Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2015.08–2017.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255416 ANTI-LOCK BRAKE SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  TERMINALS OF ECU  


TERMINALS OF ECU


C140176E15
0.167,0.094 0.385,0.313 0.219,0.219 10 false *a

Text in Illustration
*a Component without harness connected
(Skid Control ECU [Master Cylinder Solenoid])
- -

Terminal No. (Symbol) Terminal Description
1 (GND1) Skid control ECU (Master cylinder solenoid) ground
2 (+BM1) Power supply for motor
3 (FR+) Front speed sensor RH power supply output
4 (FL-) Front speed sensor LH input
5 (RR+) Rear speed sensor RH power supply output
6 (RL-) Rear speed sensor LH input
7 (STP) Stop light switch assembly
11 (CANH) CAN communication terminal H
12 (SP1) Speedometer signal
14 (P) Rear differential lock detection switch (No. 1 Transfer indicator switch)
17 (FR-) Front speed sensor RH input
18 (FL+) Front speed sensor LH power supply output
19 (RR-) Rear speed sensor RH input
20 (RL+) Rear speed sensor LH power supply output
22 (VGS) Deceleration sensor power supply output
23 (GGND) Deceleration sensor ground
24 (TS) Sensor test terminal (Signal check switch)
25 (CANL) CAN communication terminal L
27 (EXI) Center differential lock detection switch (Transfer shift actuator assembly)
31 (+BS) Power supply for solenoid
32 (GND2) Skid control ECU (Master cylinder solenoid) ground
39 (GL1) Deceleration sensor input
41 (LBL) Brake fluid level warning switch (Brake master cylinder reservoir sub-assembly)
46 (IG1) IG1 power supply

C172937E04
0.35,0.012 0.582,0.195 0.232,0.184 10 *a

Text in Illustration
*a Component without harness connected
(Skid Control ECU [Master Cylinder Solenoid])
- -

Terminal No. (Symbol) Terminal Description
1 (IG2) IG2 power supply
2 (+BM2) Power supply for motor
4 (GND3) Skid control ECU (Master cylinder solenoid) ground


TERMINAL INSPECTION


Disconnect the connector and measure the voltage or resistance on the wire harness side.

HINT:

Voltage cannot be measured with the connector connected to the skid control ECU (master cylinder solenoid) as the connector is watertight.


U156143E04
0.458,1.625 0.729,1.802 0.271,0.177 10 false A24 4.698,1.625 4.969,1.802 0.271,0.177 10 false A25 0.313,0.198 0.75,0.51 0.438,0.313 10 false *a

Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])
- -

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A24-2 (+BM1) - Body ground B Power supply for motor
(From battery)
Always 11 to 14 V
A24-7 (STP) - Body ground R Stop light switch assembly Brake pedal depressed → released 8 to 14 V → Below 1.5 V
A24-31 (+BS) - Body ground W Power supply for solenoid
(From battery)
Always 11 to 14 V
A24-41 (LBL) - Body ground P Brake fluid level warning switch (Brake master cylinder reservoir sub-assembly) Brake fluid level +/-5 mm (+/-0.197 in.) from the minimum level → maximum level Below 1 Ω → 1.9 to 2.1 kΩ
A24-46 (IG1) - Body ground V IG1 power supply Ignition switch off → ON Below 1 V → 11 to 14 V
A25-1 (IG2) - Body ground B IG2 power supply Ignition switch off → ON Below 1 V → 11 to 14 V
A25-2 (+BM2) - Body ground B Power supply for motor
(From battery)
Always 11 to 14 V
A24-1 (GND1) - Body ground W-B Ground Always Below 1 Ω
A24-32 (GND2) - Body ground W-B Ground Always Below 1 Ω
A25-4 (GND3) - Body ground W-B Ground Always Below 1 Ω