Home › Brake › BRAKE SYSTEM (OTHER) › HYDRAULIC BRAKE BOOSTER(for LHD)
RM2660E _54 Brake _052820 BRAKE SYSTEM (OTHER) _0255426 HYDRAULIC BRAKE BOOSTER(for LHD) A

BRAKE SYSTEM (OTHER)  HYDRAULIC BRAKE BOOSTER(for LHD)  DISASSEMBLY  


PROCEDURE

Hide 44591A 1.REMOVE NO. 1 BRAKE ACTUATOR BRACKET

a.
C172196

Using a 5 mm hexagon wrench, remove the bolt and No. 1 brake actuator bracket.


b.
F051180

Using a screwdriver, disconnect the brake fluid level warning switch connector from the No. 1 brake actuator bracket.


Hide 47202 2.REMOVE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

a.
C172197E01
0.354,1.631 1.017,1.789 0.663,0.158 10 Pin Punch 1.705,1.219 1.35,1.729 1.35,1.729 1.163,1.729 false

Using a pin punch and hammer, remove the pin from the brake master cylinder reservoir.


b.
C172198

Remove the screw and pull out the brake master cylinder reservoir sub-assembly.


c.

Remove the master cylinder reservoir filler cap.


Hide 47255 3.REMOVE MASTER CYLINDER RESERVOIR GROMMET

a.
C172199

Remove the 3 reservoir grommets from the master cylinder reservoir.


Hide 44571A 4.REMOVE NO. 1 BRAKE ACTUATOR HOSE

a.
C172887

Using needle nose pliers, slide the 2 clips and remove the brake actuator hose and 2 clips.


Hide 44551C 5.REMOVE NO. 1 BRAKE ACTUATOR TUBE

a.
C172888E01
1.469,0.604 2.646,0.773 1.177,0.170 10 Union Nut Wrench 0.98,0.984 1.288,0.677 1.288,0.677 1.447,0.677 false

Using a union nut wrench, remove the No. 1 brake actuator tube.


Hide 47070B 6.REMOVE BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY

a.
U116675

Using a screwdriver, remove the 2 plugs.


b.
U116676

Remove the 2 screws and disconnect the wire harnesses from the master cylinder solenoid.


c.
F051187

Using a screwdriver, remove the clip.


d.
U157357

Remove the brake booster with accumulator pump assembly from the brake master cylinder.


e.

Remove the 2 brake booster pump collars and 2 brake booster pump bushes from the brake booster with accumulator pump assembly.


f.
U116681

Using a 4 mm hexagon wrench, remove the 2 pins.


Hide 47967A 7.REMOVE NO. 1 BRAKE BOOSTER PUMP BRACKET

a.
U116678

Using a 5 mm hexagon wrench, remove the 2 bolts and No. 1 brake booster pump bracket from the brake master cylinder solenoid.


b.

Remove the brake booster pump bush from the No. 1 brake booster pump bracket.


Hide 47955A 8.REMOVE BRAKE BOOSTER ACCUMULATOR PIPE

a.
C172891

Secure the brake booster with accumulator pump assembly in a vise.


b.

Remove the brake booster accumulator.


c.

Remove the O-ring from the brake booster accumulator.

NOTICE:

Ensure no foreign matter enters the pump.



d.

Remove the brake booster accumulator pipe and compression spring.


Hide 47217 9.REMOVE MASTER CYLINDER SOLENOID

a.
U116680

Remove the 6 bolts and master cylinder solenoid.


b.
F051196

Remove the gasket.


Hide 47264 10.REMOVE MASTER CYLINDER PUSH ROD CLEVIS

a.
C177091

Loosen the lock nut on the rod operating adapter, and remove the push rod clevis and lock nut.


b.
U116679

Loosen the lock nut on the brake master cylinder side, and remove the rod operating adapter and lock nut.


Hide 47265 11.REMOVE MASTER CYLINDER BOOT

Hide 12.REMOVE BRAKE BOOSTER PISTON SUB-ASSEMBLY

a.
F051417E13
1.979,1.823 2.25,1.896 false 1.792,0.906 1.646,0.781 1.646,0.781 1.49,0.781 false 2.271,1.823 2.792,2 0.521,0.177 10 false Pin 0.927,0.677 1.406,0.854 0.479,0.177 10 false C-Ring

Pressing the piston in with a screwdriver, insert a pin or equivalent from the hole in the master cylinder body to hold the C-ring, and then remove it with another screwdriver.

HINT:

Tape the screwdriver tip before use.



b.

Remove the plug from the piston.


c.

Remove the piston by pulling it straight out, not at an angle.

NOTICE:

If the piston is pulled out at an angle, there is a possibility that the cylinder bore could be damaged.