Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2015.08–2016.08
RM2660E _53 Suspension _052817 TIRE PRESSURE MONITORING _0255402 TIRE PRESSURE WARNING SYSTEM U

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  TERMINALS OF ECU  


CHECK TIRE PRESSURE WARNING ECU AND RECEIVER


a.
U165205E02
0.167,0 0.375,0.188 0.208,0.188 10 false *a 0.25,0.771 0.542,0.927 0.292,0.156 10 false L65 0.688,0.771 0.938,0.927 0.25,0.156 10 false *A 0.25,1.125 0.542,1.281 0.292,0.156 10 false L75 0.688,1.135 0.979,1.292 0.292,0.156 10 false *B

Disconnect the L65*1 or L75*2 tire pressure warning ECU and receiver connector and measure the voltage and resistance on the wire harness side.

*1: w/o Front Antenna

*2: w/ Front Antenna


Text in Illustration
*A w/o Front Antenna
*B w/ Front Antenna
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L65-1 (IG) - L65-12 (GND)*1
L75-1 (IG) - L75-12 (GND)*2
B - BR IG power source Engine switch on (IG) 10 to 16 V
L65-7 (+B) - L65-12 (GND)*1 R - BR Power supply (from battery) Always 10 to 16 V
L65-9 (CANH) - L65-10 (CANL)*1
L75-9 (CANH) - L75-10 (CANL)*2
R - W CAN communication line Engine switch off 54 to 69 Ω
L65-12 (GND) - Body ground*1
L75-12 (GND) - Body ground*2
BR - Body ground Ground Always Below 1 Ω

*1: w/o Front Antenna

*2: w/ Front Antenna



b.

Connect the L65*1 or L75*2 tire pressure warning ECU and receiver connector.

*1: w/o Front Antenna

*2: w/ Front Antenna



c.

Measure the voltage and resistance according to the value(s) in the table below. If the result is not as specified, the ECU may be malfunctioning.

HINT:

Measure the values on the wire harness side while the connector is connected.


U165786E02
4.729,0.688 5.021,0.844 0.292,0.156 10 false L65 5.115,0.688 5.365,0.844 0.25,0.156 10 false *A 4.729,0.979 5.021,1.135 0.292,0.156 10 false L75 5.115,0.99 5.406,1.146 0.292,0.156 10 false *B 1.458,0.156 1.708,0.313 0.25,0.156 10 false *a

Text in Illustration
*A w/o Front Antenna *B w/ Front Antenna
*a Component with harness connected
(Tire Pressure Warning ECU and Receiver)
- -

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L65-3 (CLSW) - L65-12 (GND)*1
L75-3 (CLSW) - L75-12 (GND)*2
W - BR Tire pressure warning reset switch
·

Engine switch on (IG)

·

Tire pressure warning reset switch on


Below 1.5 V
·

Engine switch on (IG)

·

Tire pressure warning reset switch off


8 to 15 V
L65-4 (RDA) - L65-12 (GND)*1
L75-4 (RDA2) - L75-12 (GND)*2
G - BR Output signals Engine switch on (IG) Pulse generation (see waveform 1)
L65-5 (PRG) - L65-12 (GND)*1
L75-5 (PRG2) - L75-12 (GND)*2
L - BR Input signals Engine switch on (IG) Pulse generation (see waveform 1)

*1: w/o Front Antenna

*2: w/ Front Antenna



d.
C240058E01
2.87,1.132 3.114,1.339 0.244,0.207 10 *b 0.103,0 0.310,0.216 0.207,0.216 10 *a

Using an oscilloscope, check waveform 1.

Text in Illustration
*a Example
*b GND

Waveform 1:
Item Contents
Terminal L65-4 (RDA) - L65-12 (GND)*1
L75-4 (RDA2) - L75-12 (GND)*2
L65-5 (PRG) - L65-12 (GND)*1
L75-5 (PRG2) - L75-12 (GND)*2
Tool setting 5 V/DIV, 50 μs./DIV.
Vehicle condition Engine switch on (IG)

*1: w/o Front Antenna

*2: w/ Front Antenna


HINT:

The waveform shown in the illustration is an example. If the tester displays a waveform that alternates between high and low, where high is a voltage that is between the IG power source voltage and a voltage 2.2 V lower than the IG power source voltage, and where low is a voltage of between 0 and 1.2 V, the ECU can be judged normal.