Home › Suspension › SUSPENSION CONTROL › ACTIVE HEIGHT CONTROL SUSPENSION › from 2015.08
RM2660E _53 Suspension _052813 SUSPENSION CONTROL _0255367 ACTIVE HEIGHT CONTROL SUSPENSION C

SUSPENSION CONTROL  ACTIVE HEIGHT CONTROL SUSPENSION  C1711  Front Height Control Sensor RH Circuit Malfunction  C1712  Front Height Control Sensor LH Circuit Malfunction  C1713  Rear Height Control Sensor RH Circuit Malfunction  C1714  Rear Height Control Sensor LH Circuit Malfunction  


DESCRIPTION

The height control sensor changes its resistance value based on changes in vehicle height. The suspension control ECU outputs a fixed voltage of 5 V to the SHB terminal of the height control sensor. If the sensor resistance value changes, the sensor voltage value changes accordingly. The suspension control ECU then receives the voltage value from the sensor to detect the vehicle height change.

DTC Code Detection Condition Trouble Area
C1711 When one of the following conditions is met:
·

With the engine switch on (IG), a voltage of 4.7 V or higher, or 0.3 V or less at the front height control sensor RH is detected for 1 second.

·

When there is a height control sensor power supply voltage malfunction.

·

When the height control sensor is determined to be stuck (When the sensor output is constant while the vehicle is turning, the sensor is determined to be stuck).


·

Harness or connector

·

Front height control sensor RH

·

Suspension control ECU


C1712 When one of the following conditions is met:
·

With the engine switch on (IG), a voltage of 4.7 V or higher, or 0.3 V or less at the front height control sensor LH is detected for 1 second.

·

When there is a height control sensor power supply voltage malfunction.

·

When the height control sensor is determined to be stuck (When the sensor output is constant while the vehicle is turning, the sensor is determined to be stuck).


·

Harness or connector

·

Front height control sensor LH

·

Suspension control ECU


C1713 When one of the following conditions is met:
·

With the engine switch on (IG), a voltage of 4.7 V or higher, or 0.3 V or less at the rear height control sensor RH is detected for 1 second.

·

When there is a height control sensor power supply voltage malfunction.

·

When the height control sensor is determined to be stuck (When the sensor output is constant while the vehicle is turning, the sensor is determined to be stuck).


·

Harness or connector

·

Rear height control sensor RH

·

Suspension control ECU


C1714 When one of the following conditions is met:
·

With the engine switch on (IG), a voltage of 4.7 V or higher, or 0.3 V or less at the rear height control sensor LH is detected for 1 second.

·

When there is a height control sensor power supply voltage malfunction.

·

When the height control sensor is determined to be stuck (When the sensor output is constant while the vehicle is turning, the sensor is determined to be stuck).


·

Harness or connector

·

Rear height control sensor LH

·

Suspension control ECU



WIRING DIAGRAM

F100744E18
5.427,8.01 7.042,8.219 1.615,0.208 10 false Suspension Control ECU 0.125,1.979 2.229,2.25 2.104,0.271 10 false Front Height Control Sensor RH 2.406,3.917 4.51,4.188 2.104,0.271 10 false Front Height Control Sensor LH 0.125,5.833 2.229,6.104 2.104,0.271 10 false Rear Height Control Sensor RH 2.146,7.896 4.25,8.167 2.104,0.271 10 false Rear Height Control Sensor LH 1.073,0.594 1.396,0.75 0.323,0.156 10 false SHG 1,1.073 1.396,1.219 0.396,0.146 10 false SHFR 1.083,1.531 1.396,1.677 0.313,0.146 10 false SHB 0.125,1.802 0.396,1.969 0.271,0.167 10 false z34 1.5,0.469 1.708,0.635 0.208,0.167 10 false 1 1.5,0.948 1.646,1.125 0.146,0.177 10 false 2 1.5,1.427 1.646,1.594 0.146,0.167 10 false 3 1.073,4.458 1.396,4.615 0.323,0.156 10 false SHB 0.99,4.958 1.406,5.104 0.417,0.146 10 false SHRR 1.083,5.417 1.458,5.563 0.375,0.146 10 false SHG 1.5,4.333 1.708,4.5 0.208,0.167 10 false 1 1.5,4.833 1.646,5.01 0.146,0.177 10 false 2 1.5,5.292 1.646,5.458 0.146,0.167 10 false 3 3.333,2.521 3.656,2.677 0.323,0.156 10 false SHG 3.26,3.021 3.656,3.167 0.396,0.146 10 false SHFL 3.344,3.479 3.656,3.625 0.313,0.146 10 false SHB 3.76,2.396 3.969,2.563 0.208,0.167 10 false 1 3.76,2.906 3.906,3.083 0.146,0.177 10 false 2 3.76,3.365 3.906,3.531 0.146,0.167 10 false 3 3.198,6.479 3.521,6.635 0.323,0.156 10 false SHB 3.125,6.979 3.521,7.125 0.396,0.146 10 false SHRL 3.208,7.438 3.594,7.583 0.385,0.146 10 false SHG 3.615,6.365 3.823,6.531 0.208,0.167 10 false 1 3.625,6.844 3.771,7.021 0.146,0.177 10 false 2 3.625,7.333 3.771,7.5 0.146,0.167 10 false 3 2.406,3.74 2.656,3.906 0.25,0.167 10 false z35 0.125,5.667 0.417,5.813 0.292,0.146 10 false N5 2.146,7.719 2.521,7.927 0.375,0.208 10 false N7 5.552,2.51 5.823,2.656 0.271,0.146 10 false K36 5.542,3.01 5.823,3.156 0.281,0.146 10 false K35 5.542,3.469 5.823,3.615 0.281,0.146 10 false K36 5.604,2.313 5.802,2.479 0.198,0.167 10 false 15 5.604,2.802 5.802,2.958 0.198,0.156 10 false 21 5.594,3.26 5.823,3.427 0.229,0.167 10 false 14 5.885,2.521 6.365,2.677 0.479,0.156 10 false SHG2 5.885,3.031 6.354,3.177 0.469,0.146 10 false SHFL 5.885,3.469 6.302,3.615 0.417,0.146 10 false SHB2 5.531,7.427 5.875,7.573 0.344,0.146 10 false K36 5.542,6.969 5.854,7.115 0.313,0.146 10 false K36 5.542,6.469 5.865,6.615 0.323,0.146 10 false K36 5.604,6.281 5.802,6.448 0.198,0.167 10 false 25 5.604,6.792 5.802,6.948 0.198,0.156 10 false 27 5.594,7.25 5.823,7.417 0.229,0.167 10 false 19 5.885,6.469 6.365,6.625 0.479,0.156 10 false SHB4 5.885,6.969 6.354,7.115 0.469,0.146 10 false SHRL 5.885,7.427 6.302,7.573 0.417,0.146 10 false SHG4 5.542,5.417 5.844,5.563 0.302,0.146 10 false K36 5.531,4.969 5.833,5.115 0.302,0.146 10 false K36 5.542,4.458 5.813,4.604 0.271,0.146 10 false K36 5.604,4.25 5.802,4.417 0.198,0.167 10 false 13 5.604,4.771 5.802,4.927 0.198,0.156 10 false 24 5.594,5.229 5.823,5.396 0.229,0.167 10 false 20 5.885,4.458 6.365,4.615 0.479,0.156 10 false SHB3 5.885,4.969 6.354,5.115 0.469,0.146 10 false SHRR 5.885,5.427 6.302,5.573 0.417,0.146 10 false SHG3 5.542,0.573 5.813,0.719 0.271,0.146 10 false K35 5.542,1.083 5.823,1.229 0.281,0.146 10 false K36 5.542,1.542 5.813,1.688 0.271,0.146 10 false K35 5.604,0.375 5.802,0.542 0.198,0.167 10 false 12 5.604,0.896 5.802,1.052 0.198,0.156 10 false 26 5.594,1.344 5.823,1.51 0.229,0.167 10 false 15 5.875,0.573 6.354,0.729 0.479,0.156 10 false SHG1 5.875,1.073 6.344,1.219 0.469,0.146 10 false SHFR 5.885,1.542 6.302,1.688 0.417,0.146 10 false SHB1

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing troubleshooting, inspect the connectors of related circuits.

·

If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed (See page Suspension>SUSPENSION CONTROL>ACTIVE HEIGHT CONTROL SUSPENSION>INITIALIZATION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (HEIGHT CONTROL SENSOR - SUSPENSION CONTROL ECU)
NOTICE:

When inspecting the wire harnesses between the suspension control ECU and each sensor, it is difficult to determine the malfunctioning area if there is a sensor power supply malfunction. Therefore, disconnect each sensor connector (front RH, front LH, rear RH and rear LH) on the ECU side.


a.

Check the front height control sensor RH side: (C1711)

i.

Disconnect the K35 and K36 ECU connectors.


ii.

Disconnect the z34 sensor connector.


iii.

Measure the resistance according to the value(s) in the table below.

U164780E02
5.771,1.677 5.771,2.208 true 1.396,2.104 0.573,2.26 0.573,2.26 0.573,2.323 true 2.063,2.083 1.833,2.302 1.833,2.302 1.833,2.365 true 2.198,2.083 3.052,2.302 3.052,2.302 3.052,2.365 true 5.594,1.667 4.927,2.115 4.927,2.115 4.927,2.208 true 5.938,1.677 6.521,2.094 6.521,2.094 6.521,2.26 true 1.219,0.083 3.531,0.49 2.313,0.406 10 false Rear view of wire harness connector: (to Suspension Control ECU) 4.552,0.135 6.958,0.656 2.406,0.521 10 false Front view of wire harness connector: (to Front Height Control Sensor RH) 4.917,1.5 5.229,1.719 0.313,0.219 10 false z34 4.802,2.25 5.302,2.427 0.5,0.177 10 false SHG 5.615,2.281 6.083,2.479 0.469,0.198 10 false SHFR 6.406,2.292 6.74,2.448 0.333,0.156 10 false SHB 1.51,2.417 2.229,2.625 0.719,0.208 10 false 15 (SHB1) 0.219,2.396 0.927,2.573 0.708,0.177 10 false 26 (SHFR) 2.76,2.427 3.448,2.573 0.688,0.146 10 false 12 (SHG1) 0.729,1.646 1.042,1.865 0.313,0.219 10 false K36 1.698,1.677 2,1.906 0.302,0.229 10 false K35

Standard Resistance:
Tester Connection Condition Specified Condition
z34-1 (SHG) - K35-12 (SHG1) Always Below 1 Ω
z34-2 (SHFR) - K36-26 (SHFR) Always Below 1 Ω
z34-3 (SHB) - K35-15 (SHB1) Always Below 1 Ω
z34-1 (SHG) - Body ground Always 10 kΩ or higher
z34-2 (SHFR) - Body ground Always 10 kΩ or higher
z34-3 (SHB) - Body ground Always 10 kΩ or higher




b.

Check the front height control sensor LH side: (C1712)

i.

Disconnect the K35 and K36 ECU connectors.


ii.

Disconnect the z35 sensor connector.


iii.

Measure the resistance according to the value(s) in the table below.

U164781E02
5.792,1.677 5.792,2.208 true 1.354,2.031 0.604,2.302 0.604,2.302 0.604,2.365 true 1.406,2.031 1.781,2.292 1.781,2.292 1.781,2.385 true 2.156,2.125 2.677,2.49 2.677,2.49 2.74,2.49 true 5.594,1.667 4.948,2.125 4.948,2.125 4.948,2.25 true 5.938,1.667 6.51,2.115 6.51,2.115 6.51,2.229 true 1.188,0.125 3.5,0.531 2.313,0.406 10 false Rear view of wire harness connector: (to Suspension Control ECU) 4.552,0.135 6.958,0.656 2.406,0.521 10 false Front view of wire harness connector: (to Front Height Control Sensor LH) 4.906,1.5 5.198,1.698 0.292,0.198 10 false z35 4.802,2.26 5.302,2.438 0.5,0.177 10 false SHG 5.615,2.24 6.083,2.438 0.469,0.198 10 false SHFL 6.406,2.25 6.74,2.406 0.333,0.156 10 false SHB 2.771,2.417 3.49,2.625 0.719,0.208 10 false 21 (SHFL) 0.719,1.656 1.031,1.844 0.313,0.188 10 false K36 1.688,1.677 2,1.875 0.313,0.198 10 false K35 1.448,2.438 2.156,2.583 0.708,0.146 10 false 14 (SHB2) 0.292,2.396 1,2.563 0.708,0.167 10 false 15 (SHG2)

Standard Resistance:
Tester Connection Condition Specified Condition
z35-1 (SHG) - K36-15 (SHG2) Always Below 1 Ω
z35-2 (SHFL) - K35-21 (SHFL) Always Below 1 Ω
z35-3 (SHB) - K36-14 (SHB2) Always Below 1 Ω
z35-1 (SHG) - Body ground Always 10 kΩ or higher
z35-2 (SHFL) - Body ground Always 10 kΩ or higher
z35-3 (SHB) - Body ground Always 10 kΩ or higher




c.

Check the rear height control sensor RH side: (C1713)

i.

Disconnect the K35 and K36 ECU connectors.


ii.

Disconnect the N5 sensor connector.


iii.

Measure the resistance according to the value(s) in the table below.

U164884E02
5.406,1.563 4.573,2.052 4.573,2.052 4.573,2.156 true 5.729,1.552 6.51,2.083 6.51,2.083 6.51,2.177 true 5.552,1.781 5.552,2.333 true 1.438,2.042 1.083,2.417 1.083,2.417 1.083,2.49 true 1.135,2.031 0.438,2.073 0.438,2.073 0.438,2.125 true 1.49,2.104 1.75,2.594 1.75,2.594 1.823,2.594 true 1.219,0.135 3.531,0.542 2.313,0.406 10 false Rear view of wire harness connector: (to Suspension Control ECU) 4.427,0.115 6.833,0.635 2.406,0.521 10 false Front view of wire harness connector: (to Rear Height Control Sensor RH) 4.698,1.219 5.01,1.448 0.313,0.229 10 false N5 5.427,2.323 5.813,2.5 0.385,0.177 10 false SHG 6.344,2.208 6.813,2.406 0.469,0.198 10 false SHRR 4.417,2.198 4.75,2.354 0.333,0.156 10 false SHB 0.677,1.656 0.969,1.844 0.292,0.188 10 false K36 1.667,1.656 2,1.865 0.333,0.208 10 false K35 0.083,2.156 0.792,2.302 0.708,0.146 10 false 20 (SHG3) 0.781,2.5 1.479,2.688 0.698,0.188 10 false 13 (SHB3) 1.854,2.521 2.646,2.698 0.792,0.177 10 false 24 (SHRR)

Standard Resistance:
Tester Connection Condition Specified Condition
N5-3 (SHG) - K36-20 (SHG3) Always Below 1 Ω
N5-2 (SHRR) - K36-24 (SHRR) Always Below 1 Ω
N5-1 (SHB) - K36-13 (SHB3) Always Below 1 Ω
N5-3 (SHG) - Body ground Always 10 kΩ or higher
N5-2 (SHRR) - Body ground Always 10 kΩ or higher
N5-1 (SHB) - Body ground Always 10 kΩ or higher




d.

Check the rear height control sensor LH side: (C1714)

i.

Disconnect the K35 and K36 ECU connectors.


ii.

Disconnect the N7 sensor connector.


iii.

Measure the resistance according to the value(s) in the table below.

U164885E02
5.406,1.594 4.573,2.083 4.573,2.083 4.573,2.188 true 5.729,1.563 6.51,2.094 6.51,2.094 6.51,2.188 true 5.563,1.792 5.563,2.344 true 1.188,2.042 0.438,2.073 0.438,2.073 0.438,2.125 true 1.448,2.094 1.75,2.583 1.75,2.583 1.823,2.583 true 1.188,2.104 1.094,2.406 1.094,2.406 1.094,2.49 true 1.219,0.135 3.531,0.542 2.313,0.406 10 false Rear view of wire harness connector: (to Suspension Control ECU) 4.427,0.125 6.833,0.646 2.406,0.521 10 false Front view of wire harness connector: (to Rear Height Control Sensor LH) 4.708,1.219 5.021,1.458 0.313,0.24 10 false N7 5.417,2.344 5.802,2.521 0.385,0.177 10 false SHG 6.323,2.229 6.792,2.427 0.469,0.198 10 false SHRL 4.417,2.229 4.75,2.385 0.333,0.156 10 false SHB 0.677,1.656 1.01,1.865 0.333,0.208 10 false K36 1.677,1.667 2.021,1.927 0.344,0.26 10 false K35 0.083,2.167 0.792,2.313 0.708,0.146 10 false 19 (SHG4) 0.781,2.531 1.479,2.719 0.698,0.188 10 false 27 (SHRL) 1.854,2.5 2.646,2.677 0.792,0.177 10 false 25 (SHB4)

Standard Resistance:
Tester Connection Condition Specified Condition
N7-3 (SHG) - K36-19 (SHG4) Always Below 1 Ω
N7-2 (SHRL) - K36-27 (SHRL) Always Below 1 Ω
N7-1 (SHB) - K36-25 (SHB4) Always Below 1 Ω
N7-3 (SHG) - Body ground Always 10 kΩ or higher
N7-2 (SHRL) - Body ground Always 10 kΩ or higher
N7-1 (SHB) - Body ground Always 10 kΩ or higher





OK

2.INSPECT HEIGHT CONTROL SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT HEIGHT CONTROL SENSOR
a.

Check the front height control sensor:

i.

Remove the front height control sensor RH or front height control sensor LH (See page Suspension>SUSPENSION CONTROL>HEIGHT CONTROL SENSOR (for Front Side)>REMOVAL).

NOTICE:

Do not drop the height control sensor. If it is dropped, replace it with a new one.

C172268E03
4.802,1.292 4.917,1.292 4.917,1.292 5.26,1.656 true 5.552,1.083 5.458,1.083 5.458,1.083 5.406,1.635 true 5.552,1.719 5.667,2.396 5.667,2.396 5.74,2.396 true 4.281,1.219 4.833,1.417 0.552,0.198 10 false 3 (SHB) 5.604,1 7.021,1.188 1.417,0.188 10 false 2 (SHFR*1, SHFL*2) 5.792,2.313 6.354,2.521 0.563,0.208 10 false 1 (SHG) 4.25,0.073 6.74,0.438 2.49,0.365 10 false Component without harness connected: (Front Height Control Sensor) 0.552,1.354 1.083,1.583 0.531,0.229 10 false Normal 2.073,2.438 2.615,2.635 0.542,0.198 10 false Max. HI 0.906,0.073 1.49,0.229 0.583,0.156 10 false Min. LO 0.135,2.031 0.844,2.219 0.708,0.188 10 false *1: for RH 0.135,2.333 0.792,2.521 0.656,0.188 10 false *2: for LH



ii.

Connect 3 1.5 V dry cell batteries in series.


iii.

Connect the positive (+) end of the batteries to terminal 3 (SHB) of the height control sensor and the negative (-) end of the batteries to terminal 1 (SHG). While slowly moving the sensor link up and down, measure the voltage between terminal 2 (SHFR*1 or SHFL*2) and terminal 1 (SHG).

NOTICE:

Do not apply a voltage of higher than 6 V.


HINT:

*1: for RH

*2: for LH



iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
2 (SHFR) - 1 (SHG) Max. HI Approx. 4.1 V
Normal Approx. 2.25 V
Min. LO Approx. 0.45 V

for LH
Tester Connection Condition Specified Condition
2 (SHFL) - 1 (SHG) Max. HI Approx. 4.1 V
Normal Approx. 2.25 V
Min. LO Approx. 0.45 V




b.

Check the rear height control sensor.

i.

Remove the rear height control sensor RH or rear height control sensor LH (See page Suspension>SUSPENSION CONTROL>HEIGHT CONTROL SENSOR (for Rear Side)>REMOVAL).

NOTICE:

Do not drop the height control sensor. If it is dropped, replace it with a new one.


C358237E01
6.156,1.708 6.281,1.115 6.281,1.115 6.375,1.115 true 6.375,2.24 6.281,2.24 6.281,2.24 6.073,1.854 true 5.594,1.208 5.719,1.208 5.719,1.208 5.938,1.677 true 0.573,0.135 1.219,0.354 0.646,0.219 10 false Min. LO 0.49,1.438 1.135,1.656 0.646,0.219 10 false Normal 0.25,2.115 0.896,2.333 0.646,0.219 10 false *1: for RH 0.271,2.406 0.917,2.625 0.646,0.219 10 false *2: for LH 2.021,2.448 2.667,2.667 0.646,0.219 10 false Max. HI 4.021,0.177 6.531,0.688 2.51,0.51 10 false Component without harness connected: (Rear Height Control Sensor) 4.292,1.115 5.688,1.375 1.396,0.26 10 false 2 (SHRR*1, SHRL*2) 6.396,1.021 7.042,1.24 0.646,0.219 10 false 1 (SHB) 6.417,2.167 7.063,2.385 0.646,0.219 10 false 3 (SHG)


ii.

Connect 3 1.5 V dry cell batteries in series.


iii.

Connect the positive (+) end of the batteries to terminal 1 (SHB) of the height control sensor and the negative (-) end of the batteries to terminal 3 (SHG). While slowly moving the sensor link up and down, measure the voltage between terminal 2 (SHRR*1 or SHRL*2) and terminal 3 (SHG).

NOTICE:

Do not apply a voltage of higher than 6 V.


HINT:

*1: for RH

*2: for LH



iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
2 (SHRR) - 3 (SHG) Max. HI Approx. 4.1 V
Normal Approx. 2.25 V
Min. LO Approx. 0.45 V

for LH
Tester Connection Condition Specified Condition
2 (SHRL) - 3 (SHG) Max. HI Approx. 4.1 V
Normal Approx. 2.25 V
Min. LO Approx. 0.45 V




Result
Result Proceed to
OK A
Front height control sensor RH malfunction B
Front height control sensor LH malfunction C
Rear height control sensor RH malfunction D
Rear height control sensor LH malfunction E


A

REPLACE SUSPENSION CONTROL ECU

B

REPLACE FRONT HEIGHT CONTROL SENSOR RH

C

REPLACE FRONT HEIGHT CONTROL SENSOR LH

D

REPLACE REAR HEIGHT CONTROL SENSOR RH

E

REPLACE REAR HEIGHT CONTROL SENSOR LH