33333
1.INSPECT 3RD GEAR THRUST CLEARANCE
Using a feeler gauge, measure the 3rd gear thrust clearance.
0.10 to 0.45 mm (0.00394 to 0.0177 in.)
If the clearance is outside the specification, replace the defective gear, spacer or shaft.
33336
2.INSPECT 5TH GEAR THRUST CLEARANCE
Using a feeler gauge, measure the 5th gear thrust clearance.
0.10 to 0.35 mm (0.00394 to 0.0137 in.)
If the clearance is outside the specification, replace the defective gear, spacer or shaft.
33332
3.INSPECT 2ND GEAR THRUST CLEARANCE
Using a feeler gauge, measure the 2nd gear thrust clearance.
0.10 to 0.35 mm (0.00394 to 0.0137 in.)
If the clearance is outside the specification, replace the defective gear, spacer or shaft.
33335
4.INSPECT 1ST GEAR THRUST CLEARANCE
Using a feeler gauge, measure the 1st gear thrust clearance.
0.10 to 0.45 mm (0.00394 to 0.0177 in.)
If the clearance is outside the specification, replace the defective gear, spacer or shaft.
33333
5.INSPECT 3RD GEAR RADIAL CLEARANCE
Using a dial indicator, measure the 3rd gear radial clearance.
0.020 to 0.073 mm (0.000788 to 0.00287 in.)
If the clearance is outside the specification, replace the defective gear, needle roller bearing or shaft.
33336
6.INSPECT 5TH GEAR RADIAL CLEARANCE
Using a dial indicator, measure the 5th gear radial clearance.
0.015 to 0.068 mm (0.000591 to 0.00267 in.)
If the clearance is outside the specification, replace the defective gear, needle roller bearing or shaft.
33332
7.INSPECT 2ND GEAR RADIAL CLEARANCE
Using a dial indicator, measure the 2nd gear radial clearance.
0.015 to 0.068 mm (0.000591 to 0.00267 in.)
If the clearance is outside the specification, replace the defective gear, needle roller bearing or shaft.
33335
8.INSPECT 1ST GEAR RADIAL CLEARANCE
Using a dial indicator, measure the 1st gear radial clearance.
0.020 to 0.073 mm (0.000788 to 0.00287 in.)
If the clearance is outside the specification, replace the defective gear, needle roller bearing or shaft.
33331B
9.REMOVE REVERSE GEAR SNAP RING
Using 2 screwdrivers and a hammer, tap out the snap ring.
Use a piece of cloth to prevent the snap ring from flying off.
33335
10.REMOVE 1ST GEAR
Shift the No. 1 transmission hub sleeve to the 2nd gear.
Using SST and a press, remove the bearing, 1st gear and synchronizer ring.
33335C
11.REMOVE 1ST GEAR NEEDLE ROLLER BEARING
Remove the 1st gear needle roller bearing from the output shaft.
33037B
12.REMOVE NO. 1 SYNCHRONIZER RING SET
Remove the No. 1 synchronizer ring from the 1st gear.
33361B
13.REMOVE NO. 1 CLUTCH HUB SHAFT SNAP RING
Using 2 screwdrivers and a hammer, tap out the snap ring.
Use a piece of cloth to prevent the snap ring from flying off.
33332
14.REMOVE 2ND GEAR
Using a press, remove the 2nd gear and synchronizer ring.
33332B
15.REMOVE 2ND GEAR NEEDLE ROLLER BEARING
Remove the 2nd gear needle roller bearing from the output shaft.
33038E
16.REMOVE NO. 2 SYNCHRONIZER RING SET
Remove the No. 2 synchronizer ring set from the 2nd gear.
33363
17.REMOVE NO. 1 TRANSMISSION HUB SLEEVE
Remove the No. 1 transmission hub sleeve, 3 shifting keys and 2 springs from the No. 1 transmission clutch hub.
Use a piece of cloth to prevent the spring from flying off.
33362A
18.REMOVE NO. 2 CLUTCH HUB SETTING SHAFT SNAP RING
Using 2 screwdrivers and a hammer, tap out the snap ring.
Use a piece of cloth to prevent the snap ring from flying off.
33333
19.REMOVE 3RD GEAR
Shift the No. 3 transmission hub sleeve to the 5th gear.
Using SST and a press, remove the 3rd gear and synchronizer ring.
33333A
20.REMOVE 3RD GEAR NEEDLE ROLLER BEARING
Remove the 3rd gear needle roller bearing from the output shaft.
33039
21.REMOVE NO. 3 SYNCHRONIZER RING SET
Remove the No. 3 synchronizer ring set from the 3rd gear.
36235B
22.REMOVE NO. 2 TRANSMISSION HUB SLEEVE
Remove the No. 2 transmission hub sleeve, 3 shifting keys and 2 springs from the No. 2 transmission clutch hub.
Use a piece of cloth to prevent the spring from flying off.
33393A
23.REMOVE NO. 3 TRANSMISSION CLUTCH HUB SHAFT SNAP RING
Using 2 screwdrivers and a hammer, tap out the snap ring.
Use a piece of cloth to prevent the snap ring from flying off.
33336
24.REMOVE 5TH GEAR
Using SST and a press, remove the 5th gear and synchronizer ring.
33428B
25.REMOVE 5TH COUNTER GEAR BEARING
Remove the 5th counter gear bearing from the output shaft.
33369
26.REMOVE NO. 3 SYNCHRONIZER RING SET
Remove the No. 3 synchronizer ring from the 5th gear.
33395
27.REMOVE NO. 3 TRANSMISSION HUB SLEEVE
Remove the No. 3 transmission hub sleeve, 3 shifting keys and 2 springs from the No. 3 transmission clutch hub.
Use a piece of cloth to prevent the spring from flying off.