Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY(for LSD)
RM2660E _52 Drivetrain _052812 AXLE AND DIFFERENTIAL _0255354 REAR DIFFERENTIAL CARRIER ASSEMBLY(for LSD) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY(for LSD)  DISASSEMBLY  


PROCEDURE

Hide 1.INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE

a.
F001237E40
0.104,0.094 1.115,0.26 1.01,0.167 10 false Vertical Runout: 2.073,0.094 3.052,0.24 0.979,0.146 10 false Lateral Runout: 1.375,1.854 2.438,2.01 1.063,0.156 10 true 35 mm (1.38 in.)

Using a dial indicator, measure the runout of the companion flange vertically and laterally.

Maximum Runout:
Runout Specified Condition
Vertical runout 0.10 mm (0.00394 in.)
Lateral runout 0.10 mm (0.00394 in.)


If the runout is more than the maximum, replace the companion flange.


Hide 2.INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

a.
C161834

Using a dial indicator, measure the ring gear runout.

Maximum runout:

0.05 mm (0.00197 in.)


If the runout is more than the maximum, replace the ring gear.


Hide 3.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C161902

Using a dial indicator, measure the ring gear backlash.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)


HINT:

Measure at 3 or more positions around the circumference of the ring gear.


If the backlash is not as specified, adjust the side bearing preload or repair as necessary.


Hide 41204G 4.REMOVE DRIVE PINION COMPANION FLANGE REAR NUT

a.
F044346E14
2.365,1.042 2.688,1.198 0.323,0.156 10 false SST

Using SST and a hammer, unstake the nut.

SST
09930-00010  


b.
C161836E02
2.275,0.629 2.5,0.47 2.5,0.47 2.645,0.472 false 2.686,0.382 3.023,0.540 0.336,0.158 10 SST

Using SST to hold the flange, remove the nut.

SST
09330-00021  (09330-00030)


Hide 41204 5.REMOVE REAR DRIVE PINION COMPANION FLANGE REAR SUB-ASSEMBLY

a.
C161837E02
1.024,0.594 1.178,0.594 1.178,0.594 1.472,0.757 false 0.648,0.506 0.969,0.677 0.321,0.171 10 SST

Using SST, remove the companion flange.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)


Hide 41201C 6.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

a.
C162373E02
1.469,0.805 1.227,0.498 1.227,0.498 1.106,0.498 false 0.739,0.401 1.034,0.554 0.295,0.152 10 SST

Using SST, remove the oil seal from the differential carrier.

SST
09308-10010  


Hide 41214 7.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41201B 8.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C124133E03
1.662,0.743 1.28,0.478 1.28,0.478 1.087,0.48 false 0.7,0.4 0.994,0.543 0.294,0.143 10 SST

Using SST, remove the front bearing (inner race) from the drive pinion.

SST
09556-22010  

If the front bearing is damaged or worn, replace the bearing.


Hide 41316 9.REMOVE REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK

a.
C161838

Remove the 2 bolts and 2 adjusting nut locks.


Hide 10.REMOVE DIFFERENTIAL CASE ASSEMBLY

a.
C161903E06
1,1.771 1.281,1.771 1.281,1.771 1.677,1.542 true 0.281,1.698 1.073,1.958 0.792,0.26 10 true Matchmark

Place matchmarks on the bearing caps and differential carrier.


b.

Remove the 4 bolts, 2 bearing caps, 2 adjusting nuts and 2 bearings (outer race).


c.
C161275E01
1.156,1.333 1.364,1.500 0.208,0.166 10 LH 2.54,1.329 2.765,1.495 0.225,0.166 10 RH

Remove the differential case from the differential carrier.

HINT:

Tag the 2 case bearing outer races to show the location for reassembly.



Hide 11.REMOVE DIFFERENTIAL DRIVE PINION

a.

Remove the differential drive pinion from the differential carrier.


Hide 41231 12.REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

Hide 41201A 13.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C116049E01
0.155,0.116 0.487,0.276 0.332,0.161 10 SST 0.545,0.202 0.817,0.202 false 0.817,0.202 0.817,1.011 false

Using SST and a press, press out the bearing (inner race).

SST
09950-00020  

If either the drive pinion or ring gear is damaged, replace them as a set.


Hide 41201D 14.REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER

Hide 41201B 15.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C161839

Using a brass bar and hammer, tap out the bearing (outer race).


Hide 41201A 16.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C162552

Using a brass bar and hammer, tap out the bearing (outer race).


Hide 17.REMOVE DIFFERENTIAL RING GEAR

a.
C161840E06
1.229,1.458 1.76,1.135 1.76,1.135 2.156,1.125 true 2.229,1.042 2.99,1.208 0.76,0.167 10 false Matchmark

Place matchmarks on the ring gear and differential case.


b.

Remove the 12 ring gear set bolts.


c.

Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.


Hide 18.INSPECT RUNOUT OF DIFFERENTIAL CASE

HINT:

If the ring gear runout is at the maximum or less (refer to the "Inspect Runout of Differential Ring Gear" procedure), this inspection is not necessary.


a.

Install the differential case to the differential carrier.


b.
C161841

Using a dial indicator, measure the differential case runout.

Maximum runout:

0.04 mm (0.00157 in.)


If the runout is more than the maximum, replace the differential case and side bearings as a set.


c.

Remove the differential case from the differential carrier.


Hide 41301A 19.REMOVE REAR DIFFERENTIAL CASE BEARING

a.
U156104E02
2.573,1.563 2.177,1.26 false 2.76,1.563 2.125,1.073 false 2.854,1.479 3.167,1.625 0.313,0.146 10 false SST

Using SST, remove the 2 side bearings (inner race) from the differential case.

SST
09950-00020  
09950-00030  
09950-40011  (09957-04010)
09950-60010  (09951-00480)


Hide 20.DISASSEMBLE DIFFERENTIAL CASE

a.
C161843E10
1.896,1.354 2.219,1 2.219,1 2.448,1 true 2.5,0.906 3.25,1.063 0.75,0.156 10 false Matchmark

Place matchmarks on the differential case LH and RH.


b.

Remove the 8 bolts uniformly, a little at a time.


c.

Using a plastic-faced hammer, separate the differential case LH and RH.


d.

Remove the 2 side gears, 6 side gear thrust washers, 4 clutch plates, 2 spring retainers, compression spring, 4 pinion gears, 4 pinion gear thrust washers and spider from the differential case.

HINT:
·

Keep the disassembled parts in order.

·

If the side gear backlash has been adjusted by a TOYOTA dealer, adjusting shims are installed between the side gear thrust washer and the differential case.



If replacing a side gear, also replace the thrust washer that contacts it.


Hide 41361 21.INSPECT REAR DIFFERENTIAL SIDE GEAR THRUST WASHER

HINT:

If replacing the thrust washer, also replace the clutch plate that contacts it.


a.
C161906

Using a micrometer, check that the thickness of the thrust washer is even.

Thickness (Reference):

1.97 to 2.06 mm (0.0776 to 0.0811 in.)


If necessary, replace the thrust washer.


b.

Visually check the thrust washer.

If bare metal is showing, replace the thrust washer.


Hide 41385 22.INSPECT CLUTCH PLATE

a.
C161907

Using a micrometer, check that the thickness of the clutch plate is even.

Thickness (Reference):

1.97 to 2.03 mm (0.0776 to 0.0799 in.)


If necessary, replace the clutch plate.


Hide 41331A 23.INSPECT COMPRESSION SPRING

a.
C161908

Using vernier caliper, measure the free length of the spring.

Length (Reference):

32.8 mm (1.29134 in.)


If necessary, replace the compression spring.