Home › Suspension › SUSPENSION CONTROL › ACTIVE HEIGHT CONTROL SUSPENSION › from 2015.08
RM2660E _53 Suspension _052813 SUSPENSION CONTROL _0255367 ACTIVE HEIGHT CONTROL SUSPENSION C

SUSPENSION CONTROL  ACTIVE HEIGHT CONTROL SUSPENSION  C1756  Suspension Control Relay Malfunction  


DESCRIPTION

This relay is to supply the power source to the pump and motor. The relay stays on while the height control is operated.

DTC Code Detection Condition Trouble Area
C1756 When either of the following is detected:
·

With the suspension control relay not activated, an open signal of the suspension control relay is detected for 1 second or more.

·

With the suspension control relay activated, a short signal of the suspension control relay is detected 8 times successively.


·

Harness or connector

·

Suspension control relay (AHC)

·

Suspension control ECU



WIRING DIAGRAM

C165721E07
5.118,2.369 6.792,2.560 1.673,0.191 10 Suspension Control ECU 1.354,1.003 2.436,1.312 1.082,0.309 10 to Height Control Pump and Motor 1.685,1.948 2.568,2.117 0.883,0.170 10 from Battery 2.516,1.402 4.984,1.662 2.468,0.260 10 Suspension Control Relay (AHC) 4.04,0.543 4.182,0.722 0.142,0.179 10 1 2.81,0.543 2.980,0.704 0.170,0.161 10 2 5.118,2.202 5.399,2.357 0.281,0.155 10 K36 5.125,0.543 5.327,0.690 0.202,0.147 10 16 5.434,0.643 5.724,0.845 0.290,0.202 10 RC 2.805,0.904 2.921,1.081 0.116,0.176 10 3 4.052,0.904 4.206,1.063 0.154,0.158 10 5

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing troubleshooting, inspect the connectors of related circuits.

·

If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed (See page Suspension>SUSPENSION CONTROL>ACTIVE HEIGHT CONTROL SUSPENSION>INITIALIZATION).



PROCEDURE

1.INSPECT SUSPENSION CONTROL RELAY (AHC)
a.

Remove the suspension control relay (AHC) from the engine room relay block.


b.
C149624E03
1.283,0.718 1.439,0.874 0.156,0.156 10 5 0.225,1.286 0.381,1.442 0.156,0.156 10 2 0.24,0.722 0.396,0.877 0.156,0.156 10 3 1.289,1.274 1.445,1.429 0.156,0.156 10 1 3.167,0.968 3.323,1.124 0.156,0.156 10 5 1.969,1.701 2.125,1.857 0.156,0.156 10 2 1.393,0.974 1.549,1.130 0.156,0.156 10 3 2.699,0.245 2.854,0.400 0.156,0.156 10 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminal 1 and 2 10 kΩ or higher
Battery voltage is applied to terminal 1 and 2 Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - ENGINE ROOM RELAY BLOCK AND BODY GROUND)

NG

REPLACE SUSPENSION CONTROL RELAY (AHC)

2.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - ENGINE ROOM RELAY BLOCK AND BODY GROUND)
a.

Remove the suspension control relay (AHC) from the engine room relay block.


b.

Disconnect the K36 suspension control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K36-16 (RC) - Engine room relay block suspension control relay (AHC) terminal 1 Always Below 1 Ω
K36-16 (RC) or Engine room relay block suspension control relay (AHC) terminal 1 - Body ground Always 10 kΩ or higher
Engine room relay block suspension control relay (AHC) terminal 2 - Body ground Always Below 1 Ω




OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR