Home › Drivetrain › H150F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION UNIT
RM2660E _52 Drivetrain _052809 H150F MANUAL TRANSMISSION / TRANSAXLE _0255327 MANUAL TRANSMISSION UNIT A

H150F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION UNIT  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL OUTPUT SHAFT ASSEMBLY

a.
C171363

Fix the transmission intermediate plate in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the output shaft by lightly tapping on the back side of the intermediate plate with a plastic-faced hammer.

HINT:

Perform the procedure while pulling the output shaft assembly to the rear side by hand.



Hide 33321B 2.INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING

C171364

a.

Using a snap ring expander, install the snap ring to the output shaft bearing.


Hide 33368 3.INSTALL NO. 2 SYNCHRONIZER RING

a.

Install the No. 2 synchronizer ring to the input shaft.


Hide 4.INSTALL INPUT SHAFT ASSEMBLY

C171365E01
2.031,0.053 2.877,0.264 0.846,0.211 10 Shifting Key 2.174,0.483 3.013,0.694 0.839,0.211 10 Key Groove 1.311,0.649 1.836,0.127 false 1.836,0.127 1.985,0.127 false 1.557,0.873 1.957,0.569 false 1.957,0.569 2.123,0.569 false

a.

Install the input shaft to the output shaft.

HINT:

Align the shifting key of the synchronizer ring with the groove of the clutch hub.



b.

Install the clutch hub and confirm that the gear and synchronizer ring move smoothly.


Hide 33421 5.INSTALL COUNTER GEAR

a.

Install the counter gear to the intermediate plate.


b.
C171366

Install the center bearing to the counter gear.


c.
C171367

Using a snap ring expander, install the snap ring to the outer race.


d.
C171229

Using a brass bar and hammer, lightly tap the bearing outer race uniformly to install it.

NOTICE:

Do not drop the counter gear. Hold the front side of the counter gear.



Hide 33151 6.INSTALL OUTPUT SHAFT REAR BEARING(MTM) RETAINER

C171360

a.

Install the output shaft rear bearing retainer to the intermediate plate with the 4 bolts.

Torque:
18 N*m (185 kgf*cm, 13 ft.*lbf)


Hide 33331A 7.INSTALL REVERSE GEAR BEARING

a.
C313423

Coat the reverse gear bearing with gear oil, and install it to the output shaft.


Hide 33331 8.INSTALL REVERSE GEAR

C314917

a.

Coat the reverse gear with gear oil, and install it to the output shaft.

HINT:

Apply gear oil to the inner diameter surface and thrust surface of the reverse gear.



Hide 33049 9.INSTALL REVERSE SYNCHRONIZER RING SET

a.

Apply gear oil to the reverse synchronizer ring set and tapered cone surface of the reverse gear.


b.
C314916C02
2.917,1.656 3,1.25 3,1.25 3.135,1.25 false 2.552,1.438 2.635,1.031 2.635,1.031 2.771,1.031 false 2.198,1.271 2.281,0.865 2.281,0.865 2.417,0.865 false 2.49,0.781 2.802,0.938 0.313,0.156 10 false *1 2.833,0.969 3.146,1.125 0.313,0.156 10 false *2 3.198,1.177 3.406,1.333 0.208,0.156 10 false *3
*1 Outer Ring
*2 Middle Ring
*3 Inner Ring


Install the reverse synchronizer ring set to the reverse gear.

NOTICE:
·

Align the claw of the middle ring and the cutout of the reverse gear.

·

Align the claw of the inner ring and the key groove of the outer ring.




Hide 33352B 10.INSTALL NO. 4 TRANSMISSION CLUTCH HUB

a.
C313949C02
2.396,0.771 2.51,0.771 2.51,0.771 2.573,0.552 true 2.375,1.667 2.49,1.667 2.49,1.667 2.552,1.448 true 0.896,0.208 1.01,0.208 1.01,0.208 1.094,0.469 true 2.24,0.698 2.552,0.854 0.313,0.156 10 false *a 2.219,1.594 2.531,1.75 0.313,0.156 10 false *a 0.74,0.125 1.052,0.281 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver, install the 3 shifting keys and 3 springs to the No. 4 transmission clutch hub.

NOTICE:

Lightly move the shifting key with your finger and check that it does not separate from the No. 4 transmission clutch hub.


HINT:
·

Push down the spring as shown in the illustration when installing the shifting key.

·

Tape the screwdriver tip before use.




b.
C313947C02
2.5,2.052 2.667,1.667 2.667,1.667 2.823,1.667 true 2.875,1.604 3.333,1.802 0.458,0.198 10 false SST
V100135

Front Side


Using SST and a hammer, install the No. 4 transmission clutch hub.

SST
09316-60011  (09316-00011)

NOTICE:
·

Install in the correct direction.

·

Align the key groove of the reverse synchronizer ring set with the shifting key position when installing.



HINT:

Align the shifting key of the synchronizer ring with the groove of the clutch hub.



c.

Install the clutch hub and confirm that the gear and synchronizer ring move smoothly.


Hide 33363 11.INSTALL NO. 1 TRANSMISSION HUB SLEEVE

a.

Apply a light coat of gear oil to the spline of No. 1 transmission hub sleeve.


b.
C377627C01
0,0 0,0 false
V100135

Front Side


Install the No. 1 transmission hub sleeve to the No. 4 transmission clutch hub.

NOTICE:

Do not mistake the installation direction of the No. 1 transmission hub sleeve.



Hide 33393A 12.INSTALL NO. 3 TRANSMISSION CLUTCH HUB SHAFT SNAP RING

C171371

a.

Select a new snap ring that will allow minimum clearance.

Standard Clearance:

0.1 mm (0.00393 in.) or less


Snap Ring Thickness:
Part No. Thickness Mark
90520-34018 2.40 to 2.45 mm
(0.0945 to 0.0965 in.)
A
90520-34019 2.45 to 2.50 mm
(0.0965 to 0.0984 in.)
B
90520-34020 2.50 to 2.55 mm
(0.0984 to 0.100 in.)
C
90520-34021 2.55 to 2.60 mm
(0.100 to 0.102 in.)
D
90520-34022 2.60 to 2.65 mm
(0.102 to 0.104 in.)
E
90520-34023 2.65 to 2.70 mm
(0.104 to 0.106 in.)
F



b.
C171372

Using a brass bar and hammer, install the snap ring to the output shaft.


Hide 33331 13.INSPECT REVERSE GEAR THRUST CLEARANCE

C171221

a.

Using a feeler gauge, measure the reverse gear thrust clearance.

Standard Clearance:

0.15 to 0.52 mm (0.00591 to 0.0204 in.)


If the clearance is outside the specification, replace the defective gear or shaft.


Hide 33213G 14.INSTALL NO. 2 GEAR SHIFT FORK

a.

Install the No. 2 gear shift fork.


Hide 33243A 15.INSTALL NO. 2 GEAR SHIFT FORK SHAFT

C171220

a.

Install the No. 2 gear shift fork shaft to the No. 2 gear shift fork and intermediate plate with the bolt.

Torque:
46 N*m (472 kgf*cm, 34 ft.*lbf)


Hide 33212A 16.INSTALL NO. 1 GEAR SHIFT FORK

a.

Install the No. 1 gear shift fork.


Hide 33242 17.INSTALL NO. 1 GEAR SHIFT FORK SHAFT

C171219

a.

Using a magnet hand, install the interlock pin to the intermediate plate.


b.
C171374

Apply MP grease to the interlock pin.


c.

Install the interlock pin to the No. 1 gear shift fork shaft.


d.
C171218

Install the No. 1 gear shift fork shaft to the No. 2 gear shift fork and intermediate plate with the bolt.

Torque:
46 N*m (472 kgf*cm, 34 ft.*lbf)


Hide 33214G 18.INSTALL NO. 3 GEAR SHIFT FORK

a.

Install the No. 3 gear shift fork.


Hide 33244D 19.INSTALL NO. 3 GEAR SHIFT FORK SHAFT

C171217

a.

Using a magnet hand, install the interlock pin to the intermediate plate.


b.
C171357

Apply MP grease to the interlock pin.


c.

Install the interlock pin to the No. 3 gear shift fork shaft.


d.
C171216

Install the No. 3 gear shift fork shaft to the No. 3 gear shift fork and intermediate plate with the bolt.

Torque:
46 N*m (472 kgf*cm, 34 ft.*lbf)


Hide 33211 20.INSTALL REVERSE SHIFT FORK

a.

Install the reverse shift fork.


Hide 33245G 21.INSTALL NO. 4 GEAR SHIFT FORK SHAFT

C171205

a.

Using a magnet hand, install the ball to the intermediate plate.


b.
C171377

Using a magnet hand, install the ball to the reverse shift head.


c.
C171203

Install the No. 4 gear shift fork shaft to the reverse gear shift fork and intermediate plate with the bolt.

Torque:
34 N*m (350 kgf*cm, 25 ft.*lbf)


Hide 33244B 22.INSTALL SHIFT FORK SHAFT SNAP RING

C171378

a.

Using a brass bar and hammer, install the 4 snap rings.


Hide 33275F 23.INSTALL SHIFT DETENT BALL PLUG

C171201

a.

Install the 4 balls and 4 springs to the intermediate plate.


b.

Apply adhesive to 2 or 3 threads of the 4 detent ball plugs.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Using a T40 "TORX" socket wrench, install the 4 detent ball plugs.

Torque:
19 N*m (190 kgf*cm, 14 ft.*lbf)


Hide 33125B 24.INSTALL MANUAL TRANSMISSION CASE RECEIVER

C171355

a.

Install the transmission case receiver to the intermediate plate with the 3 bolts.

Torque:
18 N*m (185 kgf*cm, 13 ft.*lbf)


Hide 33112C 25.INSTALL INTERMEDIATE PLATE STRAIGHT PIN

C358643E01
0.417,0.323 2.104,0.521 1.688,0.198 10 false Front Side: 3.885,0.323 5.573,0.521 1.688,0.198 10 false Rear Side: 4.74,3.438 6.427,3.635 1.688,0.198 10 false 7.0 to 9.0 mm

a.

Using a plastic-faced hammer, tap 4 new straight pins into the intermediate plate.

Standard Protrusion Height:

7.0 to 9.0 mm (0.276 to 0.354 in.)



Hide 33112C 26.INSTALL TRANSFER ADAPTER STRAIGHT PIN

C358665E01
0.188,0.115 1.875,0.313 1.688,0.198 10 false Upper Side: 1.177,2.729 2.865,2.927 1.688,0.198 10 false 4.0 to 6.0 mm

a.

Using a plastic-faced hammer, tap 2 new straight pins into the transmission case.

Standard Protrusion Height:

4.0 to 6.0 mm (0.158 to 0.236 in.)



b.
C358666E01
0.188,0.135 1.875,0.333 1.688,0.198 10 false Front Side: 2.292,1.563 3.385,1.792 1.094,0.229 10 false 9.0 to 11.0 mm

Using a plastic-faced hammer, tap 2 new straight pins into the transmission case.

Standard Protrusion Height:

9.0 to 11.0 mm (0.355 to 0.433 in.)



Hide 33124C 27.INSTALL NO. 1 OIL RECEIVER PIPE (MTM)

C358664

a.

Install the oil receiver pipe to the transmission case with the 2 bolts.

Torque:
12 N*m (120 kgf*cm, 9 ft.*lbf)


Hide 33101 28.INSTALL MANUAL TRANSMISSION CASE SUB-ASSEMBLY

C174900E02
0.102,0.301 0.694,0.624 0.592,0.324 10 Seal Packing 1.202,0.385 0.728,0.385 false

a.

Apply seal packing to the transmission case, as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Parts must be assembled within 10 minutes of application. Otherwise, the packing (FIPG) material must be removed and reapplied.



b.
C171380

Install the transmission case by lightly tapping it into place with a plastic-faced hammer.

NOTICE:

Make sure that the oil receiver installed on the transmission side is above the oil application area of the intermediate plate side oil receiver.



c.
C171195

Using a snap ring expander, install the 2 snap rings to the counter gear and input shaft.


Hide 33451A 29.INSTALL REVERSE IDLER GEAR SHAFT WOODRUFF KEY

C171200

a.

Install the woodruff key to the reverse idler gear shaft.


Hide 33451 30.INSTALL REVERSE IDLER GEAR SHAFT

a.

Install the reverse idler gear shaft to the intermediate plate.


Hide 33462 31.INSTALL REVERSE IDLER THRUST WASHER

a.

Install the thrust washer to the reverse idler gear shaft.

NOTICE:
·

Align the protrusion of the washer with the groove of the intermediate plate during installation.

·

Install the washer so that the dimpled surface of the washer contacts the reverse idler gear thrust surface.




Hide 33402A 32.INSTALL REVERSE IDLER GEAR BUSH OR BEARING

a.

Install the bearing to the reverse idler gear shaft.


Hide 33461 33.INSTALL REVERSE IDLER GEAR

a.

Install the reverse idler gear to the reverse idler gear shaft.


Hide 33464 34.INSTALL NO. 2 REVERSE IDLER THRUST WASHER

a.

Install the thrust washer to the reverse idler gear shaft.

NOTICE:

Install the washer so that the dimpled surface of the washer contacts the reverse idler gear thrust surface.



Hide 33449B 35.INSTALL TRANSMISSION MAGNET

C171351

a.

Install the transmission magnet to the intermediate plate.


Hide 33408 36.INSTALL MANUAL TRANSMISSION OIL STRAINER SUB-ASSEMBLY

C358660

a.

Install a new O-ring to the oil strainer.


b.

Apply a light coat of gear oil to the O-ring.


c.

Install the oil strainer to the transfer adapter with the 2 bolts.

Torque:
12 N*m (120 kgf*cm, 9 ft.*lbf)


Hide 33112C 37.INSTALL TRANSFER ADAPTER STRAIGHT PIN AND RING PIN

C358644E01
0.521,0.354 2.208,0.552 1.688,0.198 10 false Upper Side: 3.844,0.344 5.531,0.542 1.688,0.198 10 false Rear Side: 2.521,0.792 2.792,0.969 0.271,0.177 10 false A 1.646,1.969 1.917,2.146 0.271,0.177 10 false A 4.594,1.708 4.865,1.885 0.271,0.177 10 false A 5.521,1.594 5.792,1.771 0.271,0.177 10 false A 4.073,1.385 4.313,1.552 0.24,0.167 10 false B 6.104,1.698 6.344,1.865 0.24,0.167 10 false B 4.104,2.708 5.208,2.896 1.104,0.188 10 false A: Straight Pin 5.417,2.698 6.521,2.885 1.104,0.188 10 false B: Ring Pin 4.167,3.448 5.271,3.635 1.104,0.188 10 false 4.0 to 6.0 mm 5.323,3.448 6.427,3.635 1.104,0.188 10 false 4.0 to 6.0 mm

a.

Using a plastic-faced hammer, tap in 4 new straight pins and 2 new ring pins to the transfer adapter.

Standard Protrusion Height A (Straight Pin):

4.0 to 6.0 mm (0.157 to 0.236 in.)


Standard Protrusion Height B (Ring Pin):

4.0 to 6.0 mm (0.157 to 0.236 in.)



Hide 36107A 38.INSTALL TRANSFER ADAPTER SUB-ASSEMBLY

C174899E03
2.167,0.25 2.49,0.25 false 2.542,0.177 3.115,0.542 0.573,0.365 10 false Seal Packing

a.

Apply seal packing to the transfer adapter, as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Parts must be assembled within 10 minutes of application. Otherwise, the packing (FIPG) material must be removed and reapplied.



b.
C174720E02
1.052,0.135 0.667,0.135 false 1.542,0.563 1.719,0.74 0.177,0.177 10 true A 0.708,0.354 0.885,0.531 0.177,0.177 10 false B 1.906,1.469 2.083,1.646 0.177,0.177 10 false B 1.406,1.458 1.583,1.635 0.177,0.177 10 false B 0.438,1.969 0.615,2.146 0.177,0.177 10 false B 0.292,1.188 0.469,1.365 0.177,0.177 10 false B 0.396,0.604 0.573,0.781 0.177,0.177 10 false B 2.698,1.813 2.875,1.99 0.177,0.177 10 false B 2.833,1.115 3.01,1.292 0.177,0.177 10 false B 2.833,0.583 3.01,0.76 0.177,0.177 10 false B 2.698,0.073 2.875,0.25 0.177,0.177 10 false B 0.031,0.031 0.615,0.208 0.583,0.177 10 false Bracket

Install the transfer adapter and bracket to the transmission case with the 11 bolts.

Torque:
37 N*m (380 kgf*cm, 27 ft.*lbf)

Bolt Length:
Item Length
Bolt A 110 mm (4.33 in.)
Bolt B 70 mm (2.75 in.)



Hide 36117D 39.INSTALL TRANSFER ADAPTER PLUG

C174722

a.

Using a T40 "TORX" socket wrench, install the transfer adapter plug to the transfer adapter.

Torque:
19 N*m (190 kgf*cm, 14 ft.*lbf)


Hide 33261C 40.INSTALL SHIFT AND SELECT LEVER SHAFT

C174721E03
2.563,1.167 2.75,1.875 false 2.75,1.875 2.208,1.875 false 1.198,0.99 1.521,0.427 false 1.521,0.427 1.677,0.427 false 2.271,1.177 2.344,1.573 false 2.344,1.573 2.229,1.573 false 1.708,0.333 3.146,0.531 1.438,0.198 10 false Shift And Select Lever 0.49,1.479 2.375,1.688 1.885,0.208 10 false Shift And Select Lever Shaft 0.958,1.76 2.313,1.958 1.354,0.198 10 false Shift Lever Housing 0.448,0.219 1.198,0.406 0.75,0.188 10 false Front Side

a.

Install the shift and select lever, shift lever housing, and shift and select lever shaft to the transmission as shown in the illustration.


b.

Install the 2 bolts to the shift and select lever.

Torque:
38 N*m (390 kgf*cm, 28 ft.*lbf)


c.

Install the bolt to the shift lever housing.

Torque:
38 N*m (390 kgf*cm, 28 ft.*lbf)


d.
C174901

Using a 14 mm hexagon wrench, install the interlock hole plug to the transfer adapter.

Torque:
18 N*m (185 kgf*cm, 13 ft.*lbf)


Hide 33131A 41.INSTALL TRANSMISSION FRONT BEARING RETAINER OIL SEAL

C171296E01
2.753,0.689 3.210,0.882 0.457,0.193 10 SST 2.309,1.24 2.711,0.796 false 2.711,0.796 2.256,0.952 false

a.

Using SST and a press, drive in a new oil seal.

SST
09950-60010  (09951-00460)
09950-70010  (09951-07150)

Standard Drive in Depth:

15.4 to 16.2 mm (0.607 to 0.637 in.)



b.

Apply gear oil to the lip of the oil seal.


Hide 33131 42.INSTALL FRONT BEARING RETAINER (MTM)

C171194E03
2.281,1.021 2.615,1.021 false 2.646,0.948 3.208,1.313 0.563,0.365 10 false Seal Packing

a.

Apply seal packing to the front bearing retainer, as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Parts must be assembled within 10 minutes of application. Otherwise, the packing (FIPG) material must be removed and reapplied.



b.

Apply adhesive to 2 or 3 threads of the bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.
C171381

Install the front bearing retainer to the transmission case with the 8 bolts.

Torque:
17 N*m (170 kgf*cm, 12 ft.*lbf)


Hide 33130H 43.INSTALL TRANSMISSION OIL PUMP COVER OIL SEAL

C171303E03
0.823,1.635 0.5,0.333 true 0.5,0.333 0.958,0.917 true 1.802,1.656 2.198,0.198 2.198,0.198 2.292,0.198 true 0.188,0.229 0.583,0.417 0.396,0.188 10 false SST 2.375,0.115 3.24,0.313 0.865,0.198 10 false Dimension A

a.

Using SST and a hammer, tap a new oil seal into the oil pump cover in accordance with the dimension specified in the illustration.

SST
09950-70010  (09951-07150)
09950-60010  (09951-00640)


Hide 33130G 44.INSTALL TRANSMISSION OIL PUMP COVER

C171383

a.

Apply MP grease to the straight pins.


b.

Install the 2 straight pins.


c.

Install a new O-ring to the oil pump cover.


d.

Align the oil pump drive rotor groove with the straight pin, and install the oil pump cover to the transfer adapter.


e.

Apply adhesive to 2 or 3 threads of the bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



f.
C174391

Install the oil pump cover to the transfer adapter with the 5 bolts.

Torque:
17 N*m (170 kgf*cm, 12 ft.*lbf)


Hide 33283 45.INSTALL NO. 1 REVERSE RESTRICT PIN

C171384

a.

Install the No. 1 reverse restrict pin and spring to the shift lever retainer.


b.
C171385

Using a 5 mm pin punch and hammer, tap a new slotted pin into the shift lever retainer.


Hide 33506F 46.INSTALL FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

C171191E03
2.458,1.281 2.719,1.281 false 2.771,1.208 3.313,1.615 0.542,0.406 10 false Seal Packing

a.

Apply seal packing to the shift lever retainer, as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Parts must be assembled within 10 minutes of application. Otherwise, the packing (FIPG) material must be removed and reapplied.



b.

Apply adhesive to 2 or 3 threads of the bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.
C174717

Install the shift lever retainer to the transfer adapter with the 4 bolts.

Torque:
17 N*m (170 kgf*cm, 12 ft.*lbf)


Hide 33280 47.INSTALL REVERSE RESTRICT PIN ASSEMBLY

C174430

a.

Apply adhesive to 2 or 3 threads of the reverse restrict pins.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



b.

Install the 2 reverse restrict pins to the shift lever retainer.

Torque:
37 N*m (380 kgf*cm, 27 ft.*lbf)


Hide 33528L 48.INSTALL CONTROL SHAFT COVER

C174729E03
2.188,0.406 2.354,0.177 false 2.354,0.177 2.74,0.177 false 2.781,0.115 3.333,0.479 0.552,0.365 10 false Seal Packing

a.

Apply seal packing to the control shaft cover, as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Parts must be assembled within 10 minutes of application. Otherwise, the packing (FIPG) material must be removed and reapplied.



b.

Apply adhesive to 2 or 3 threads of the bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.
C174728

Install the control shaft cover to the manual transmission with the 6 bolts.

Torque:
17 N*m (170 kgf*cm, 12 ft.*lbf)


Hide 84225A 49.INSTALL SHIFT POSITION SWITCH (for 1VD-FTV)

C174429E02
1.99,0.896 2.396,0.115 true 2.396,0.125 2.573,0.125 true 2.635,0.052 3,0.219 0.365,0.167 10 false SST

a.

Using SST, install a new gasket and the shift position switch to the transmission.

SST
09817-16011  

Torque:
44 N*m (450 kgf*cm, 33 ft.*lbf)


b.

Connect the wire harness clamp.


Hide 84210 50.INSTALL BACK-UP LIGHT SWITCH ASSEMBLY

C174428E02
1.229,1.146 0.99,0.49 0.99,0.49 0.719,0.49 true 0.323,0.417 0.688,0.667 0.365,0.25 10 true SST

a.

Using SST, install a new gasket and the back-up light switch to the transmission.

SST
09817-16011  

Torque:
44 N*m (450 kgf*cm, 33 ft.*lbf)


b.

Connect the wire harness clamp.


Hide 33111A 51.INSTALL MANUAL TRANSMISSION CASE PLUG

C174726

a.

Using a T55 "TORX" socket wrench, install a new gasket and the manual transmission case plug to the transmission.

Torque:
37 N*m (380 kgf*cm, 27 ft.*lbf)


Hide 33101A 52.INSTALL DRAIN PLUG

C172955

a.

Install a new gasket and the drain plug to the manual transmission.

Torque:
37 N*m (380 kgf*cm, 27 ft.*lbf)


Hide 33101A 53.TEMPORARILY INSTALL FILLER PLUG

C174902

a.

Temporarily install a new gasket and the filler plug to the manual transmission.

Torque:
37 N*m (380 kgf*cm, 27 ft.*lbf)

HINT:

The filler plug will be tightened to a torque specification in the "Inspect Transmission Oil" procedure.



Hide 31111 54.INSTALL CLUTCH HOUSING

C174421E07
0.052,0.135 1.208,0.406 1.156,0.271 12 false for 1VD-FTV: 0.052,2.458 1.052,2.802 1,0.344 12 false for 1GR-FE: 0.844,2.948 1,3.125 0.156,0.177 10 false A 0.719,3.49 0.875,3.667 0.156,0.177 10 false B 2.479,4 2.635,4.177 0.156,0.177 10 true C 1.969,2.604 2.125,2.781 0.156,0.177 10 false B 2.448,2.938 2.604,3.115 0.156,0.177 10 false B 2.583,3.5 2.74,3.677 0.156,0.177 10 true B 2.271,4.406 2.427,4.583 0.156,0.177 10 false B 1.073,4.417 1.229,4.594 0.156,0.177 10 false B 0.844,3.979 1,4.156 0.156,0.177 10 true B 1.292,2.594 1.448,2.771 0.156,0.177 10 false A 0.854,0.76 1.01,0.938 0.156,0.177 10 true A 0.729,1.271 0.885,1.448 0.156,0.177 10 true B 2.469,1.75 2.625,1.927 0.156,0.177 10 true C 1.969,0.365 2.125,0.542 0.156,0.177 10 true B 2.438,0.719 2.594,0.896 0.156,0.177 10 true B 2.573,1.281 2.729,1.458 0.156,0.177 10 true B 2.25,2.146 2.479,2.375 0.229,0.229 10 true B 1.063,2.167 1.219,2.344 0.156,0.177 10 true B 0.854,1.74 1.01,1.917 0.156,0.177 10 true B 1.302,0.375 1.458,0.552 0.156,0.177 10 true A

a.

Apply adhesive to 2 or 3 threads of the bolts labeled A only.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



b.

Install the clutch housing with the 10 bolts.

Torque:
37 N*m (380 kgf*cm, 27 ft.*lbf)

Bolt Length:
Item Length
Bolt A 45 mm (1.77 in.)
Bolt B 45 mm (1.77 in.)
Bolt C 35 mm (1.38 in.)



Hide 33019C 55.INSTALL TRANSMISSION BREATHER SUB-ASSEMBLY (for 1VD-FTV)

C178014

a.

Connect the breather hose with the clamp.


b.

Install the wire harness clamp.


Hide 33019C 56.INSTALL TRANSMISSION BREATHER SUB-ASSEMBLY (for 1GR-FE)

C178013

a.

Connect the breather hose with the clamp.