Home › Steering › STEERING COLUMN › STEERING SYSTEM › from 2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255454 STEERING SYSTEM N

STEERING COLUMN  STEERING SYSTEM  ADJUSTMENT  


PROCEDURE

Hide 1. STEERING OFF CENTER ADJUSTMENT PROCEDURE

HINT:

This is the adjustment procedure for steering off center.


a.

Inspect steering wheel off center.

i.
C348614E03
1.125,0.292 1.406,0.448 true 1.76,0.708 2.354,0.406 2.354,0.406 1.948,0.99 true 2.167,1.198 2.438,1.115 true 0.896,0.198 1.24,0.438 0.344,0.24 10 false *1 2.49,1 2.833,1.24 0.344,0.24 10 false *2 2.396,0.26 2.74,0.5 0.344,0.24 10 false *a

Apply masking tape to the top center of the steering wheel and steering column upper cover.

Text in Illustration
*1 Steering Wheel
*2 Steering Column Upper Cover
*a Masking Tape


ii.

Drive the vehicle in a straight line for 100 m (328 ft.) at a constant speed of 56 km/h (35 mph), and hold the steering wheel to maintain the course.


iii.
C335434E01
1.736,0.508 2.292,0.381 2.292,0.381 1.736,0.937 false 2.326,0.267 2.545,0.453 0.218,0.186 10 *a

Draw a line on the masking tape as shown in the illustration.

Text in Illustration
*a Marked Line


iv.

Turn the steering wheel to the center position.

HINT:

Look at the upper surface of the steering wheel, steering spoke and SRS airbag line to find the center position.



v.
C335435E03
1.75,0.958 2.281,1.365 true 2.344,1.302 2.646,1.563 0.302,0.26 10 false *a

Draw a new line on the masking tape on the steering wheel as shown in the illustration.

Text in Illustration
*a Marked Line


vi.

Measure the distance between the 2 lines on the masking tape on the steering wheel.


vii.

Convert the measured distance to steering angle.

HINT:
·

Measured distance 1 mm (0.0394 in.) = Steering angle of approximately 1°.

·

Make a note of the steering angle.





b.

Adjust the steering angle.

i.
C170785E14
1.813,0.24 1.979,0.24 false 1.365,0.844 1.833,0.24 1.833,0.24 1.177,0.781 true 2.073,0.146 2.323,0.323 0.25,0.177 10 false *a

Draw a line on the RH and LH tie rod ends and rack ends respectively where it can be easily seen.

Text in Illustration
*a Matchmark


ii.

Using a paper gauge, measure the distance from the RH and LH tie rod ends to the rack end screws.

HINT:
·

Measure both the RH and LH sides.

·

Make a note of the measured values.




iii.
C179739

Remove the RH and LH boot clips from the rack boots.


iv.

Loosen the RH and LH lock nuts.


v.

Turn the RH and LH rack ends by the same amount (but in different directions) according to the steering angle.

HINT:

One 360 °turn of the rack end (1.5 mm (0.0591 in.) horizontal movement) equals 12 °of steering angle.



vi.

Tighten the RH and LH lock nuts to the specified torque.

Torque:
82 N*m (836 kgf*cm, 60 ft.*lbf)

NOTICE:

Make sure that the difference in length between the RH and LH tie rod ends and rack end screws is within 1.5 mm (0.0591 in.).



vii.

Install the RH and LH boot clips.



c.

w/ VGRS:

Perform variable gear ratio steering system calibration (See page Steering>VARIABLE GEAR RATIO STEERING>VARIABLE GEAR RATIO STEERING SYSTEM>CALIBRATION).