Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › 2014.08–2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255452 STEERING LOCK SYSTEM J

STEERING COLUMN  STEERING LOCK SYSTEM  Power Source Circuit  


DESCRIPTION

This circuit supplies power source voltage from the battery to terminal B of the steering lock ECU.

The diagnosis information of the steering lock ECU is transmitted to the intelligent tester via the certification ECU (smart key ECU assembly) as the steering lock ECU is not connected to the CAN communication system.

WIRING DIAGRAM

C165589E02
0.569,1.304 1.380,1.489 0.811,0.185 10 from Battery 2.499,1.457 3.309,1.642 0.810,0.185 10 STR LOCK 3.488,2.931 3.820,3.116 0.332,0.185 10 E26 4.205,1.304 4.603,1.489 0.398,0.185 10 B 3.986,1.423 4.135,1.608 0.148,0.185 10 7 4.205,2.292 4.603,2.477 0.398,0.185 10 GND 5.125,1.786 6.530,1.971 1.405,0.185 10 Steering Lock Motor 3.986,2.411 4.135,2.596 0.148,0.185 10 1 3.488,3.098 5.715,3.440 2.227,0.342 10 Steering Lock Actuator Assembly (Steering Lock ECU) 4.205,1.8 4.689,1.985 0.484,0.185 10 SGND 3.986,1.919 4.135,2.104 0.148,0.185 10 2

CAUTION / NOTICE / HINT

HINT:

When the engine switch is off, the main body ECU may occasionally go into a non-active state called sleep mode. Therefore, before proceeding with the inspection, it is necessary to perform the following steps to wake up the ECU:

With the engine switch off, open the driver door. Then (with the engine switch still off) open and close any door several times at 1.5 second intervals.


PROCEDURE

1.INSPECT FUSE (STR LOCK)
a.

Remove the STR LOCK fuse from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
STR LOCK fuse Always Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - BATTERY)

NG

REPLACE FUSE

2.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - BATTERY)
U164612E02
2.688,2.99 2.583,2.99 2.583,2.99 2.292,2.156 true 0.365,0.24 2.708,0.604 2.344,0.365 10 false Front view of wire harness connector: (to Steering Lock ECU) 2.76,2.917 2.927,3.115 0.167,0.198 10 false B 0.302,2.01 0.677,2.24 0.375,0.229 10 false E26

a.

Disconnect the E26 steering lock ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E26-7 (B) - Body ground Always 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - BODY GROUND)
U164613E02
1.75,2.99 1.646,2.99 1.646,2.99 1.354,2.156 true 0.719,2.99 0.833,2.99 0.833,2.99 1.125,2.156 true 0.365,0.292 2.708,0.656 2.344,0.365 10 false Front view of wire harness connector: (to Steering Lock ECU) 1.813,2.896 2.281,3.094 0.469,0.198 10 false SGND 0.302,2.01 0.677,2.24 0.375,0.229 10 false E26 0.344,2.917 0.698,3.115 0.354,0.198 10 false GND

a.

Disconnect the E26 steering lock ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E26-1 (GND) - Body ground Always Below 1 Ω
E26-2 (SGND) - Body ground Always Below 1 Ω




OK

GO TO STEERING LOCK SYSTEM (PROBLEM SYMPTOMS TABLE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR