Home › Steering › STEERING COLUMN › STEERING SYSTEM › 2014.08–2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255454 STEERING SYSTEM N

STEERING COLUMN  STEERING SYSTEM  ADJUSTMENT  


PROCEDURE

Hide 1. STEERING OFF CENTER ADJUSTMENT PROCEDURE

HINT:

This is the adjustment procedure for steering off center.


a.

Inspect steering wheel off center.

i.
C170782E02
1.448,0.302 2.052,0.302 2.052,0.302 2.25,0.594 false 2.333,1.156 1.292,0.813 1.292,0.813 2.26,1.302 false 1.51,1.24 1.927,1.375 false 0.396,0.229 1.365,0.406 0.969,0.177 10 false Steering Wheel 0.323,0.698 1.24,0.885 0.917,0.188 10 false Masking Tape 0.385,1.135 1.49,1.469 1.104,0.333 10 false Steering Column Upper Cover

Apply masking tape to the top center of the steering wheel and steering column upper cover.


ii.

Drive the vehicle in a straight line for 100 m (328 ft.) at a constant speed of 56 km/h (35 mph), and hold the steering wheel to maintain the course.


iii.
C170783E03
1.51,0.24 2.083,0.24 2.083,0.24 2.438,0.698 false 2.49,1.052 1.406,1.135 1.406,1.135 2.5,1.396 false 1.458,1.51 2.104,1.51 false 0.344,0.167 1.427,0.531 1.083,0.365 10 false Steering Column Upper Cover 0.51,1.063 1.344,1.219 0.833,0.156 10 false Marked Line 0.375,1.448 1.406,1.615 1.031,0.167 10 false Steering Wheel

Draw a line on the masking tape as shown in the illustration.


iv.

Turn the steering wheel to the center position.

HINT:

Look at the upper surface of the steering wheel, steering spoke and SRS airbag line to find the center position.



v.
C170784E03
2.49,1.365 1.313,1.115 1.313,1.115 2.5,1.063 false 1.448,1.615 2.104,1.615 false 1.615,0.271 1.771,0.271 1.771,0.271 2.208,0.708 false 0.458,0.198 1.604,0.573 1.146,0.375 10 false Steering Column Upper Cover 0.438,1.01 1.26,1.188 0.823,0.177 10 false Marked Line 0.333,1.531 1.417,1.708 1.083,0.177 10 false Steering Wheel

Draw a new line on the masking tape on the steering wheel as shown in the illustration.


vi.

Measure the distance between the 2 lines on the masking tape on the steering wheel.


vii.

Convert the measured distance to steering angle.

HINT:
·

Measured distance 1 mm (0.0394 in.) = Steering angle of approximately 1°.

·

Make a note of the steering angle.





b.

Adjust the steering angle.

i.
C170785E13
1.344,0.844 1.813,0.25 1.813,0.25 1.156,0.792 false 1.896,0.146 2.688,0.323 0.792,0.177 10 false Matchmark

Draw a line on the RH and LH tie rod ends and rack ends respectively where it can be easily seen.


ii.

Using a paper gauge, measure the distance from the RH and LH tie rod ends to the rack end screws.

HINT:
·

Measure both the RH and LH sides.

·

Make a note of the measured values.




iii.
C145857

Remove the RH and LH boot clips from the rack boots.


iv.

Loosen the RH and LH lock nuts.


v.

Turn the RH and LH rack ends by the same amount (but in different directions) according to the steering angle.

HINT:

One 360 °turn of the rack end (1.5 mm (0.0591 in.) horizontal movement) equals 12 °of steering angle.



vi.

Tighten the RH and LH lock nuts to the specified torque.

Torque:
82 N*m (836 kgf*cm, 60 ft.*lbf)

NOTICE:

Make sure that the difference in length between the RH and LH tie rod ends and rack end screws is within 1.5 mm (0.0591 in.).



vii.

Install the RH and LH boot clips.