Home › Drivetrain › H150F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION UNIT
RM2660E _52 Drivetrain _052809 H150F MANUAL TRANSMISSION / TRANSAXLE _0255327 MANUAL TRANSMISSION UNIT A

H150F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION UNIT  DISASSEMBLY  


PROCEDURE

Hide 33019C 1.REMOVE TRANSMISSION BREATHER SUB-ASSEMBLY (for 1GR-FE)

C178013

a.

Loosen the hose clamp, and remove the breather hose.


Hide 33019C 2.REMOVE TRANSMISSION BREATHER SUB-ASSEMBLY (for 1VD-FTV)

C178014

a.

Remove the wire harness clamp.


b.

Loosen the hose clamp, and remove the breather hose.


Hide 31111 3.REMOVE CLUTCH HOUSING

C174421E06
0.073,0.094 1.177,0.365 1.104,0.271 12 false for 1VD-FTV: 0.073,2.427 1.146,2.646 1.073,0.219 12 false for 1GR-FE:

a.

Remove the 10 bolts and clutch housing.


Hide 33101A 4.REMOVE FILLER PLUG

C174902

a.

Remove the filler plug.


b.

Remove the gasket from the filler plug.


Hide 33101A 5.REMOVE DRAIN PLUG

C172955

a.

Remove the drain plug.


b.

Remove the gasket from the drain plug.


Hide 33111A 6.REMOVE MANUAL TRANSMISSION CASE PLUG

C174726

a.

Using a T55 "TORX" socket wrench, remove the transmission case plug.


b.

Remove the gasket from the transmission case plug.


Hide 84210 7.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

C174428E02
1.229,1.146 0.99,0.49 0.99,0.49 0.719,0.49 true 0.323,0.417 0.688,0.667 0.365,0.25 10 true SST

a.

Disconnect the wire harness clamp.


b.

Using SST, remove the back-up light switch and gasket.

SST
09817-16011  


Hide 84225A 8.REMOVE SHIFT POSITION SWITCH (for 1VD-FTV)

C174429E02
1.99,0.896 2.396,0.115 true 2.396,0.125 2.573,0.125 true 2.635,0.052 3,0.219 0.365,0.167 10 false SST

a.

Disconnect the wire harness clamp.


b.

Using SST, remove the shift position switch and gasket.

SST
09817-16011  


Hide 33528L 9.REMOVE CONTROL SHAFT COVER

C174728

a.

Remove the 6 bolts and control shaft cover.


Hide 33280 10.REMOVE REVERSE RESTRICT PIN ASSEMBLY

C174430

a.

Remove the 2 restrict pins.


Hide 33506F 11.REMOVE FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

C174717

a.

Remove the 4 bolts.


b.
C174718

Using a plastic-faced hammer, remove the floor shift control shift lever retainer.


Hide 33283 12.REMOVE NO. 1 REVERSE RESTRICT PIN

C171347

a.

Remove the slotted pin.


b.
C171384

Remove the No. 1 reverse restrict pin and spring.


Hide 33130G 13.REMOVE TRANSMISSION OIL PUMP COVER

C174391

a.

Remove the 5 bolts and oil pump cover.


b.
C171196

Using a magnet hand, remove the 2 pins.


c.

Remove the oil pump cover O-ring from the oil pump cover.


Hide 33130H 14.REMOVE TRANSMISSION OIL PUMP COVER OIL SEAL

C178035E02
1.354,0.177 1.438,0.177 1.438,0.177 1.135,1.156 true 0.354,0.104 1.365,0.26 1.01,0.156 10 false Protective Tape

a.

Using a screwdriver, pry out the oil pump cover oil seal.

NOTICE:

Be careful not to damage the oil seal and oil pump cover contact surfaces.


HINT:

Tape the screwdriver tip before use.



Hide 33131 15.REMOVE FRONT BEARING RETAINER (MTM)

C171381

a.

Remove the 8 bolts and front bearing retainer.


Hide 33131A 16.REMOVE TRANSMISSION FRONT BEARING RETAINER OIL SEAL

C171295E02
2.49,1.208 2.146,1.208 2.146,1.208 1.708,0.708 true 2.573,1.146 3.229,1.479 0.656,0.333 10 false Protective Tape

a.

Using a screwdriver, pry out the oil seal.

NOTICE:

Be careful not to damage the oil seal and front bearing retainer contact surfaces.


HINT:

Tape the screwdriver tip before use.



Hide 33261C 17.REMOVE SHIFT AND SELECT LEVER SHAFT

C174901

a.

Using a 14 mm hexagon wrench, remove the interlock hole plug.


b.
C174721E03
2.563,1.167 2.75,1.875 false 2.75,1.875 2.208,1.875 false 1.198,0.99 1.521,0.427 false 1.521,0.427 1.677,0.427 false 2.271,1.177 2.344,1.573 false 2.344,1.573 2.229,1.573 false 1.708,0.333 3.146,0.531 1.438,0.198 10 false Shift And Select Lever 0.49,1.479 2.375,1.688 1.885,0.208 10 false Shift And Select Lever Shaft 0.958,1.76 2.313,1.958 1.354,0.198 10 false Shift Lever Housing 0.448,0.219 1.198,0.406 0.75,0.188 10 false Front Side

Remove the 3 bolts, shift and select lever shaft, shift and select lever and shift lever housing.


Hide 36107A 18.REMOVE TRANSFER ADAPTER SUB-ASSEMBLY

C174720

a.

Remove the 11 bolts and transfer adapter.


Hide 33112C 19.REMOVE TRANSFER ADAPTER STRAIGHT PIN AND RING PIN

C358659E01
0.177,0.156 1.865,0.354 1.688,0.198 10 false Upper Side: 0.229,2.021 1.917,2.219 1.688,0.198 10 false Rear Side:

a.

Remove the 4 straight pins from the transfer adapter.


b.

Remove the 2 ring pins from the transfer adapter.


Hide 36117D 20.REMOVE TRANSFER ADAPTER PLUG

C174722

a.

Using a T40 "TORX" socket wrench, remove the transfer adapter plug.


Hide 33408 21.REMOVE MANUAL TRANSMISSION OIL STRAINER SUB-ASSEMBLY

C358660

a.

Remove the 2 bolts and oil strainer.


b.

Remove the O-ring from the oil strainer.


Hide 33449B 22.REMOVE TRANSMISSION MAGNET

C171351

a.

Remove the transmission magnet.


Hide 33464 23.REMOVE NO. 2 REVERSE IDLER THRUST WASHER

C171200

a.

Remove the thrust washer.


Hide 33461 24.REMOVE REVERSE IDLER GEAR

a.

Remove the reverse idler gear.


Hide 33402A 25.REMOVE REVERSE IDLER GEAR BUSH OR BEARING

a.

Remove the bearing.


Hide 33462 26.REMOVE REVERSE IDLER THRUST WASHER

a.

Remove the thrust washer.


Hide 33451 27.REMOVE REVERSE IDLER GEAR SHAFT

a.

Remove the reverse idler gear shaft.


Hide 33451A 28.REMOVE REVERSE IDLER GEAR SHAFT WOODRUFF KEY

a.

Remove the woodruff key from the reverse idler gear shaft.


Hide 33101 29.REMOVE MANUAL TRANSMISSION CASE SUB-ASSEMBLY

C171195

a.

Using a snap ring expander, remove the 2 snap rings from the input shaft and counter gear.


b.
C171197

Using a brass bar and hammer, carefully tap the transmission case.


c.

Remove the transmission case from the intermediate plate.


Hide 33124C 30.REMOVE NO. 1 OIL RECEIVER PIPE (MTM)

C358664

a.

Remove the 2 bolts and oil receiver pipe from the transmission case.


Hide 33112C 31.REMOVE TRANSFER ADAPTER STRAIGHT PIN

C358641E01
0.281,0.167 1.406,0.396 1.125,0.229 10 false Upper Side: 4.083,0.167 5.208,0.396 1.125,0.229 10 false Front Side:

a.

Remove the 4 straight pins from the transmission case.


Hide 33112C 32.REMOVE INTERMEDIATE PLATE STRAIGHT PIN

C358642E01
0.25,0.198 1.938,0.396 1.688,0.198 10 false Front Side: 4.052,0.208 5.74,0.406 1.688,0.198 10 false Rear Side:

a.

Remove the 4 straight pins from the intermediate plate.


Hide 33125B 33.REMOVE MANUAL TRANSMISSION CASE RECEIVER

a.
C171355

Remove the 3 bolts and oil receiver from the intermediate plate.


Hide 33275F 34.REMOVE SHIFT DETENT BALL PLUG

C171201

a.

Using a T40 "TORX" socket wrench, remove the 4 ball plugs.


b.

Using a magnet hand, remove the 4 springs and 4 balls.


Hide 33244B 35.REMOVE SHIFT FORK SHAFT SNAP RING

C171202

a.

Using 2 screwdrivers and a hammer, tap out the 4 snap rings.

HINT:

Use a piece of cloth to prevent the snap ring from flying off.



Hide 33245G 36.REMOVE NO. 4 GEAR SHIFT FORK SHAFT

C171203

a.

Remove the No. 4 gear shift fork set bolt.


b.
C171204

Remove the No. 4 gear shift fork shaft and 2 balls.


Hide 33211 37.REMOVE REVERSE SHIFT FORK

a.

Remove the reverse shift fork.


Hide 33244D 38.REMOVE NO. 3 GEAR SHIFT FORK SHAFT

C171205

a.

Using a magnet hand, remove the ball.


b.
C171216

Remove the No. 3 gear shift fork set bolt.


c.

Remove the No. 3 shift gear fork shaft and reverse shift head.


d.
C171357

Using a magnet hand, remove the interlock pin from the No. 3 gear shift fork shaft.


Hide 33214G 39.REMOVE NO. 3 GEAR SHIFT FORK

a.

Remove the No. 3 gear shift fork.


Hide 33242 40.REMOVE NO. 1 GEAR SHIFT FORK SHAFT

C171217

a.

Using a magnet hand, remove the interlock pin.


b.
C171218

Remove the No. 1 gear shift fork set bolt.


c.

Remove the No. 1 gear shift fork shaft.


d.
C171358

Using a magnet hand, remove the interlock pin from the No. 1 gear shift fork shaft.


Hide 33212A 41.REMOVE NO. 1 GEAR SHIFT FORK

a.

Remove the No. 1 gear shift fork.


Hide 33243A 42.REMOVE NO. 2 GEAR SHIFT FORK SHAFT

C171219

a.

Using a magnet hand, remove the interlock pin.


b.
C171220

Remove the No. 2 gear shift fork set bolt.


c.

Remove the No. 2 gear shift fork shaft.


Hide 33213G 43.REMOVE NO. 2 GEAR SHIFT FORK

a.

Remove the No. 2 gear shift fork.


Hide 33393A 44.REMOVE NO. 3 TRANSMISSION CLUTCH HUB SHAFT SNAP RING

a.
C313966C02
1.792,1.292 2.302,1.115 2.302,1.115 1.885,1.344 true 2.344,1.021 2.656,1.219 0.313,0.198 10 false *a
*a Protective Tape


Using 2 screwdrivers and a hammer, tap out the snap ring.

NOTICE:
·

Do not damage the output shaft.

·

Use a piece of cloth to prevent the snap ring from flying off.



HINT:

Tape the screwdriver tip before use.



Hide 33363 45.REMOVE NO. 1 TRANSMISSION HUB SLEEVE

a.
C377625

Remove the No. 1 transmission hub sleeve from the No. 4 transmission clutch hub.


Hide 33331 46.REMOVE REVERSE GEAR

a.
C377626C01
1.365,0.542 1.552,0.24 1.552,0.24 1.729,0.24 false 2.063,1.927 2.375,2.083 0.313,0.156 10 false *a 0.083,1.656 0.396,1.813 0.313,0.156 10 false *b 1.813,0.177 2.271,0.375 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST, remove the reverse gear, reverse synchronizer ring set and No. 4 transmission clutch hub from the output shaft.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04010, 09954-04020, 09955-04021, 09957-04010, 09958-04011)
09950-60010  (09951-00300)


Hide 33352B 47.REMOVE NO. 4 TRANSMISSION CLUTCH HUB

a.
C313436

Remove the transmission clutch hub from the reverse gear.


b.
C313419C02
2.563,1.344 2.49,1.542 2.49,1.542 2.375,1.542 true 2.573,0.563 2.5,0.76 2.5,0.76 2.385,0.76 true 1.073,0.51 0.979,0.229 0.979,0.229 0.865,0.229 true 2.229,0.677 2.542,0.875 0.313,0.198 10 false *a 2.208,1.469 2.521,1.667 0.313,0.198 10 false *a 0.698,0.146 1.01,0.344 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, remove the 3 shifting keys and 3 springs from the No. 4 transmission clutch hub.

NOTICE:
·

Do not drop the shifting key.

·

Do not damage the No. 4 transmission clutch hub and spring.



HINT:

Push down the spring as shown in the illustration and remove the shifting key.



Hide 33049 48.REMOVE REVERSE SYNCHRONIZER RING SET

a.

Remove the reverse synchronizer ring set from the reverse gear.


Hide 33331A 49.REMOVE REVERSE GEAR BEARING

a.

Remove the reverse gear bearing.


Hide 33151 50.REMOVE OUTPUT SHAFT REAR BEARING(MTM) RETAINER

C171360

a.

Remove the 4 bolts and rear bearing retainer.


Hide 33421 51.REMOVE COUNTER GEAR

C174896

a.

Using a snap ring expander, remove the snap ring.


b.
C171228E01
2.799,0.465 3.164,0.648 0.365,0.183 10 SST 2.309,0.92 2.51,0.56 false 2.51,0.56 2.759,0.56 false

Using SST, remove the outer race.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04020, 09955-04011, 09957-04010, 09958-04011)

NOTICE:

Do not drop the counter gear. Hold the front side of the counter gear when removing the bearing outer race.



c.
C171230

Using a screwdriver, remove the center bearing and counter gear.


Hide 52.REMOVE INPUT SHAFT ASSEMBLY

C171362

a.

Remove the input shaft from the output shaft.

NOTICE:

Do not drop the input shaft bearing.



Hide 33368 53.REMOVE NO. 2 SYNCHRONIZER RING

a.

Remove the No. 2 synchronizer ring from the input shaft.


Hide 33321B 54.REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING

C171364

a.

Using a snap ring expander, remove the snap ring.


Hide 55.REMOVE OUTPUT SHAFT ASSEMBLY

C171231

a.

Remove the output shaft from the intermediate plate by pulling on the output shaft and tapping on the intermediate plate with a plastic-faced hammer.