Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)
RM2660E _55 Steering _052826 STEERING COLUMN _0255458 STEERING COLUMN ASSEMBLY(for Manual Tilt and Manual Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Manual Tilt and Manual Telescopic Steering Column)  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

When using a vise, do not overtighten it.


PROCEDURE

Hide 45020A 1.REMOVE STEERING LOCK ACTUATOR ASSEMBLY (w/ Entry and Start System)

a.

Using a center punch, mark the center of the 2 tapered-head bolts.


b.

Using a 3 to 4 mm (0.118 to 0.157 in.) drill, drill a hole in the 2 bolts.


c.
C178340E01
2.577,0.049 3.219,0.392 0.642,0.343 10 Screw Extractor 2.538,0.146 2.288,0.146 false 2.288,0.146 2.288,0.964 false

Using a screw extractor, remove the 2 bolts and the steering lock actuator assembly from the steering column assembly.


Hide 85432 2.REMOVE KEY INTERLOCK SOLENOID (for Automatic Transmission)

a.
G034357

Remove the 2 screws and solenoid from the steering column upper bracket.


Hide 89783 3.REMOVE TRANSPONDER KEY AMPLIFIER (w/o Entry and Start System)

a.
C214793E02
0.667,1.448 0.896,1.677 0.896,1.677 1.031,1.677 false 1.031,1.531 2.24,1.844 1.208,0.313 10 true Protective Tape

Detach the 2 claws, slide the transponder key amplifier in the direction indicated by the arrow in the illustration and remove it from the steering column upper with switch bracket assembly.


Hide 4.REMOVE STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY (w/o Entry and Start System)

a.

Using a drill, drill a hole to insert a screw extractor into each steering lock bolt.


b.
U164467

Using a screw extractor, remove the 2 steering lock bolts, steering column upper with switch bracket and steering column upper clamp.


Hide 5.REMOVE IGNITION SWITCH LOCK CYLINDER ASSEMBLY (w/o Entry and Start System)

a.

Turn the ignition switch lock cylinder assembly to ACC.


b.
C214493E02
0.594,2.771 0.875,2.594 0.875,2.594 0.969,2.594 true 2.094,1.021 2.406,0.365 2.406,0.365 2.5,0.365 true 2.26,1.094 2.438,1.417 2.438,1.417 2.531,1.417 true 1.427,0.813 1.802,0.969 0.375,0.156 10 false Push 1.042,2.51 1.469,2.667 0.427,0.156 10 false ACC 1.5,2.406 1.927,2.563 0.427,0.156 10 false Pull 2.552,0.281 3.073,0.646 0.521,0.365 10 true Claw 2.563,1.344 3.219,1.688 0.656,0.344 10 true Stopper

Insert a thin-bladed screwdriver into the hole of the steering column upper bracket assembly as shown in the illustration and pull out the key until the claw of the ignition switch lock cylinder assembly contacts the stopper of the steering column upper bracket assembly.

NOTICE:

Be sure to pull out the key until the claw firmly contacts the stopper. There will be problems later if the key is not pulled out until the claw of the ignition switch lock cylinder assembly contacts the stopper of the steering column upper bracket assembly.



c.
C105483

Insert a thin-bladed screwdriver into the hole of the steering column upper bracket assembly as shown in the illustration, push the thin-bladed screwdriver in the direction shown in the illustration to detach the claw and pull out the ignition switch lock cylinder assembly.


Hide 84052 6.REMOVE UNLOCK WARNING SWITCH ASSEMBLY (w/o Entry and Start System)

a.
U164984E01
2.163,1.565 3.023,1.781 0.860,0.216 10 Center Part

Push up the center part of the unlock warning switch assembly, detach the 2 claws and remove the unlock warning switch assembly.

HINT:

Slide the unlock warning switch assembly in the direction indicated by the arrow in the illustration to remove it.



Hide 84450 7.REMOVE IGNITION OR STARTER SWITCH ASSEMBLY (w/o Entry and Start System)

a.
C358220

Detach the 2 claws and remove the ignition or starter switch assembly from the steering column upper bracket assembly.


Hide 45832 8.REMOVE TILT STEERING SUPPORT BOND CABLE (w/o Entry and Start System)

a.
C246796

Remove the 2 screws and tilt steering support bond cable.


Hide 45804J 9.REMOVE BREAK AWAY COLLAR SUB-ASSEMBLY (w/o Entry and Start System)

a.
C104462

Remove the 2 break away collars and 2 break away capsules from the break away bracket.


Hide 45262A 10.REMOVE TILT LEVER RETURN SPRING (w/o Entry and Start System)

a.
C248939E02
2.042,0.927 2.219,1.677 2.219,1.677 2.302,1.677 false 2.354,1.594 2.76,1.76 0.406,0.167 10 false SST

Using SST, remove the tilt lever return spring from the break away bracket and steering tilt lever.

SST
09921-00010  

HINT:

To avoid spatter, cover the area with a cloth.


NOTICE:

Do not let the damper fall off of the tilt lever return spring.



Hide 45261 11.REMOVE TILT STEERING JUMP UP SPRING (w/o Entry and Start System)

a.
C248940

Using pliers, pull the tilt steering jump up spring in the direction indicated by the arrow in the illustration and remove it from the break away bracket.

HINT:

To avoid spatter, cover the area with a cloth.



Hide 45833 12.LOOSEN NO. 1 TILT STEERING ADJUSTING NUT (w/o Entry and Start System)

a.
C248956

Lock the steering tilt lever.


b.
C104852

Using a hammer and chisel, loosen the staked part of the No. 1 tilt steering adjusting nut.


c.
C248944

Loosen the No. 1 tilt steering adjusting nut.

NOTICE:

Be sure to only loosen the No. 1 tilt steering adjusting nut. Do not remove it.



Hide 45821B 13.REMOVE NO. 1 TILT STEERING SUPPORT REINFORCEMENT (w/o Entry and Start System)

a.
C248942

Remove the steering tilt lever bolt and No. 1 tilt steering support reinforcement from the steering tilt lever.

NOTICE:

The steering tilt lever bolt has a left-handed thread.



Hide 45880B 14.REMOVE NO. 1 TILT LEVER LOCK BOLT (w/o Entry and Start System)

a.
C248943

Using an 8 mm socket hexagon wrench, loosen the No. 1 tilt lever lock bolt until it can be turned by hand.

NOTICE:

The loosening direction for the No. 1 tilt lever lock bolt is the loosening direction for bolts with a left-handed thread.



b.
C248944

Remove the No. 1 tilt steering adjusting nut from the No. 1 tilt lever lock bolt.


c.
C248945

Remove the tilt steering rotor, thrust needle roller bearing and steering column tube stopper from the No. 1 tilt lever lock bolt.


d.
C248946

Remove the No. 1 tilt lever lock bolt, steering tilt lever and steering column tube stopper from the break away bracket.


Hide 45878 15.REMOVE BREAK AWAY BRACKET (w/o Entry and Start System)

a.
C248947

Remove the break away bracket from the steering column upper tube.


Hide 45824 16.REMOVE TILT STEERING PAWL ASSEMBLY (w/o Entry and Start System)

a.
C104463

Remove the tilt steering pawl assembly from the steering column upper tube.


Hide 45263 17.REMOVE NO. 1 STEERING COLUMN RING (w/o Entry and Start System)

a.
U164982E01
0.384,0.102 1.382,0.466 0.997,0.364 10 Snap Ring Expander 1.706,1.557 2.372,1.720 0.666,0.163 10 Snap Ring 2.711,1.416 2.602,1.659 2.602,1.659 2.543,1.659 false

Using a snap ring expander, remove the shaft snap ring from the steering main shaft assembly.

NOTICE:

Do not damage the steering main shaft assembly.



Hide 45277A 18.REMOVE TILT STEERING SUPPORT (w/o Entry and Start System)

a.
C247264

Remove the bolt and tilt steering support.


Hide 45204 19.REMOVE STEERING LOWER COLUMN TUBE ASSEMBLY (w/o Entry and Start System)

a.
C249446

Remove the steering column lower tube assembly from the steering column upper tube.


Hide 45765 20.REMOVE TELESCOPIC STEERING GUIDE (w/o Entry and Start System)

a.
U164468

Remove the telescopic steering guide from the steering lower column tube assembly.


Hide 45877A 21.REMOVE STEERING COLUMN BRACKET SPACER (w/o Entry and Start System)

a.
U164471E01
2.597,2.016 2.947,2.223 0.350,0.207 10 SST 1.457,0.332 1.807,0.538 0.350,0.207 10 SST 2.62,0.28 2.970,0.487 0.350,0.207 10 SST 1.274,0.773 1.342,0.412 1.342,0.412 1.417,0.412 false 3.141,0.773 3.055,0.354 3.055,0.354 2.981,0.354 false 1.739,3.358 2.319,2.096 false

Using SST and a hammer, tap out the steering column bracket spacer from the steering lower column tube assembly.

SST
09201-10000  (09201-01080)
09950-70010  (09951-07100)


Hide 45813 22.REMOVE NO. 1 TILT STEERING SUPPORT COLLAR (w/o Entry and Start System)

a.
C104468

Remove the 2 No. 1 tilt steering support collars from the steering lower column tube assembly.


Hide 45210 23.REMOVE STEERING MAIN SHAFT ASSEMBLY (w/o Entry and Start System)

a.
U164469E02
3.417,0 3.333,0.396 3.333,0.396 3.25,0.396 false 2.26,1.792 2.396,1.792 2.396,1.792 2.521,1.448 false 0.427,0.083 1.135,0.469 0.708,0.385 10 true Snap Ring Expander 1.573,1.698 2.292,1.969 0.719,0.271 10 true Snap Ring

Using a snap ring expander, remove the shaft snap ring from the steering main shaft assembly.

NOTICE:

Do not damage the steering main shaft assembly.



b.

Remove the steering main shaft assembly from the steering column upper tube.