Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2015.08–2016.08
RM2660E _53 Suspension _052817 TIRE PRESSURE MONITORING _0255402 TIRE PRESSURE WARNING SYSTEM U

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


f.

According to the display on the GTS, read the Data List.

Tire Pressure Monitor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Mode Status Tire pressure warning system mode/
NORMAL or TEST
NORMAL: Normal mode
TEST: Test mode
-
Main Tire Number of main tire IDs to be registered/
4 or 5
5 displayed -
2nd Tire Number of 2nd tire IDs to be registered
4 or 5
5 displayed -
Initialization Switch Tire pressure warning reset switch/
ON or OFF
ON: Switch on
OFF: Switch off
-
Vehicle Speed Vehicle speed reading/
min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)
Actual vehicle speed Speed indicated on the combination meter assembly
Registered ID 1 Code Registered ID1 code/
min.: 0, max.: FFFFFFF*1
ID No. registered for transmitter ID1 displayed -
Registered ID 2 Code Registered ID2 code/
min.: 0, max.: FFFFFFF*1
ID No. registered for transmitter ID2 displayed -
Registered ID 3 Code Registered ID3 code/
min.: 0, max.: FFFFFFF*1
ID No. registered for transmitter ID3 displayed -
Registered ID 4 Code Registered ID4 code/
min.: 0, max.: FFFFFFF*1
ID No. registered for transmitter ID4 displayed -
Registered ID 5 Code Registered ID5 code/
min.: 0, max.: FFFFFFF*1
ID No. registered for transmitter ID5 displayed -
ID 1 Temperature in Tire ID1 temperature in tire/
min.: -40°C (-40°F), max.: 215°C (419°F)
Actual tire temperature If -40°C (-40°F) is displayed, data has not been received.
ID 2 Temperature in Tire ID2 temperature in tire/
min.: -40°C (-40°F), max.: 215°C (419°F)
Actual tire temperature If -40°C (-40°F) is displayed, data has not been received.
ID 3 Temperature in Tire ID3 temperature in tire/
min.: -40°C (-40°F), max.: 215°C (419°F)
Actual tire temperature If -40°C (-40°F) is displayed, data has not been received.
ID 4 Temperature in Tire ID4 temperature in tire/
min.: -40°C (-40°F), max.: 215°C (419°F)
Actual tire temperature If -40°C (-40°F) is displayed, data has not been received.
ID 5 Temperature in Tire ID5 temperature in tire/
min.: -40°C (-40°F), max.: 215°C (419°F)
Actual tire temperature If -40°C (-40°F) is displayed, data has not been received.
Initialization Switch Info Tire pressure warning reset switch setting information/
WITH or WITHOUT
WITH -
ID 1 Tire Inflation Pressure ID1 tire inflation pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*2
ID 2 Tire Inflation Pressure ID2 tire inflation pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*2
ID 3 Tire Inflation Pressure ID3 tire inflation pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*2
ID 4 Tire Inflation Pressure ID4 tire inflation pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*2
ID 5 Tire Inflation Pressure ID5 tire inflation pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*2
Threshold of Low pressure (Lower Limit) Tire inflation pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Specified tire pressure warning threshold lower limit displayed If N/A is displayed, data has not been received.*2
ID 1 Initial Threshold of Low-pressure ID1 initial threshold of low-pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Initial threshold of low pressure If N/A is displayed, data has not been received.*2
ID 2 Initial Threshold of Low-pressure ID2 initial threshold of low-pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Initial threshold of low pressure If N/A is displayed, data has not been received.*2
ID 3 Initial Threshold of Low-pressure ID3 initial threshold of low-pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Initial threshold of low pressure If N/A is displayed, data has not been received.*2
ID 4 Initial Threshold of Low-pressure ID4 initial threshold of low-pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Initial threshold of low pressure If N/A is displayed, data has not been received.*2
ID 5 Initial Threshold of Low-pressure ID5 initial threshold of low-pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Initial threshold of low pressure If N/A is displayed, data has not been received.*2
Sensor ID Status Status of ID selection/
Main or 2nd
Status of ID selection -
Sensor ID Switch Function Information on whether there is ID switching function or not/
Without or With
Without: ID switching function is not equipped
With: ID switching function is equipped
-
ID 1 Tire Position ID1 Tire Position/No Information or FL or FR or RL or RR or Spare or Judging ID1 tire position is displayed If no tire position information is stored, "No Information" will be displayed.
ID 2 Tire Position ID2 Tire Position/No Information or FL or FR or RL or RR or Spare or Judging ID2 tire position is displayed If no tire position information is stored, "No Information" will be displayed.
ID 3 Tire Position ID3 Tire Position/No Information or FL or FR or RL or RR or Spare or Judging ID3 tire position is displayed If no tire position information is stored, "No Information" will be displayed.
ID 4 Tire Position ID4 Tire Position/No Information or FL or FR or RL or RR or Spare or Judging ID4 tire position is displayed If no tire position information is stored, "No Information" will be displayed.
ID 5 Tire Position ID5 Tire Position/No Information or FL or FR or RL or RR or Spare or Judging ID5 tire position is displayed If no tire position information is stored, "No Information" will be displayed.
ID 1 - FL Wheel Speed Synchronization Count ID1 - FL Wheel Speed Synchronization Count/min.: 0, max.: 255 Actual Synchronization Count -
ID 1 - FR Wheel Speed Synchronization Count ID1 - FR Wheel Speed Synchronization Count/min.: 0, max.: 255 Actual Synchronization Count -
ID 1 - RL Wheel Speed Synchronization Count ID1 - RL Wheel Speed Synchronization Count/min.: 0, max.: 255 Actual Synchronization Count -
ID 1 - RR Wheel Speed Synchronization Count ID1 - RR Wheel Speed Synchronization Count/min.: 0, max.: 255 Actual Synchronization Count -
ID 2 - FL Wheel Speed Synchronization Count ID2 - FL Wheel Speed Synchronization Count/min.: 0, max.: 255 Actual Synchronization Count -
ID 2 - FR Wheel Speed Synchronization Count ID2 - FR Wheel Speed Synchronization Count/min.: 0, max.: 255 Actual Synchronization Count -
ID 2 - RL Wheel Speed Synchronization Count ID2 - RL Wheel Speed Synchronization Count/min.: 0, max.: 255 Actual Synchronization Count -
ID 2 - RR Wheel Speed Synchronization Count ID2 - RR Wheel Speed Synchronization Count/min.: 0, max.: 255 Actual Synchronization Count -
ID 3 - FL Wheel Speed Synchronization Count ID3 - FL Wheel Speed Synchronization Count/min.: 0, max.: 255 Actual Synchronization Count -
ID 3 - FR Wheel Speed Synchronization Count ID3 - FR Wheel Speed Synchronization Count/min.: 0, max.: 255 Actual Synchronization Count -
ID 3 - RL Wheel Speed Synchronization Count ID3 - RL Wheel Speed Synchronization Count/min.: 0, max.: 255 Actual Synchronization Count -
ID 3 - RR Wheel Speed Synchronization Count ID3 - RR Wheel Speed Synchronization Count/min.: 0, max.: 255 Actual Synchronization Count -
ID 4 - FL Wheel Speed Synchronization Count ID4 - FL Wheel Speed Synchronization Count/min.: 0, max.: 255 Actual Synchronization Count -
ID 4 - FR Wheel Speed Synchronization Count ID4 - FR Wheel Speed Synchronization Count/min.: 0, max.: 255 Actual Synchronization Count -
ID 4 - RL Wheel Speed Synchronization Count ID4 - RL Wheel Speed Synchronization Count/min.: 0, max.: 255 Actual Synchronization Count -
ID 4 - RR Wheel Speed Synchronization Count ID4 - RR Wheel Speed Synchronization Count/min.: 0, max.: 255 Actual Synchronization Count -
ID 5 - FL Wheel Speed Synchronization Count ID5 - FL Wheel Speed Synchronization Count/min.: 0, max.: 255 Actual Synchronization Count -
ID 5 - FR Wheel Speed Synchronization Count ID5 - FR Wheel Speed Synchronization Count/min.: 0, max.: 255 Actual Synchronization Count -
ID 5 - RL Wheel Speed Synchronization Count ID5 - RL Wheel Speed Synchronization Count/min.: 0, max.: 255 Actual Synchronization Count -
ID 5 - RR Wheel Speed Synchronization Count ID5 - RR Wheel Speed Synchronization Count/min.: 0, max.: 255 Actual Synchronization Count -
Number of Trouble Code Number of DTCs recorded/min.: 0, max.: 255 Min.: 0, Max.: - -

HINT:

*1: Displayed only when the ID No. is not registered.

*2: It may take a few minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2125/25) (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>C2121/21).




PERFORM ACTIVE TEST


Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


f.

Perform the Active Test according to the display on the GTS.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Indicat. Tire Pressure Warning System Tire pressure warning light ON or OFF Perform the test with the vehicle stopped and engine idling.