Home › Suspension › TIRE / WHEEL › TIRE AND WHEEL SYSTEM › 2014.08–2015.08
RM2660E _53 Suspension _052818 TIRE / WHEEL _0255404 TIRE AND WHEEL SYSTEM G

TIRE / WHEEL  TIRE AND WHEEL SYSTEM  INSPECTION  


PROCEDURE

Hide 1.INSPECT TIRES

a.

Check the tires for wear and proper inflation pressure.

Standard Cold Tire Inflation Pressure:
Tire Size Destination Front
kPa (kgf/cm2, psi)
Rear
kPa (kgf/cm2, psi)
245/75R17 Middle East 230 (2.3, 33) 230 (2.3, 33)
260 (2.6, 38)*1
General Export 230 (2.3, 33) 230 (2.3, 33)
260 (2.6, 38)*1
285/65R17 Middle East 230 (2.3, 33) 230 (2.3, 33)
Australia 230 (2.3, 33) 230 (2.3, 33)
General Export 230 (2.3, 33) 230 (2.3, 33)
Europe 240 (2.4, 35) 240 (2.4, 35)
China 240 (2.4, 35) 240 (2.4, 35)
285/60R18 Middle East 230 (2.3, 33) 230 (2.3, 33)
Australia 230 (2.3, 33) 230 (2.3, 33)
General Export 230 (2.3, 33) 230 (2.3, 33)
Europe 240 (2.4, 35) 240 (2.4, 35)
China 240 (2.4, 35) 240 (2.4, 35)
285/50R20 Europe 240 (2.4, 35) 240 (2.4, 35)
260 (2.6, 38)*1


*1: For driving at 160 km/h (100 mph) or over


b.
R003031

Using a dial indicator, check the tire runout.

Tire runout:

3.0 mm (0.118 in.) or less



Hide 2.ROTATE TIRES

a.
C163157E04
0.552,0.208 0.719,0.396 0.167,0.188 10 false *a

Rotate the tires as shown in the illustration.

Torque:
for Aluminum Wheel : 131 N*m (1336 kgf*cm, 97 ft.*lbf)
for Steel Wheel : 209 N*m (2131 kgf*cm, 154 ft.*lbf)

Text in Illustration
*a Front of the Vehicle


Hide 3.INSPECT WHEEL BALANCE

a.
C144019

for Steel Wheel Type:

Check and adjust the off-the-car balance.

Standard Imbalance After Adjustment:

12 g (0.0265 lb) or less


HINT:

If necessary, check and adjust the on-the-car balance.



b.

for Aluminum Wheel Type:

Check and adjust the off-the-car balance.

Tire Size Standard Imbalance After Adjustment
285/65R17 7.5 g (0.0165 lb) or less
285/60R18 7.0 g (0.0154 lb) or less
285/50R20 6.5 g (0.0143 lb) or less

C241067E02
0.675,0.215 0.891,0.398 0.216,0.184 10 *a 4.364,0.215 4.580,0.398 0.216,0.184 10 *b 1.013,2.922 1.155,3.106 0.142,0.184 10 A 4.607,2.943 4.749,3.127 0.142,0.184 10 A 5.868,2.964 6.010,3.148 0.142,0.184 10 A

Text in Illustration
*a for 17 Inch Wheels *b for 18 Inch or 20 Inch Wheels

NOTICE:
·

Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be attached.

·

Do not touch the adhesive surface of the tape.

·

Attach a sticking-type balance weight to the flat surface (A) shown in the illustration.

Width (A):

20 mm (0.787 in.)


·

Push the balance weight firmly so that it securely adheres to the position.

·

Do not reuse the balance weight.



HINT:
·

For 17 inch wheels, the outer side balance weight should be installed by clipping it to the rim.

·

If necessary, check and adjust the on-the-car balance.