Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM › from 2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255453 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B2620  ECU Power Source Circuit Malfunction  


DESCRIPTION

The ECU power source circuit supplies positive (+) voltage to the multiplex tilt and telescopic ECU.

DTC No. Detection Item Trouble Area
B2620 The voltage of the ECU power source drops to 8 V or less and this condition continues for 10 secs. or more.
·

MPX-B NO. 1 fuse

·

Harness or connector

·

Multiplex tilt and telescopic ECU



WIRING DIAGRAM

C265384E12
5.656,3.063 7.073,3.438 1.417,0.375 10 false Multiplex Tilt and Telescopic ECU 5.656,2.865 6.031,3.042 0.375,0.177 10 false E144 5.792,2.365 6.219,2.552 0.427,0.188 10 false GND2 5.792,0.656 6.219,0.844 0.427,0.188 10 false ECUB 5.573,2.25 5.74,2.438 0.167,0.188 10 false 8 5.573,0.521 5.74,0.708 0.167,0.188 10 false 9 3.792,0.844 4.688,1.073 0.896,0.229 10 false MPX-B NO. 1 0.781,0.625 1.667,0.927 0.885,0.302 10 false from Battery

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)
a.
U165139E02
0.938,1.604 0.979,1.24 false 0.177,0.125 0.375,0.302 0.198,0.177 10 false *a 1.573,0.365 1.948,0.542 0.375,0.177 10 false E144 0.729,1.615 1.385,1.792 0.656,0.177 10 false ECUB

Disconnect the multiplex tilt and telescopic ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E144-9 (ECUB) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)



OK

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
a.
U165140E02
0.74,1.604 0.76,1.229 false 0.177,0.115 0.406,0.313 0.229,0.198 10 false *a 1.573,0.354 1.969,0.531 0.396,0.177 10 false E144 0.521,1.625 0.958,1.802 0.438,0.177 10 false GND2

Disconnect the multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E144-8 (GND2) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR