Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)
RM2660E _55 Steering _052826 STEERING COLUMN _0255458 STEERING COLUMN ASSEMBLY(for Manual Tilt and Manual Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Manual Tilt and Manual Telescopic Steering Column)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

When using a vise, do not overtighten it.


PROCEDURE

Hide 45210 1.INSTALL STEERING MAIN SHAFT ASSEMBLY (w/o Entry and Start System)

a.

Install the steering main shaft assembly to the steering column upper tube.


b.
U164469E02
3.417,0 3.333,0.396 3.333,0.396 3.25,0.396 false 2.26,1.792 2.396,1.792 2.396,1.792 2.521,1.448 false 0.427,0.083 1.135,0.469 0.708,0.385 10 true Snap Ring Expander 1.573,1.698 2.292,1.969 0.719,0.271 10 true Snap Ring

Using a snap ring expander, install a new shaft snap ring to the steering main shaft assembly.

NOTICE:
·

Make sure the steering main shaft snap ring is securely installed to the groove.

·

Do not damage the steering main shaft assembly.




Hide 45813 2.INSTALL NO. 1 TILT STEERING SUPPORT COLLAR (w/o Entry and Start System)

a.
C104850E03
1.979,0.938 2.302,1.135 0.323,0.198 10 false 15° 1.979,1.51 2.302,1.708 0.323,0.198 10 false 15°

Install the 2 No. 1 tilt steering support collars to the steering lower column tube assembly.

NOTICE:

When installing the No. 1 tilt steering support collar, make sure that the cutout portion is aligned as shown in the illustration.



Hide 45877A 3.INSTALL STEERING COLUMN BRACKET SPACER (w/o Entry and Start System)

a.
C358223E01
1.917,2.208 2.198,2.385 0.281,0.177 10 false 15° 1.927,2.438 2.208,2.615 0.281,0.177 10 false 15°

Clamp the steering column bracket spacer and steering lower column tube assembly in a vise between a cloth and aluminum plates, and install the steering column bracket spacer to the steering lower column tube assembly using the vise.

NOTICE:

When installing the steering column bracket spacer, make sure that it is positioned so that the inner diameter is as shown in the illustration.



Hide 45765 4.INSTALL TELESCOPIC STEERING GUIDE (w/o Entry and Start System)

a.
C358226E01
1.042,0.323 1.188,0.208 1.188,0.208 1.438,0.208 true 1.521,0.135 2.292,0.333 0.771,0.198 10 false Match

Align the 3 protrusions of the telescopic steering guide with the 3 holes of the steering lower column tube assembly and install the telescopic steering guide.


Hide 45204 5.INSTALL STEERING LOWER COLUMN TUBE ASSEMBLY (w/o Entry and Start System)

a.
U164983

Apply MP grease to the area of the steering main shaft assembly indicated by the arrow in the illustration.


b.
C248949

Install the steering lower column tube assembly to the steering column upper tube.


Hide 45277A 6.INSTALL TILT STEERING SUPPORT (w/o Entry and Start System)

a.
C247264

Install the tilt steering support with the bolt.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


Hide 45263 7.INSTALL NO. 1 STEERING COLUMN RING (w/o Entry and Start System)

a.
U164982E01
0.384,0.102 1.382,0.466 0.997,0.364 10 Snap Ring Expander 1.706,1.557 2.372,1.720 0.666,0.163 10 Snap Ring 2.711,1.416 2.602,1.659 2.602,1.659 2.543,1.659 false

Using a snap ring expander, install a new No. 1 steering column ring to the steering main shaft.

NOTICE:
·

Make sure the No. 1 steering column ring is securely installed to the groove.

·

Do not damage the steering main shaft assembly.




Hide 45824 8.INSTALL TILT STEERING PAWL ASSEMBLY (w/o Entry and Start System)

a.
C104475

Install the tilt steering pawl assembly to the steering column upper tube.

NOTICE:

When installing the tilt steering pawl assembly, position the opening as shown in the illustration.



Hide 45878 9.INSTALL BREAK AWAY BRACKET (w/o Entry and Start System)

a.
C248948

Apply MP grease to the sliding areas of a new break away bracket and install it to the steering column upper tube.


Hide 45873 10.INSTALL STEERING COLUMN TUBE STOPPER (w/o Entry and Start System)

a.
C248950E02
2.24,0.802 1.677,0.115 true 1.583,0.125 1.896,0.125 1.896,0.125 2.302,0.469 true 0.938,0.052 1.51,0.365 0.573,0.313 10 true Parallel

Apply MP grease to the sliding surface of the steering column tube stopper (the one with the groove) and install it to the break away bracket.

NOTICE:

Align the flat edge of the steering column tube stopper and the raised sliding area of the break away bracket as shown in the illustration.



b.
U165191E02
2.688,0.958 2.521,1.229 2.521,1.229 2.521,1.542 false 2.698,1.458 3.208,1.625 0.51,0.167 10 false Parallel

Apply MP grease to the sliding surface of the steering column tube stopper (the one without the groove) and install it to the break away bracket.

NOTICE:

Align the flat edge of the steering column tube stopper and the raised sliding area of the break away bracket as shown in the illustration.



Hide 45880B 11.INSTALL NO. 1 TILT LEVER LOCK BOLT (w/o Entry and Start System)

a.
C358234

Apply MP grease to the sliding surface of the steering tilt lever and install it to the No. 1 tilt lever lock bolt.


b.
C248952

Install the No. 1 tilt lever lock bolt to the break away bracket.

NOTICE:
·

Do not drop the steering column tube stopper.

·

Pass the No. 1 tilt lever lock bolt through the hole of the tilt steering pawl assembly.




c.
C248953

Apply MP grease to the sliding surface of the thrust needle roller bearing and install it to the No. 1 tilt lever lock bolt.


d.

Temporarily install the tilt steering rotor to the No. 1 tilt lever lock bolt with a new No. 1 tilt steering adjusting nut.


e.
C248954

Using an 8 mm socket hexagon wrench, tighten the No. 1 tilt lever lock bolt.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)

NOTICE:

The tightening direction for the No. 1 tilt lever lock bolt is the tightening direction for bolts with a left-handed thread.



Hide 45277A 12.INSTALL NO. 1 TILT STEERING SUPPORT REINFORCEMENT (w/o Entry and Start System)

a.
C248955

Install the No. 1 tilt steering support reinforcement to the steering tilt lever with the steering tilt lever bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

The tightening direction for the steering tilt lever bolt is the tightening direction for bolts with a left-handed thread.



Hide 45833 13.TIGHTEN NO. 1 TILT STEERING ADJUSTING NUT (w/o Entry and Start System)

a.
C248956

Lock the steering tilt lever.


b.
C248957E01
0.18,0.064 0.605,0.257 0.425,0.193 10 Hold 2.878,1.45 3.303,1.643 0.425,0.193 10 Turn

Using an 8 mm socket hexagon wrench, hold the No. 1 tilt lever lock bolt in place and tighten the No. 1 tilt steering adjusting nut.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


c.
C216017

Using pliers, stake the No. 1 tilt steering adjusting nut as shown in the illustration.

NOTICE:

After staking the No. 1 tilt steering adjusting nut, make sure it is not loose.



Hide 45261 14.INSTALL TILT STEERING JUMP UP SPRING (w/o Entry and Start System)

a.
C104486

Using pliers, move the tilt steering jump up spring in the direction indicated by the arrow in the illustration to install it to the break away bracket.

NOTICE:

To avoid spatter, cover the area with a cloth.



Hide 45262A 15.INSTALL TILT LEVER RETURN SPRING (w/o Entry and Start System)

a.
C248939E02
2.042,0.927 2.219,1.677 2.219,1.677 2.302,1.677 false 2.354,1.594 2.76,1.76 0.406,0.167 10 false SST

Using SST, install the tilt lever return spring to the break away bracket and steering tilt lever.

SST
09921-00010  

NOTICE:
·

To avoid spatter, cover the area with a cloth.

·

Do not let the damper fall off of the tilt lever return spring.




Hide 45832 16.INSTALL TILT STEERING SUPPORT BOND CABLE (w/o Entry and Start System)

a.
C246796

Install the steering support bond cable to the steering column with the 2 screws.


Hide 45804J 17.INSTALL BREAK AWAY COLLAR SUB-ASSEMBLY (w/o Entry and Start System)

a.
C104462E03
0.667,1.885 0.521,1.885 0.521,1.885 0.385,1.542 false 2.167,1.896 2.479,1.896 false 0.729,1.802 2.135,2.177 1.406,0.375 10 true Break Away Collar

Install the 2 new break away collars and 2 new break away capsules to the break away bracket.

NOTICE:

Do not compress the disc spring portion of the break away collar.



Hide 84450 18.INSTALL IGNITION OR STARTER SWITCH ASSEMBLY (w/o Entry and Start System)

a.
C358220

Attach the 2 claws to install the ignition or starter switch assembly to the steering column upper bracket assembly.


Hide 84052 19.INSTALL UNLOCK WARNING SWITCH ASSEMBLY (w/o Entry and Start System)

a.
C358235

Attach the 2 claws to install the unlock warning switch assembly to the steering column upper bracket assembly.

HINT:

Move the unlock warning switch assembly in the direction indicated by the arrow in the illustration to install it.



Hide 20.INSTALL IGNITION SWITCH LOCK CYLINDER ASSEMBLY (w/o Entry and Start System)

a.

Turn the ignition switch lock cylinder assembly to ACC.


b.
C214540E01
2.243,0.126 2.622,0.282 0.378,0.156 10 ACC 2.573,1.054 3.048,1.21 0.476,0.156 10 LOCK

Insert the ignition switch lock cylinder assembly into the steering column upper bracket assembly to install it.


c.

Check that the ignition switch lock cylinder assembly is securely fixed in place.


Hide 21.INSPECT STEERING LOCK OPERATION (w/o Entry and Start System)

a.
C103934

Remove the key and check that the steering lock operates.


b.
C214539E01
2.064,0.565 2.488,0.732 0.424,0.167 10 ACC 2.597,1.296 3.021,1.462 0.424,0.167 10 LOCK

Insert the key, turn the ignition switch to ACC and check that the steering lock disengages.


Hide 22.INSTALL STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY (w/o Entry and Start System)

a.
C103936

Install the steering column upper with switch bracket assembly and steering column upper clamp with 2 new steering lock set bolts, and tighten the bolts until the heads break off.


Hide 89783 23.INSTALL TRANSPONDER KEY AMPLIFIER (w/o Entry and Start System)

a.
C358236

Attach the 2 claws to install the transponder key amplifier to the steering column upper with switch bracket assembly.


Hide 85432 24.INSTALL KEY INTERLOCK SOLENOID (for Automatic Transmission)

a.
G034357

Install the key interlock solenoid to the steering column upper bracket with the 2 screws.


Hide 45020A 25.INSTALL STEERING LOCK ACTUATOR ASSEMBLY (w/ Entry and Start System)

C178341

a.

Temporarily install the steering lock actuator assembly with 2 new tapered-head bolts.


b.

Tighten the 2 tapered-head bolts until the bolt heads break off.