Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › from 2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255452 STEERING LOCK SYSTEM U

STEERING COLUMN  STEERING LOCK SYSTEM  TERMINALS OF ECU  


TERMINAL INSPECTION


U156198E01
1.74,0.781 2.083,0.938 0.344,0.156 11 false E26

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
E26-1 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
E26-3 (IGE) - E26-1 (GND) Input W - W-B Steering lock motor activation command signal (motor activation command signal sent from certification ECU (smart key ECU assembly)) Any door opened when conditions below met, and then steering lock motor activated:
·

Shift lever in P

·

Steering lock unlocked in advance by carrying key and turning engine switch on (IG)

·

After above conditions met, engine switch turned off


Pulse generation (see waveform)
Entry&Start
·

Power Supply Short

·

Unlock Request Receive

·

Lock Request Receive


E26-4 (SLP1) - E26-1 (GND) Output R - W-B Steering lock bar position signal (output signal from steering unlock sensor) Steering locked → unlocked 11 to 14 V → Below 1.2 V
Entry&Start
·

Push Start Error

·

Sensor Value


E26-5 (LIN) - E26-1 (GND) Input/Output V - W-B LIN communication line - -
Entry&Start
·

Steering Lock Start Cond


E26-6 (IG2) - E26-1 (GND) Input P - W-B Power source mode signal (IG2 power supply input for entire steering lock actuator assembly) Engine switch off → engine switch on (IG) Below 1 V → 11 to 14 V
Entry&Start
·

Ignition Switch


E26-7 (B) - Body ground Input G - Body ground Power source Always 11 to 14 V -

NOTICE:

There are 1 motor and 2 sensors built into the steering lock actuator assembly.


HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

-

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P.

-

To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.




i.
U113990E32
1.771,1.708 1.854,1.99 1.854,1.99 1.906,1.99 false 1.563,0.448 2.677,0.208 2.677,0.208 2.75,0.208 false 2.667,0.219 2.469,0.469 false 2.927,1.583 3.292,1.781 0.365,0.198 10 false GND 1.948,1.917 2.302,2.063 0.354,0.146 10 false *b 2.813,0.115 3.177,0.344 0.365,0.229 10 false *a

Waveform

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Item Content
Tester Connection E26-3 (IGE) - E26-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Vehicle Condition Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating

Text in Illustration
*a Steering lock motor not operating
*b Steering lock motor operating