Home › Steering › POWER ASSIST SYSTEMS › VANE PUMP(for 1VD-FTV with DPF) › 2014.08–2015.08
RM2660E _55 Steering _052824 POWER ASSIST SYSTEMS _0255441 VANE PUMP(for 1VD-FTV with DPF) A

POWER ASSIST SYSTEMS  VANE PUMP(for 1VD-FTV with DPF)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

When installing parts, coat the parts indicated by arrows with power steering fluid (See page Steering>POWER ASSIST SYSTEMS>VANE PUMP (for 1VD-FTV without DPF)>COMPONENTS).


PROCEDURE

Hide 1.INSTALL VANE PUMP HOUSING OIL SEAL

a.

Coat the lip of a new oil seal with power steering fluid.


b.
C161397E01
2.14,0.318 2.583,0.507 0.443,0.189 10 SST 1.847,0.466 2.11,0.401 2.11,0.401 1.911,1.149 false

Using SST and a press, press in the oil seal.

SST
09950-60010  (09951-00320)
09950-70010  (09951-07150)

NOTICE:
·

Do not mistake the direction of the oil seal.

·

Do not damage the oil seal.




Hide 2.INSTALL VANE PUMP SHAFT BEARING

a.
C162116

Using a brass bar and hammer, tap on a new snap ring.

NOTICE:

Be careful not to damage the shaft.



b.
C162117

Using a press, press in the shaft into a new bearing.

NOTICE:

Be careful not to damage the bearing.



Hide 3.INSTALL VANE PUMP SHAFT WITH VANE PUMP SHAFT BEARING

a.

Temporarily install the rear housing to the front housing.


b.
C161398E03
0.917,0.232 1.129,0.415 0.212,0.183 10 *1 2.279,0.232 2.675,0.415 0.397,0.183 10 SST 1.141,0.314 1.685,0.27 false 2.225,0.314 1.894,0.528 false

Using SST and a press, press in the shaft with bearing into the front housing.

SST
09632-36010  

Text in Illustration
*1 Press


c.

Using a screwdriver, install a new snap ring into the front housing.


Hide 44316 4.INSTALL VANE PUMP GEAR

a.
C162119E01
0.135,0.34 0.534,0.544 0.399,0.204 10 SST 1.066,0.512 0.525,0.409 0.525,0.409 1.002,0.886 false

Using SST and a press, press in the gear to the shaft.

SST
09950-60010  (09951-00420)
09950-70010  (09951-07150)


b.

Remove the rear housing from the front housing.


Hide 5.INSTALL VANE PUMP FRONT SIDE PLATE

a.
C162123

Coat a new O-ring with power steering fluid and install it into the front housing.


b.

Coat the front side plate with power steering fluid.


c.
C162156

Coat a new O-ring with power steering fluid and install it onto the front side plate.


d.
C161399E03
2.713,0.267 3.116,0.444 0.403,0.177 10 *a 2.104,0.425 2.663,0.35 false

Align the notch of the front side plate with the notch of the front housing, and install the front side plate.

Text in Illustration
*a Align

NOTICE:

Make sure that the front side plate is installed facing in the correct direction.



Hide 6.INSTALL VANE PUMP CAM RING

a.

Coat the vane pump cam ring with power steering fluid


b.
C161400E03
2.774,0.195 3.184,0.371 0.410,0.176 10 *a 2.234,0.345 2.722,0.289 false

Align the notch of the cam ring with the notch of the front side plate, and install the cam ring with the inscribed mark facing upward.

Text in Illustration
*a Align

NOTICE:

Make sure that the cam ring is installed facing in the correct direction.



Hide 7.INSTALL VANE PUMP ROTOR AND VANE PUMP PLATE

a.

Install the rotor with the inscribed mark facing upward.


b.

Coat the 10 vane pump plates with power steering fluid.


c.
C161401E05
2.719,0.573 2.885,1.49 false 2.865,1.563 3.073,1.875 0.208,0.313 10 false *a

Install the 10 vane pump plates with the round end facing upward.

Text in Illustration
*a Round End

NOTICE:

Make sure that the 10 vane pump plates are installed facing in the correct direction.



Hide 8.INSTALL REAR VANE PUMP HOUSING

a.

Coat a new O-ring with power steering fluid and install it onto the rear housing.


b.

Coat the straight pin of the rear vane pump housing with power steering fluid.


c.
C162122E02
0.394,1.028 0.612,1.223 0.219,0.195 10 *a 0.616,1.129 0.953,1.129 0.953,1.129 1.237,1.206 false

Align the straight pin of the rear vane pump housing with the notches of the cam ring, front side plate and front housing.

Text in Illustration
*a Align

NOTICE:

Make sure that the O-ring is not protruding anywhere when installing the vane pump rear housing.



d.
C162098

Install the rear housing with the 4 bolts.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


Hide 44337 9.INSTALL POWER STEERING SUCTION PORT UNION

a.

Coat a new O-ring with power steering fluid and install it to the suction port union.


b.

Install the suction port union to the vane pump with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 10.INSPECT TOTAL PRELOAD

a.

Check that the pump rotates smoothly without abnormal noise.


b.

Temporarily install a service bolt.

Recommended service bolt:
Thread diameter:

10 mm (0.394 in.)

Thread pitch:

1.25 mm (0.0492 in.)

Bolt length:

50 mm (1.97 in.)



c.
C178182E02
2.324,1.491 3.112,1.652 0.788,0.161 10 *1 2.298,1.572 2.118,1.572 false 2.118,1.572 1.49,0.969 false

Using a torque wrench, measure the pump rotating torque.

Standard rotating torque:

0.27 N*m (2.8 kgf*cm, 2.4 in.*lbf) or less


Text in Illustration
*1 Service Bolt

If the rotating torque is not as specified, check the oil seal.