Home › Drivetrain › JF2A (TRANSFER / 4WD / AWD) › TRANSFER ASSEMBLY › 2014.08–2015.08
RM2660E _52 Drivetrain _052810 JF2A TRANSFER / 4WD / AWD _0255336 TRANSFER ASSEMBLY G

JF2A TRANSFER / 4WD / AWD  TRANSFER ASSEMBLY  INSPECTION  


PROCEDURE

Hide 36211 1.INSPECT TRANSFER INPUT SHAFT

a.
C173633

Using a micrometer, measure the diameter of the input shaft journal surface.

Minimum Diameter:

68 mm (2.68 in.)


If the diameter is less than the minimum, replace the input shaft.


b.
C173634

Using a dial indicator, measure the inside diameter of the input shaft bush.

Maximum Inside Diameter:

46 mm (1.81 in.)


If the inside diameter is more than the maximum, replace the input shaft.


Hide 36270 2.INSPECT TRANSFER LOW PLANETARY GEAR ASSEMBLY

a.
C173635

Using a feeler gauge, measure the thrust clearance of the pinion gear.

Standard Clearance:

0.11 to 0.85 mm (0.00434 to 0.0334 in.)


Maximum Clearance:

0.85 mm (0.0334 in.)


If the clearance is more than the maximum, replace the low planetary gear assembly.


b.
C173636

Using a dial indicator, measure the radial clearance of the pinion gear.

Standard Clearance:

0.01 to 0.04 mm (0.000434 to 0.00150 in.)


Maximum Clearance:

0.04 mm (0.00150 in.)


If the clearance is more than the maximum, replace the low planetary gear assembly.


Hide 36231 3.INSPECT REAR TRANSFER OUTPUT SHAFT

a.
C173637E01
0.805,0.233 1.028,0.438 0.223,0.205 10 A 1.676,0.233 1.899,0.438 0.223,0.205 10 B 2.283,0.233 2.506,0.438 0.223,0.205 10 C

Using a micrometer, measure the diameter of the output shaft journals.

Minimum Diameter:
Journal Specified Condition
A 38 mm (1.50 in.)
B 42 mm (1.65 in.)
C 49 mm (1.93 in.)


If the diameter is less than the minimum, replace the output shaft.


Hide 36311F 4.INSPECT NO. 1 TRANSFER GEAR SHIFT FORK AND FRONT DRIVE CLUTCH SLEEVE

a.
C173639

Using a feeler gauge, measure the clearance between the clutch sleeve and gear shift fork.

Maximum Clearance:

0.8 mm (0.0315 in.)


If the clearance is more than the maximum, replace the clutch sleeve or shift fork.


Hide 36312F 5.INSPECT NO. 2 TRANSFER GEAR SHIFT FORK AND HIGH AND LOW CLUTCH SLEEVE

a.
C173638

Using a feeler gauge, measure the clearance between the clutch sleeve and gear shift fork.

Maximum Clearance:

3.15 mm (0.124 in.)


If the clearance is more than the maximum, replace the clutch sleeve or shift fork.


Hide 33367F 6.INSPECT NO. 1 SYNCHRONIZER RING (for Manual Transmission)

a.
C174149

Apply gear oil to the cone of the input shaft, and check that it does not turn in both directions while pushing the No. 1 synchronizer ring.

If it can turn, replace the No. 1 synchronizer ring.


b.
C174148

Push the No. 1 synchronizer ring to the cone of the input shaft. Measure the clearance between the No. 1 synchronizer ring and input shaft.

Standard Clearance:

0.86 to 1.54 mm (0.0339 to 0.0606 in.)


Minimum Clearance:

0.86 mm (0.0339 in.)


If the clearance is not as specified, replace the No. 1 synchronizer ring with a new one.