Home › Drivetrain › JF2A (TRANSFER / 4WD / AWD) › TRANSFER ASSEMBLY › from 2015.08
RM2660E _52 Drivetrain _052810 JF2A TRANSFER / 4WD / AWD _0255336 TRANSFER ASSEMBLY G

JF2A TRANSFER / 4WD / AWD  TRANSFER ASSEMBLY  INSPECTION  


PROCEDURE

Hide 36211 1.INSPECT TRANSFER INPUT SHAFT

a.
C173633

Using a micrometer, measure the diameter of the input shaft journal surface.

Minimum diameter:

68 mm (2.68 in.)


If the diameter is less than the minimum, replace the input shaft.


b.
C173634

Using a dial indicator, measure the inside diameter of the input shaft bush.

Maximum inside diameter:

46 mm (1.81 in.)


If the inside diameter is more than the maximum, replace the input shaft.


Hide 36270 2.INSPECT TRANSFER LOW PLANETARY GEAR ASSEMBLY

a.
C173635

Using a feeler gauge, measure the thrust clearance of the pinion gear.

Standard clearance:

0.11 to 0.85 mm (0.00434 to 0.0334 in.)


Maximum clearance:

0.85 mm (0.0334 in.)


If the clearance is more than the maximum, replace the low planetary gear assembly.


b.
C173636

Using a dial indicator, measure the radial clearance of the pinion gear.

Standard clearance:

0.01 to 0.04 mm (0.000394 to 0.00157 in.)


Maximum clearance:

0.04 mm (0.00157 in.)


If the clearance is more than the maximum, replace the low planetary gear assembly.


Hide 36231 3.INSPECT REAR TRANSFER OUTPUT SHAFT

a.
C173637E01
0.805,0.233 1.028,0.438 0.223,0.205 10 A 1.676,0.233 1.899,0.438 0.223,0.205 10 B 2.283,0.233 2.506,0.438 0.223,0.205 10 C

Using a micrometer, measure the diameter of the output shaft journals.

Minimum Diameter:
Journal Specified Condition
A 38 mm (1.50 in.)
B 42 mm (1.65 in.)
C 49 mm (1.93 in.)


If the diameter is less than the minimum, replace the output shaft.


Hide 36311F 4.INSPECT NO. 1 TRANSFER GEAR SHIFT FORK AND FRONT DRIVE CLUTCH SLEEVE

a.
C173639

Using a feeler gauge, measure the clearance between the clutch sleeve and gear shift fork.

Maximum clearance:

0.8 mm (0.0315 in.)


If the clearance is more than the maximum, replace the clutch sleeve or shift fork.


Hide 36312F 5.INSPECT NO. 2 TRANSFER GEAR SHIFT FORK AND HIGH AND LOW CLUTCH SLEEVE

a.
C173638

Using a feeler gauge, measure the clearance between the clutch sleeve and gear shift fork.

Maximum clearance:

3.15 mm (0.124 in.)


If the clearance is more than the maximum, replace the clutch sleeve or shift fork.


Hide 33367F 6.INSPECT NO. 1 SYNCHRONIZER RING (for Manual Transmission)

a.
C174149

Apply gear oil to the cone of the input shaft, and check that it does not turn in both directions while pushing the No. 1 synchronizer ring.

If it can turn, replace the No. 1 synchronizer ring.


b.
C174148

Push the No. 1 synchronizer ring to the cone of the input shaft. Measure the clearance between the No. 1 synchronizer ring and input shaft.

Standard clearance:

0.86 to 1.54 mm (0.0339 to 0.0606 in.)


Minimum clearance:

0.86 mm (0.0339 in.)


If the clearance is not as specified, replace the No. 1 synchronizer ring with a new one.


Hide 36410J 7.INSPECT TRANSFER SHIFT ACTUATOR ASSEMBLY (HIGH-LOW TRANSFER SHIFT ACTUATOR)

a.

Check the high-low transfer shift actuator.

i.

Check the high to low switch.

1.

Connect lines via a relay as shown in the illustration, and check that the actuator fork moves from the high to low position.

NOTICE:
·

Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, make sure to operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the DEFOG relay.


C179848E01
0.759,0.077 3.304,0.427 2.545,0.350 10 Component without harness connected: (High-low Transfer Shift Actuator) 2.23,3.741 2.603,3.900 0.373,0.159 10 HM1 1.873,4.078 2.217,4.248 0.343,0.170 10 HM2 1.255,4.061 1.563,4.231 0.309,0.170 10 HL1 1.638,4.115 1.839,4.278 0.200,0.163 10 N 0.243,3.824 0.622,3.987 0.378,0.163 10 GND 0.586,4.046 0.919,4.222 0.333,0.177 10 HL2 0.938,4.161 1.275,4.324 0.336,0.163 10 HL3 1.621,3.843 1.856,4.084 false 1.463,3.853 1.632,4.098 false 1.33,3.853 1.33,4.025 false 1.19,3.839 1.085,4.123 false 1.048,3.84 0.861,4.046 false 0.938,3.838 0.623,3.878 false 1.782,3.815 2.188,3.815 false 5.58,1.62 6.553,1.822 0.973,0.202 10 DEFOG Relay: 5.162,2.29 5.346,2.471 0.185,0.181 10 1 6.591,3.907 6.755,4.100 0.164,0.193 10 2 6.769,2.321 6.910,2.486 0.141,0.165 10 4 6.897,3.072 7.063,3.263 0.166,0.191 10 5 4.783,3.063 4.950,3.224 0.167,0.161 10 3 5.278,2.365 5.532,2.365 5.532,2.365 6.011,2.788 false 6.076,3.14 6.501,2.403 6.501,2.403 6.675,2.403 false 6.417,3.14 6.834,3.14 false 5.72,3.14 4.934,3.14 false 6.011,3.512 6.415,3.979 6.415,3.979 6.536,3.979 false 0.222,0.901 1.059,1.084 0.837,0.184 10 High → Low:

2.

After the high to low switch is complete, check the neutral position detection switch and limit switch.

(a)

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (N)* - 7 (GND) After high to low switch is complete 10 kΩ or higher
4 (HL1) - 7 (GND) After high to low switch is complete 10 kΩ or higher
5 (HL3) - 7 (GND) After high to low switch is complete 10 kΩ or higher
6 (HL2) - 7 (GND) After high to low switch is complete Below 1 Ω


*: for Manual Transmission

If there is a malfunction, replace the transfer shift actuator assembly.




ii.

Check the low to high switch.

1.

Connect lines via a relay as shown in the illustration, and check that the actuator fork moves from the low to high position.

NOTICE:
·

Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, make sure to operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the DEFOG relay.


C179849E01
0.759,0.156 3.304,0.507 2.545,0.350 10 Component without harness connected: (High-low Transfer Shift Actuator) 2.23,3.741 2.603,3.900 0.373,0.159 10 HM1 1.873,4.078 2.217,4.248 0.343,0.170 10 HM2 1.255,4.061 1.563,4.231 0.309,0.170 10 HL1 1.638,4.115 1.839,4.278 0.200,0.163 10 N 0.243,3.824 0.622,3.987 0.378,0.163 10 GND 0.586,4.046 0.919,4.222 0.333,0.177 10 HL2 0.938,4.161 1.275,4.324 0.336,0.163 10 HL3 1.621,3.843 1.856,4.084 false 1.463,3.853 1.632,4.098 false 1.33,3.853 1.33,4.025 false 1.19,3.839 1.085,4.123 false 1.048,3.84 0.861,4.046 false 0.938,3.838 0.623,3.878 false 1.782,3.815 2.188,3.815 false 5.568,1.717 6.541,1.920 0.973,0.202 10 DEFOG Relay: 5.149,2.286 5.334,2.468 0.185,0.181 10 1 6.579,3.903 6.743,4.096 0.164,0.193 10 2 6.757,2.318 6.898,2.483 0.141,0.165 10 4 6.825,3.069 6.991,3.260 0.166,0.191 10 5 4.771,3.06 4.938,3.221 0.167,0.161 10 3 5.266,2.361 5.52,2.361 5.52,2.361 5.999,2.784 false 6.084,3.137 6.509,2.4 6.509,2.4 6.683,2.4 false 6.417,3.137 6.774,3.137 false 5.708,3.137 4.922,3.137 false 5.999,3.509 6.403,3.976 6.403,3.976 6.524,3.976 false 0.157,0.999 1.058,1.183 0.902,0.184 10 High ← Low:

2.

After the low to high switch is complete, check the neutral position detection switch and limit switch.

(a)

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (N)* - 7 (GND) After low to high switch is complete 10 kΩ or higher
4 (HL1) - 7 (GND) After low to high switch is complete Below 1 Ω
5 (HL3) - 7 (GND) After low to high switch is complete 10 kΩ or higher
6 (HL2) - 7 (GND) After low to high switch is complete 10 kΩ or higher


*: for Manual Transmission

If there is a malfunction, replace the transfer shift actuator assembly.





Hide 36410J 8.INSPECT TRANSFER SHIFT ACTUATOR ASSEMBLY (CENTER DIFFERENTIAL LOCK ACTUATOR)

a.

Check the center differential lock actuator.

i.

Check the free to lock switch.

1.

Connect lines via a relay as shown in the illustration, and check that the actuator fork moves from the free to lock position.

NOTICE:
·

Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, make sure to operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the DEFOG relay.


C179846E07
1.01,3.604 0.573,3.677 true 1.146,3.604 0.948,3.802 true 1.292,3.594 1.229,3.885 true 1.542,3.604 1.729,3.917 true 1.688,3.604 1.938,3.75 true 1.844,3.531 2.135,3.531 true 5.948,2.792 5.417,2.438 5.417,2.438 5.292,2.438 true 6.01,3.135 6.552,2.406 6.552,2.406 6.677,2.406 true 6.344,3.135 6.677,3.135 true 5.938,3.521 6.583,3.771 6.583,3.771 6.698,3.771 true 5.656,3.146 5.052,3.146 true 0.625,0.25 3.229,0.708 2.604,0.458 10 false Component without harness connected: (Center Differential Lock Actuator) 0.646,1.063 1.74,1.25 1.094,0.188 10 false Free → Lock: 0.177,3.656 0.594,3.823 0.417,0.167 10 false GND1 0.75,3.844 1.104,4.021 0.354,0.177 10 false TL2 1.063,3.927 1.396,4.104 0.333,0.177 10 false TL3 1.688,3.958 1.99,4.125 0.302,0.167 10 false CDL 1.948,3.781 2.281,4 0.333,0.219 10 false TM2 2.167,3.479 2.594,3.708 0.427,0.229 10 false TM1 5.531,1.865 6.49,2.063 0.958,0.198 10 false DEFOG Relay: 5.198,2.375 5.333,2.542 0.135,0.167 10 false 1 6.76,3.698 6.896,3.865 0.135,0.167 10 false 2 4.927,3.083 5.063,3.271 0.135,0.188 10 false 3 6.75,2.344 6.927,2.51 0.177,0.167 10 false 4 6.719,3.073 6.885,3.292 0.167,0.219 10 false 5

2.

After the free to lock switch is complete, check the center differential lock detection switch and limit switch.

(a)

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (CDL) - 7 (GND1) After free to lock switch is complete Below 1 Ω
5 (TL3) - 7 (GND1) After free to lock switch is complete 10 kΩ or higher
6 (TL2) - 7 (GND1) After free to lock switch is complete Below 1 Ω


If there is a malfunction, replace the transfer shift actuator assembly.




ii.

Check the lock to free switch.

1.

Connect lines via a relay as shown in the illustration, and check that the actuator fork moves from the lock to free position.

NOTICE:
·

Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, make sure to operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the DEFOG relay.


C179847E07
0.958,3.74 0.646,3.813 true 1.104,3.74 0.896,3.938 true 1.25,3.729 1.177,4.021 true 1.5,3.75 1.677,4.052 true 1.646,3.74 1.885,3.885 true 1.792,3.698 2.083,3.698 true 5.958,2.802 5.427,2.458 5.427,2.458 5.302,2.458 true 6.021,3.125 6.563,2.396 6.563,2.396 6.688,2.396 true 6.354,3.125 6.688,3.125 true 5.948,3.51 6.594,3.76 6.594,3.76 6.708,3.76 true 5.667,3.156 5.063,3.156 true 0.25,0.229 2.948,0.677 2.698,0.448 10 false Component without harness connected: (Center Differential Lock Actuator) 0.26,3.823 0.74,3.99 0.479,0.167 10 false GND1 0.698,3.979 1.271,4.135 0.573,0.156 10 false TL2 1.01,4.073 1.385,4.26 0.375,0.188 10 false TL3 1.646,4.063 2.167,4.229 0.521,0.167 10 false CDL 1.885,3.906 2.5,4.156 0.615,0.25 10 false TM2 2.115,3.635 2.552,3.854 0.438,0.219 10 false TM1 5.49,1.823 6.583,2.063 1.094,0.24 10 false DEFOG Relay: 5.208,2.396 5.344,2.563 0.135,0.167 10 false 1 6.76,3.688 6.896,3.854 0.135,0.167 10 false 2 4.938,3.083 5.073,3.271 0.135,0.188 10 false 3 6.76,2.323 6.938,2.49 0.177,0.167 10 false 4 6.76,3.063 6.927,3.281 0.167,0.219 10 false 5 0.396,1.177 1.531,1.375 1.135,0.198 10 false Free ← Lock:

2.

After the lock to free switch is complete, check the center differential lock detection switch and limit switch.

(a)

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (CDL) - 7 (GND1) After lock to free switch is complete 10 kΩ or higher
5 (TL3) - 7 (GND1) After lock to free switch is complete Below 1 Ω
6 (TL2) - 7 (GND1) After lock to free switch is complete 10 kΩ or higher


If there is a malfunction, replace the transfer shift actuator assembly.





Hide 36410J 9.INSPECT TRANSFER SHIFT ACTUATOR ASSEMBLY (TEMPERATURE SENSOR) (w/ Temperature Sensor)

a.
C346026E01
0.979,0.771 1.219,1.365 1.219,1.365 1.365,1.365 true 0.719,0.771 1.042,1.656 1.042,1.656 1.188,1.656 true 0.094,0 0.344,0.25 0.25,0.25 10 false *a 1.24,1.563 1.719,1.813 0.479,0.25 10 false TGND 1.417,1.281 1.74,1.531 0.323,0.25 10 false TT

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (TT) - Body ground Always 10 kΩ or higher
2 (TGND) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Temperature Sensor)


b.

While warming the transfer shift actuator assembly, measure the resistance according to the value(s) in the table below.

Standard Resistance :
Tester Connection Temperature Specified Condition
1 (TT) - 2 (TGND) 10°C (50°F) 3.61 kΩ
20°C (68°F) 2.38 kΩ
30°C (86°F) 1.61 kΩ


If the result is not as specified, replace the transfer shift actuator assembly.