.

SST
09303-35011  


b.
C173311E02
1.656,0.896 2.198,0.469 true 2.208,0.469 2.458,0.469 false 2.542,0.396 2.906,0.573 0.365,0.177 10 false SST

Using SST and a hammer, install a new bearing.

SST
09304-12012  

HINT:

After installing the input shaft bearing to the engine side, make sure that it rotates smoothly.