Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM › 2014.08–2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255453 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B2620  ECU Power Source Circuit Malfunction  


DESCRIPTION

The ECU power source circuit supplies positive voltage to the multiplex tilt and telescopic ECU.

DTC Code Detection Condition Trouble Area
B2620 The ECU power source voltage drops to 8 V or less and this condition continues for 10 sec. or more.
·

ECU-B1 fuse

·

Harness or connector

·

Multiplex tilt and telescopic ECU



WIRING DIAGRAM

C149263E48
3.906,0.792 4.542,0.99 0.635,0.198 10 false ECU-B1 0.792,0.625 1.646,0.823 0.854,0.198 10 false from Battery 5.823,0.656 6.698,0.99 0.875,0.333 10 false ECUB 5.823,2.344 6.302,2.625 0.479,0.281 10 false GND 5.573,0.531 5.927,0.885 0.354,0.354 10 false 9 5.521,2.219 5.792,2.563 0.271,0.344 10 false 11 5.667,2.885 5.99,3.073 0.323,0.188 10 false E27 5.667,3.083 6.75,3.521 1.083,0.438 10 false Multiplex Tilt and Telescopic ECU

PROCEDURE

1.INSPECT FUSE (ECU-B1)
a.

Remove the ECU-B1 fuse from the main body ECU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ECU-B1 fuse Always Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)

NG

REPLACE FUSE

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)
a.
U164518E02
2.385,2.708 2.646,2.99 true 0.177,0.188 2.542,0.635 2.365,0.448 10 false Rear view of wire harness connector: (to Multiplex Tilt and Telescopic ECU) 2.698,2.99 3.333,3.24 0.635,0.25 10 false 9 (ECUB) 1.958,1.354 2.25,1.552 0.292,0.198 10 false E27

Disconnect the E27 multiplex tilt and telescopic ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E27-9 (ECUB) - Body ground Always 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
a.
U164516E02
1.854,2.615 1.281,3.021 true 0.125,0.167 2.49,0.615 2.365,0.448 10 false Rear view of wire harness connector: (to Multiplex Tilt and Telescopic ECU) 0.854,3.052 1.5,3.25 0.646,0.198 10 false 11 (GND) 1.969,1.313 2.26,1.51 0.292,0.198 10 false E27

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E27-11 (GND) - Body ground Always Below 1 Ω




OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR