Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › REAR SPEED SENSOR › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255407 REAR SPEED SENSOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  REAR SPEED SENSOR  INSTALLATION  


PROCEDURE

Hide 89546 1.INSTALL REAR SPEED SENSOR LH

a.
C170903

Install the speed sensor with the nut.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)

NOTICE:
·

Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

·

While inserting the speed sensor into the knuckle hole, do not strike or damage the sensor tip.

·

After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the knuckle.

·

Make sure there is no foreign matter attached to the speed sensor rotor.




Hide 89545 2.INSTALL REAR SPEED SENSOR RH

a.
C170902

Install the speed sensor with the nut.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)

NOTICE:
·

Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

·

While inserting the speed sensor into the knuckle hole, do not strike or damage the sensor tip.

·

After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the knuckle.

·

Make sure there is no foreign matter attached to the speed sensor rotor.




Hide 89516B 3.INSTALL SKID CONTROL SENSOR WIRE

a.
U156119

Install the sensor clamp with the bolt.

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

Make sure the clamp rotation stopper touches the installation position.



b.

Connect the connector.

NOTICE:
·

Securely insert the connector.

·

When connecting the connector, do not twist the wire harness.




c.
U156118

Install the sensor clamp with the bolt.

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

Make sure the clamp rotation stopper touches the installation position.



d.
C170895

Connect the speed sensor RH connector.

NOTICE:
·

Securely connect the connector.

·

When connecting the connector, do not twist the wire harness.




e.

Attach the 3 clamps.

C170898

NOTICE:
·

When attaching the clamps, do not twist the wire harness.

·

When attaching the clamps, securely insert them as shown in the illustration.




f.

Attach the 5 clamps.

C170897

NOTICE:
·

When attaching the clamps, do not twist the wire harness.

·

When attaching the clamps, securely insert them as shown in the illustration.




g.

Attach the 2 clamps, and install the sensor clamp with the bolt.

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)

C170896


h.
C170899

Connect the speed sensor LH connector.

NOTICE:
·

Securely connect the connector.

·

When connecting the connector, do not twist the wire harness.




Hide 42603 4.INSTALL REAR WHEEL

Torque:
for Aluminum Wheel : 131 N*m (1336 kgf*cm, 97 ft.*lbf)
for Steel Wheel : 209 N*m (2131 kgf*cm, 154 ft.*lbf)

Hide 28800 5.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 89546 6.CHECK SPEED SENSOR SIGNAL