Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY(w/ Differential Lock)
RM2660E _52 Drivetrain _052812 AXLE AND DIFFERENTIAL _0255353 REAR DIFFERENTIAL CARRIER ASSEMBLY(w/ Differential Lock) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY(w/ Differential Lock)  DISASSEMBLY  


PROCEDURE

Hide 41204 1.INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE REAR SUB-ASSEMBLY

a.
F001237E40
0.104,0.094 1.115,0.26 1.01,0.167 10 false Vertical Runout: 2.073,0.094 3.052,0.24 0.979,0.146 10 false Lateral Runout: 1.375,1.854 2.438,2.01 1.063,0.156 10 true 35 mm (1.38 in.)

Using a dial indicator, measure the vertical and lateral runout of the companion flange.

Maximum Runout:
Runout Specified Condition
Vertical runout 0.10 mm (0.00394 in.)
Lateral runout 0.10 mm (0.00394 in.)


If the runout is more than the maximum, replace the companion flange.


Hide 2.INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

a.
C161871

Using a dial indicator, measure the runout of the ring gear.

Maximum runout:

0.05 mm (0.00197 in.)


If the runout is more than the maximum, replace the ring gear with a new one.


Hide 3.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C161872

Using a dial indicator, measure the backlash of the ring gear.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)


HINT:

Measure at 3 or more positions around the circumference of the ring gear.


If the backlash is not as specified, adjust the side bearing preload or repair as necessary.


Hide 84222 4.REMOVE NO. 1 TRANSFER INDICATOR SWITCH

a.
C179875

Remove the switch and gasket.


Hide 41456 5.REMOVE REAR DIFFERENTIAL LOCK COVER

a.
C174253

Remove the 3 bolts.


b.

Using a brass bar and hammer, tap on the cover to remove it.


Hide 41450 6.REMOVE DIFFERENTIAL LOCK SHIFT ACTUATOR

a.
C161873

Remove the 4 bolts.


b.
C161874

Remove the shift fork shaft bolt.


c.

Using a screwdriver, pull out the actuator and remove the sleeve and shift fork.


Hide 41204G 7.REMOVE DRIVE PINION COMPANION FLANGE REAR NUT

a.
F044346E14
2.365,1.042 2.688,1.198 0.323,0.156 10 false SST

Using SST and a hammer, unstake the nut.

SST
09930-00010  


b.
C161836E02
2.275,0.629 2.5,0.47 2.5,0.47 2.645,0.472 false 2.686,0.382 3.023,0.540 0.336,0.158 10 SST

Using SST to hold the companion flange, remove the nut.

SST
09330-00021  (09330-00030)


Hide 41204 8.REMOVE REAR DRIVE PINION COMPANION FLANGE REAR SUB-ASSEMBLY

a.
C161837E02
1.024,0.594 1.178,0.594 1.178,0.594 1.472,0.757 false 0.648,0.506 0.969,0.677 0.321,0.171 10 SST

Using SST, remove the companion flange.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09956-03030)


Hide 41201C 9.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

a.
C162373E02
1.469,0.805 1.227,0.498 1.227,0.498 1.106,0.498 false 0.739,0.401 1.034,0.554 0.295,0.152 10 SST

Using SST, remove the oil seal.

SST
09308-10010  


Hide 41214 10.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41201B 11.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C124133E03
1.662,0.743 1.28,0.478 1.28,0.478 1.087,0.48 false 0.7,0.4 0.994,0.543 0.294,0.143 10 SST

Using SST, remove the bearing (inner race).

SST
09556-22010  

If the front bearing is damaged or worn, replace the bearing.


Hide 41302 12.REMOVE REAR DIFFERENTIAL CASE SUB-ASSEMBLY

a.
C161875E03
1.26,1.396 1.844,1.771 1.844,1.771 2.323,1.771 true 2.385,1.688 3.229,1.844 0.844,0.156 10 false Matchmark

Place matchmarks on the bearing caps and differential carrier.


b.

Remove the 4 bolts and 2 bearing caps.


c.
C161876E03
1.771,0.719 2.219,0.479 2.219,0.479 2.396,0.479 true 2.438,0.396 2.729,0.552 0.292,0.156 10 false SST

Using SST and a hammer, remove the plate washers.

SST
09504-22011  

HINT:

Measure the thickness of each plate washer and note it down.



d.
C164228E01
1.166,1.346 1.409,1.513 0.243,0.166 10 LH 2.567,1.338 2.809,1.504 0.243,0.166 10 RH

Remove the differential case with the side bearing (outer race) from the differential carrier.

HINT:

Tag the bearing outer races to show the location for reassembly.



Hide 13.REMOVE DIFFERENTIAL DRIVE PINION

Hide 41231 14.REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

Hide 41201A 15.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C116049E01
0.155,0.116 0.487,0.276 0.332,0.161 10 SST 0.545,0.202 0.817,0.202 false 0.817,0.202 0.817,1.011 false

Using SST and a press, press out the rear bearing (inner race) from the drive pinion.

SST
09950-00020  

If the drive pinion or ring gear is damaged, replaced them as a set.


Hide 41201D 16.REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER

Hide 41201B 17.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C161839

Using a brass bar and hammer, tap out the bearing (outer race).


Hide 41201A 18.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C162552

Using a brass bar and hammer, tap out the bearing (outer race).


Hide 19.REMOVE DIFFERENTIAL RING GEAR

a.
C161840E06
1.229,1.458 1.76,1.135 1.76,1.135 2.156,1.125 true 2.229,1.042 2.99,1.208 0.76,0.167 10 false Matchmark

Place matchmarks on the ring gear and differential case.


b.

Remove the 12 ring gear set bolts.


c.

Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.


Hide 20.INSPECT RUNOUT OF DIFFERENTIAL CASE

a.

Place the bearing outer races on their respective bearings.

HINT:

Do not interchange the left and right outer races.



b.

Install the assembled plate washers to the side bearing.


c.

Install the differential case to the differential carrier.

HINT:

If it is difficult to install the differential case to the carrier, replace the plate washer with a thinner one.


However, select a plate washer that allows no clearance between it and the carrier.


d.

Align the matchmarks on the bearing caps and differential carrier.


e.

Install and uniformly tighten the 4 bolts a little at a time.


f.
C161878

Using a dial indicator, measure the differential case runout.

Maximum case runout:

0.04 mm (0.00157 in.)


If the runout is more than the maximum, replace the differential case and side bearings as a set.


g.

Remove the differential case.


Hide 21.DISASSEMBLE DIFFERENTIAL CASE

a.
C161879E03
1.625,1.26 1.948,1.125 1.948,1.125 2.302,1.125 true 2.354,1.042 3.167,1.208 0.813,0.167 10 false Matchmark

Place matchmarks on the differential case and differential cover.


b.

Using a T10 "TORX" socket, remove the 5 set bolts and 3 pinion shaft pins.


c.

Separate the cover and case.


d.

Remove the 2 side gears, 2 side gear thrust washers, 4 pinion gears, 4 pinion gear thrust washers, 3 pinion shafts and holder from the differential case.


Hide 41301A 22.REMOVE REAR DIFFERENTIAL CASE BEARING

a.
C161880E03
2.313,0.583 1.979,0.583 1.979,0.583 1.792,0.729 true 1.583,1.021 2.146,0.583 true 2.344,0.5 2.698,0.656 0.354,0.156 10 false SST

Using SST, remove the side bearing.

SST
09950-40011  (09952-04010, 09953-04020, 09954-04010, 09955-04061)

HINT:

Fix the claws of SST to the notches in the differential case.



Hide 41301A 23.REMOVE REAR DIFFERENTIAL CASE BEARING

a.
C161881E03
1,0.885 0.823,0.677 0.823,0.677 0.521,0.677 true 0.938,1.063 0.646,0.688 true 0.177,0.625 0.51,0.781 0.333,0.156 10 false SST

Using SST, 4 bolts and a press, remove the bearing.

SST
09950-60010  (09951-00580)
09950-70010  (09951-07150)