Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER
RM2660E _53 Suspension _052815 FRONT SUSPENSION _0255383 FRONT SHOCK ABSORBER A

FRONT SUSPENSION  FRONT SHOCK ABSORBER  REASSEMBLY  


PROCEDURE

Hide 48132 1.INSTALL FRONT COIL SPRING LH

C159782E02
0.115,0.613 0.414,0.758 0.3,0.145 10 SST 0.464,0.688 0.688,0.688 false 0.688,0.688 0.727,0.793 false

a.

Secure SST in a vise.

SST
09727-30021  (09727-00010, 09727-00021, 09727-00031)


b.
C275706E11
1.823,1.281 2.063,1.281 false 1.823,3.729 2.063,3.729 false 0.302,0.094 0.469,0.25 0.167,0.156 10 false *a 0.302,2.563 0.469,2.719 0.167,0.156 10 false *b 2.104,1.198 2.417,1.365 0.313,0.167 10 false SST 2.094,3.646 2.406,3.813 0.313,0.167 10 false SST

Attach the arm of SST to the diameter of the coil spring.

Text in Illustration
*a Correct
*b Incorrect

CAUTION:
·

Make sure that the coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.

·

Make sure that the claws of the hooks are securely attached.




c.

Using SST, compress the coil spring.

CAUTION:
·

If the coil spring bends during the compression, immediately stop the compression and reinstall SST.

·

Do not compress the spring until the coil springs contact each other.

·

Do not use an impact wrench.




d.
C155966E01
2.55,1.354 3.244,1.498 0.694,0.144 10 Lower End 2.733,0.415 2.832,1.079 false 2.832,1.079 2.832,1.339 false 0.104,1.045 0.418,1.198 0.314,0.153 10 SST 0.705,1.126 0.476,1.126 false

Install the coil spring to the shock absorber.

HINT:

Fit the lower end of the coil spring into the recess of the spring seat of the shock absorber.



Hide 48609 2.INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY LH

a.

Install the 2 cushions, 2 retainers and suspension support to the piston rod.


b.

Temporarily install a new front shock absorber nut to the suspension support.


c.

Position the suspension support as shown in the illustration.

C173244E05
1.5,1.302 0.885,1.302 true 1.802,0.469 1.802,0.344 1.802,0.344 2.344,0.344 false 1.865,0.927 1.865,0.708 1.865,0.708 2.698,0.708 true 2.458,1.104 2.031,1.104 2.031,1.104 1.938,1.24 true 5.198,2.104 5.198,1.969 5.198,1.969 5.917,1.969 true 4.333,1.958 5.073,1.958 5.073,1.958 5.146,1.802 true 5.26,0.479 5.26,0.344 5.26,0.344 6.271,0.344 false 4.99,1.281 4.635,1.281 false 0.104,1.198 1.031,1.552 0.927,0.354 10 false Suspension Support Bolt 1.521,0.063 2.125,0.25 0.604,0.188 10 false LH Side: 4.979,0.063 5.583,0.25 0.604,0.188 10 false RH Side: 2.396,0.271 3.74,0.458 1.344,0.188 10 false Absorber Bush Axis 3.375,0.865 3.802,1.042 0.427,0.177 10 false Front 1.271,0.5 1.604,0.688 0.333,0.188 10 false 50° 1.271,2.365 1.604,2.552 0.333,0.188 10 false 45° 2.146,2.365 2.479,2.552 0.333,0.188 10 false 45° 2.115,0.5 2.448,0.688 0.333,0.188 10 false 45° 2.521,1.031 3.25,1.406 0.729,0.375 10 false Coil Spring Lower End 2.76,0.635 4.104,0.823 1.344,0.188 10 false 20 mm (0.787 in.) 3.625,1.854 4.458,2.198 0.833,0.344 10 false Coil Spring Lower End 4.74,2.375 5.073,2.563 0.333,0.188 10 false 45° 5.656,2.375 5.99,2.563 0.333,0.188 10 false 50° 4.833,0.469 5.167,0.656 0.333,0.188 10 false 45° 5.573,0.479 5.906,0.667 0.333,0.188 10 false 45° 5.969,1.875 7.063,2.073 1.094,0.198 10 false 20 mm (0.787 in.) 3.854,1.177 4.677,1.552 0.823,0.375 10 false Suspension Support Bolt 6.323,0.271 7.042,0.604 0.719,0.333 10 false Absorber Bush Axis


d.

Remove SST.

NOTICE:

Do not use an impact wrench. It will damage the shock absorber rod.


HINT:

Release the coil spring while checking the position of the suspension support.



Hide 48680A 3.TIGHTEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.

Tighten the nut.

Torque:
65 N*m (575 kgf*cm, 48 ft.*lbf)