Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY
RM2660E _52 Drivetrain _052811 DRIVE SHAFT / PROPELLER SHAFT _0255343 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.

·

Do not allow brake fluid, front differential oil, gasoline, or battery fluid to contact the front axle inboard joint boot and front axle outboard joint boot, as the front axle inboard joint boot and front axle outboard joint boot may be damaged.



PROCEDURE

Hide 43403A 1.REMOVE FRONT AXLE INBOARD JOINT SET SETTING SHAFT SNAP RING

a.
C057543

Using a screwdriver, remove the snap ring from the inboard joint shaft.

CAUTION:

Do not damage the spline of the front axle inboard joint set LH.



Hide 43448B 2.DISCONNECT FRONT NO. 2 AXLE INBOARD JOINT BOOT SETTING CLAMP

a.
C205158

Using a screwdriver, release the staked part of the front No. 2 axle inboard joint boot setting clamp and disconnect the front No. 2 axle inboard joint boot setting clamp as shown in the illustration.


Hide 43448A 3.DISCONNECT FRONT NO. 1 AXLE INBOARD JOINT BOOT SETTING CLAMP

a.

Using a side cutter, cut the front No. 1 axle inboard joint boot setting clamp and disconnect it.


Hide 4.DISCONNECT FRONT AXLE INBOARD JOINT BOOT

a.

Disconnect the front axle inboard joint boot from the front axle inboard joint set LH.


Hide 43404 5.REMOVE FRONT AXLE INBOARD JOINT SET LH

a.

Remove any old grease from the front axle inboard joint set LH.


b.
U156140E01
1.515,1.056 1.108,0.385 false 0.702,0.274 0.886,0.450 0.184,0.177 10 *a

Place matchmarks on the front axle inboard joint set LH and outboard joint shaft.

Text in Illustration
*a Matchmark

NOTICE:

Do not use a punch to make the matchmarks.



c.

Remove the front axle inboard joint set LH from the outboard joint shaft.


d.
C115633E12
2.365,1.438 1.75,0.281 1.75,0.281 2.167,0.281 true 2.542,1.26 2,0.281 true 2.427,1.344 1.854,0.292 false 2.219,0.208 2.542,0.406 0.323,0.198 10 false *a

Place matchmarks on the outboard joint shaft, inner race and cage.

Text in Illustration
*a Matchmark

NOTICE:

Do not use a punch to make the matchmarks.



e.

Remove the 6 balls.


f.

Slide the cage to the outboard joint side.


g.
C307708E01
2.412,0.472 2.617,0.657 0.205,0.185 10 *a

Using a snap ring expander, remove the snap ring.

Text in Illustration
*a Outboard joint side


h.
C158393

Using a brass bar and hammer, remove the inner race.

NOTICE:

Do not damage the inner race.



i.

Remove the cage.


j.

Remove the front No. 2 axle inboard joint boot setting clamp and front No. 1 axle inboard joint boot setting clamp, front axle inboard joint boot from the outboard joint shaft.


Hide 43447A 6.DISCONNECT FRONT NO. 1 AXLE OUTBOARD JOINT BOOT SETTING CLAMP

a.

Using a side cutter, cut the front No. 1 axle outboard joint boot setting clamp and disconnect it.


Hide 43447B 7.DISCONNECT FRONT NO. 2 AXLE OUTBOARD JOINT BOOT SETTING CLAMP

HINT:

Use the same procedure described for the front No. 1 axle outboard joint boot setting clamp.


Hide 8.REMOVE FRONT AXLE OUTBOARD JOINT BOOT

a.

Remove any old grease from the front axle outboard joint boot.


b.

Remove the front No. 2 axle outboard joint boot setting clamp and front axle outboard joint boot, front No. 1 axle outboard joint boot setting clamp from the outboard joint shaft.


Hide 9.REMOVE DUST SEAL

C222937

a.

Using a screwdriver and a hammer, remove the dust seal.

NOTICE:

Do not drop the outboard joint shaft.



Hide 41336E 10.REMOVE FRONT DRIVE SHAFT DUST COVER LH

a.
C175797E01
0.97,0.726 0.806,0.379 0.806,0.379 0.592,0.379 false 0.204,0.294 0.558,0.459 0.353,0.164 10 SST 2.554,1.778 2.98,1.942 0.427,0.164

Using SST and a press, press out the front drive shaft dust cover LH.

SST
09950-00020  

NOTICE:

Do not drop the front axle inboard joint set LH.