Home › Brake › BRAKE SYSTEM (OTHER) › HYDRAULIC BRAKE BOOSTER(for RHD)
RM2660E _54 Brake _052820 BRAKE SYSTEM (OTHER) _0255427 HYDRAULIC BRAKE BOOSTER(for RHD) A

BRAKE SYSTEM (OTHER)  HYDRAULIC BRAKE BOOSTER(for RHD)  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL BRAKE BOOSTER PISTON SUB-ASSEMBLY

a.
F051194

Apply lithium soap base glycol grease to a new piston.


b.

Install the piston.

NOTICE:

When installing, be careful not to damage the seals, etc.



c.

Install the plug.


d.

Using 2 screwdrivers, install a new C-ring while pressing on the piston.

HINT:

Tape the screwdriver tip before use.



Hide 47265 2.INSTALL MASTER CYLINDER BOOT

Hide 47264 3.INSTALL MASTER CYLINDER PUSH ROD CLEVIS

a.
U116679

Install the brake master cylinder side lock nut and rod operating adapter to the brake master cylinder.

Torque:
26 N*m (260 kgf*cm, 19 ft.*lbf)


b.
C177091

Install the lock nut and master cylinder push rod clevis to the rod operating adapter.

Torque:
26 N*m (260 kgf*cm, 19 ft.*lbf)


Hide 47217 4.INSTALL MASTER CYLINDER SOLENOID

a.
F051196

Install a new gasket.

NOTICE:

Keep all surfaces of the master cylinder solenoid, master cylinder and gasket, especially contact surfaces, away from water and dust.



b.
U116680

Install the master cylinder solenoid with 6 new bolts.

Torque:
32 N*m (325 kgf*cm, 24 ft.*lbf)


Hide 47955A 5.INSTALL BRAKE BOOSTER ACCUMULATOR PIPE

a.
C172891

Install the brake booster accumulator pipe and compression spring.

NOTICE:

Ensure that no foreign matter enters the pump.



b.

Install a new O-ring to the brake booster accumulator.


c.

Install the brake booster accumulator.

Torque:
57 N*m (585 kgf*cm, 42 ft.*lbf)


Hide 47967A 6.INSTALL NO. 1 BRAKE BOOSTER PUMP BRACKET

a.
U116678

Install the brake booster pump bush to the No. 1 brake booster pump bracket.


b.

Using a 5 mm hexagon wrench, install the No. 1 brake booster pump bracket with the 2 bolts.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)


Hide 47070B 7.INSTALL BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY

a.
U116681

Using a 4 mm hexagon wrench, install the 2 pins to the brake master cylinder.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)


b.

Install 2 new brake booster pump collars and 2 brake booster pump bushes to the brake booster with accumulator pump assembly.


c.
U157357

Install the brake booster with accumulator pump assembly to the brake master cylinder.


d.
U149527

Install a new clip.


e.
U156862E04
1.521,1.5 1.365,1.625 false 1.677,1.469 2.073,1.26 false 2.094,1.167 2.802,1.323 0.708,0.156 10 false Red Cable 0.479,1.594 1.271,1.75 0.792,0.156 10 false Black Cable

Connect the wire harnesses with the 2 screws.

Torque:
2.9 N*m (30 kgf*cm, 26 in.*lbf)


f.
U116675

Install 2 new plugs.


Hide 44551C 8.INSTALL NO. 1 BRAKE ACTUATOR TUBE

a.
C172200E03
1.292,1.844 1.271,1.51 false 1.292,1 1.75,0.604 1.75,0.604 1.823,0.604 false 1.667,1.833 2.698,2.042 1.031,0.208 10 false Fulcrum Length 1.865,0.531 3.031,0.688 1.167,0.156 10 false Union Nut Wrench

Using a union nut wrench, install the No. 1 brake actuator tube.

Torque:
without union nut wrench : 15 N*m (155 kgf*cm, 11 ft.*lbf)
with union nut wrench : 14 N*m (145 kgf*cm, 10 ft.*lbf)

HINT:
·

Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).

·

The torque value for use with a union nut wrench is effective when the union nut wrench is parallel to the torque wrench.




Hide 44571A 9.INSTALL NO. 1 BRAKE ACTUATOR HOSE

a.
C172887

Using needle nose pliers, install the brake actuator hose with the 2 clips.


Hide 47255 10.INSTALL MASTER CYLINDER RESERVOIR GROMMET

a.
F051416

Apply lithium soap base glycol grease to 3 new reservoir grommets.


b.

Install the 3 reservoir grommets to the brake master cylinder.

NOTICE:

Be careful of the size of each grommet.



Hide 47202 11.INSTALL BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

a.
C172198

Install the brake master cylinder reservoir sub-assembly with the screw.

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)


b.

Install the master cylinder reservoir filler cap.


c.
C172197E05
1.708,1.219 1.354,1.729 1.354,1.729 1.167,1.729 false 0.49,1.656 1.156,1.813 0.667,0.156 10 false Pin Punch

Using a pin punch and hammer, install a new pin to the brake master cylinder reservoir.


Hide 44591A 12.INSTALL NO. 1 BRAKE ACTUATOR BRACKET

a.
C172196

Install the brake fluid level warning switch connector to the No. 1 brake actuator bracket.


b.

Using a 5 mm hexagon wrench, install the No. 1 brake actuator bracket with the bolt.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)