Home › Brake › BRAKE (REAR) › REAR BRAKE › 2014.08–2015.08
RM2660E _54 Brake _052822 BRAKE (REAR) _0255431 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the LH side and RH side.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 42431 1.INSTALL REAR DISC

a.
C172168E08
1.875,0.969 1.875,0.25 1.875,0.25 2.458,0.25 false 1.906,1.031 2.198,1.031 2.198,1.031 2.198,0.25 false 2.5,0.177 3.219,0.385 0.719,0.208 10 true Matchmark

Align the matchmarks, and then install the rear disc.

HINT:

When replacing the rear disc with a new one, select the installation position where the rear disc has the minimum runout.



Hide 42491 2.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 47722A 3.INSTALL REAR DISC BRAKE CYLINDER MOUNTING LH

a.

Install a new boot and a new cylinder slide bush to the rear disc brake cylinder mounting.

NOTICE:

Install the boot securely to the grooves of the rear disc brake cylinder mounting.



b.
C170869

Install the rear disc brake cylinder mounting with 2 new bolts.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 47816 4.INSTALL REAR NO. 1 DISC BRAKE PAD SUPPORT PLATE

NOTICE:
·

The pad support plates can be reused if they are securely attached to the cylinder mounting. Therefore, do not remove the pad support plates from the cylinder mounting.

·

If a pad support plate is removed, replace it with a new one that is supplied with double-sided tape already attached.

·

Make sure to clean the cylinder mounting contact surface before attaching the pad support plates.



a.

Clean the cylinder mounting surface where the pad support plates will be attached.


b.

Remove the peeling paper from the double-sided tape, and install 2 new pad support plates to the cylinder mounting.


Hide 47817 5.INSTALL REAR NO. 2 DISK BRAKE PAD SUPPORT PLATE

NOTICE:
·

The pad support plates can be reused if they are securely attached to the cylinder mounting. Therefore, do not remove the pad support plates from the cylinder mounting.

·

If a pad support plate is removed, replace it with a new one that is supplied with double-sided tape already attached.

·

Make sure to clean the cylinder mounting contact surface before attaching the pad support plates.



a.

Clean the cylinder mounting surface where the pad support plates will be attached.


b.

Remove the peeling paper from the double-sided tape, and install 2 new pad support plates to the cylinder mounting.


Hide 47771A 6.INSTALL REAR DISC BRAKE PAD WEAR INDICATOR PLATE

a.

Install the pad wear indicator plate to the inner side disc brake pad.


Hide 04946 7.INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

a.

Install the anti-squeal shims to each brake pad.

NOTICE:

There should be no oil or grease on the friction surfaces of the brake pads and the rear disc.



Hide 8.INSTALL REAR DISC BRAKE PAD

NOTICE:
·

When installing the pads, make sure that the No. 1 and No. 2 disc brake pad support plates are securely attached to the cylinder mounting. The pad support plates are attached to the cylinder mounting with double-sided tape.

·

If a pad support plate is not securely attached to the cylinder mounting, replace it with a new one.



a.

Install the 2 disc brake pads to the disc brake cylinder mounting.


Hide 9.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY LH

a.

Apply lithium soap base glycol grease to the sliding part of the 2 cylinder slide pins.


b.
C170868

Install the cylinder with the 2 cylinder slide pins.

Torque:
88 N*m (897 kgf*cm, 65 ft.*lbf)


Hide 47319F 10.CONNECT REAR FLEXIBLE HOSE LH

a.
C165352

Install a new gasket and connect the flexible hose with the new union bolt.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 12.ADJUST PARKING BRAKE LEVER TRAVEL

Hide 42491 13.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 42603 14.INSTALL REAR WHEEL

Torque:
for Aluminum Wheel : 131 N*m (1336 kgf*cm, 97 ft.*lbf)
for Steel Wheel : 209 N*m (2131 kgf*cm, 154 ft.*lbf)