The skid control ECU (master cylinder solenoid) acquires steering sensor zero point every time the ignition switch is turned to ON and the vehicle is driven at 35 km/h (22 mph) or more for approximately 5 seconds. The ECU also stores the previous zero point.
The steering sensor zero point malfunction warning is canceled by turning the ignition switch off.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1439 | After the steering sensor zero point calibration is cleared due to, for example, fluctuations in the power source, the steering sensor zero point calibration cannot be obtained for 0.048 seconds of continuous driving. | ·
Steering sensor ·
Yaw rate and acceleration sensor (Airbag sensor assembly) ·
Skid control ECU (Master cylinder solenoid) |
| C1445 | Steering sensor zero point calibration cannot be obtained when the vehicle is driven without a record of steering sensor zero point calibration at a speed of 35 km/h (22 mph) or more for 30 seconds or more without the brake pedal being depressed. |
Before proceeding with the inspection, explain to the customer that the output DTC is related to temporary loss of the steering sensor zero point calibration, such as when the power voltage drops when the battery is removed, and confirm that this condition occurred.
After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
When the speed sensor or the yaw rate and acceleration sensor (airbag sensor assembly) has trouble, DTCs for the steering sensor may be stored even when the steering sensor is normal. When DTCs for the speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) are output together with other DTCs for the steering sensor, inspect and repair the speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) first, and then inspect and repair the steering sensor.
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON again and check that no CAN communication system DTC is output.
Drive the vehicle at a speed of 35 km/h (22 mph) and turn the steering wheel to the right and left, and then check that no speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to | |
|---|---|---|
| DTC is output | C1439 and/or C1445 | A |
| Relating to CAN communication system | B | |
| Relating to speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) | C | |
| DTC is not output | D | |
For the CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING), refer to the following:
for LHD (with Central Gateway ECU): See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
for LHD (without Central Gateway ECU): See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD (with Central Gateway ECU): See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD (without Central Gateway ECU): See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
If there is a malfunction in the speed sensor or the yaw rate and acceleration sensor (airbag sensor assembly), an abnormal value may be output although the steering sensor is normal.
If the speed sensor and the yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output simultaneously, repair the sensors and inspect the steering sensor.
If DTC C1439 and/or C1445 is not output again, the DTC may have been stored due to a temporary loss of the steering sensor zero point calibration, such as when the power voltage drops.
A
B
C
D
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for at least 5 seconds.
Check that the centered position of the steering wheel is correctly set while driving straight ahead.
If the front wheel alignment and steering position are adjusted as a result of an abnormal centered position of the steering wheel, acquire the yaw rate and acceleration sensor zero point again after the adjustments are completed.
The centered position of the steering wheel is correctly set.
OK
NG
Clear the DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 35 km/h (22 mph) or more and turn the steering wheel to the right and left.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1439 and C1445 are not output | A |
| Yaw rate and acceleration sensor (airbag sensor assembly) and/or steering sensor DTC is output | B |
If the same DTC C1439 and/or C1445 is not output again, the DTC may have been stored due to a temporary loss of the steering sensor zero point calibration, such as when the power voltage drops.
A
B