Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/ Navigation System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255478 AUDIO AND VISUAL SYSTEM(w/ Navigation System) D

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/ Navigation System)  OPERATION CHECK  


CHECK HARD DISK DRIVE


HINT:
·

Check the hard disk drive (HDD) built into the multi-media module receiver assembly.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E226244

Select "Failure Diagnosis" from the "Service Menu" screen.


c.
E225796

Select "HDD Check" from the "Failure Diagnosis" screen.


d.
E225797E01
2.499,0.803 2.499,1.731 false 2.407,1.725 2.586,1.893 0.179,0.167 10 *a

HDD Check

i.

Select "HDD Check" to start the HDD check.


ii.

Check that the result is displayed when the HDD check is completed.

Screen Description
Display (Result) Description
Checking Check is in progress
OK Hard disk drive is normal
NG Hard disk drive is malfunctioning

Text in Illustration
*a Result

HINT:
·

After selecting "HDD Check", it may take a while until the result is displayed.

·

If the cabin temperature is -20°C (-4°F) or lower, or 65°C (149°F) or higher, the HDD may not operate normally, and "NG" may be shown on the display. Make sure to perform the inspection with the cabin at an appropriate temperature.

·

If "NG" is displayed even when the cabin temperature is appropriate, replace the HDD with a new one.






CHECK PANEL & STEERING SWITCH


HINT:
·

The multi-media module receiver assembly panel switches and steering switches are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E225778

Select "Panel&Steering Switch" from the "Function Check/Setting I" screen.


d.

Panel & Steering Switch Check Mode

i.
E225786E01
2.269,1.407 3.085,1.407 false 0.344,1.149 1.04,1.149 false 2.888,1.063 3.085,1.063 false 0.148,1.048 0.304,1.200 0.156,0.152 10 *a 3.087,0.962 3.243,1.114 0.156,0.152 10 *b 3.087,1.327 3.243,1.480 0.156,0.152 10 *c

Operate each switch and check that the switch conditions are correctly displayed.

Screen Description
Display Content
*a: Switch condition "Pushed" is displayed when any switch is pushed
*b: Number of switches pushed
·

Number of switches pushed at once is displayed

·

If more than 3 switches are pushed at once, "More than 3" is displayed


*c: Rotary switch direction Direction of rotary switch is displayed

NOTICE:

When the "SETUP" switch is pressed and held for 3 seconds or more, diagnostic mode will be canceled.





CHECK TOUCH SWITCH


HINT:
·

The touch switches on the screen are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E225779

Select "Touch Switch" from the "Function Check/Setting I" screen.


d.
E176521

Touch Switch Check

i.

Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

HINT:
·

A "+" mark is displayed where the display is touched.

·

The "+" mark remains on the display even after the finger is removed.






CHECK MIC & VOICE RECOGNITION


HINT:
·

The microphone and microphone input level are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E225780

Select "Mic&Voice Recognition" from the "Function Check/Setting I" screen.


d.
E187218E13
2.209,0.722 2.53,0.163 2.53,0.163 2.261,0.163 false 2.052,0.089 2.226,0.240 0.174,0.151 10 *a 1.655,1.881 1.829,2.032 0.174,0.151 10 *b 2.007,1.881 2.182,2.032 0.174,0.151 10 *c 2.354,1.881 2.528,2.032 0.174,0.151 10 *d 1.738,1.398 1.738,1.848 false 2.08,1.398 2.08,1.848 false 2.421,1.398 2.421,1.848 false 2.873,1.322 3.122,1.322 false 3.17,1.228 3.344,1.379 0.174,0.151 10 *e

Microphone & Voice Recognition Check

Screen Description
Display Content
*a: Microphone input level meter Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels.
*b: Recording switch Starts recording.
*c: Stop switch Stops recording and playing.
*d: Play switch Plays the recorded voice.
*e: Recording indicator Comes on while recording.

i.

When speaking into the microphone, check that the microphone input level meter changes according to the input level.

HINT:

The microphone is active at all times when this screen is displayed.



ii.

Push the recording switch and perform voice recording.

HINT:
·

Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.

·

While recording or playing, the switches other than the stop switch cannot be pushed.

·

When no recording is present, the play switch cannot be pushed.

·

Recording will stop after 5 seconds or when the stop switch is pushed.




iii.

Check that the recording indicator remains on while recording and that the recording can be played normally.




CHECK COLOR BAR


HINT:
·

The display color on the screen is checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E225781

Select "Color Bar" from the "Function Check/Setting I" screen.


d.

Color Bar Check Mode

i.
E226305

Select a color bar from the "Color Bar Check Mode" screen.


ii.

Check the display color.

HINT:
·

The entire screen turns to the color or stripe selected.

·

Touching the display will return to the "Color Bar Check Mode" screen.






CHECK GPS & VEHICLE SENSORS


HINT:
·

GPS information, vehicle signals and sensor signals are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E225782

Select "GPS&Vehicle Sensors" from the "Function Check/Setting I" screen.


d.
E246906

Select "Sensors Check" from the "GPS Information" screen.


e.
E226261E01
2.879,0.921 3.103,0.921 false 3.165,0.838 3.362,1.001 0.198,0.163 10 *a 2.879,1.23 3.103,1.23 false 3.165,1.147 3.362,1.310 0.198,0.163 10 *b

Vehicle Sensors

Screen Description
Display Content
*a: Vehicle signal Vehicle speed signal condition is displayed.
*b: Sensor signal Gyro sensor output condition is displayed.

HINT:

This screen is updated once per second.


i.

Check all the signals and sensors when vehicle signal information is displayed.




CHECK VEHICLE SIGNAL


HINT:
·

Vehicle signals received by the multi-media module receiver assembly are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E225783

Select "Vehicle Signal" from the "Function Check/Setting I" screen.


d.

Vehicle Signal Check Mode

i.
E225776

When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.

Screen Description
Display Content
Battery Battery voltage is displayed.
IG Engine switch ON/OFF state is displayed.
PKB Parking brake ON/OFF state is displayed.
REV Reverse signal ON/OFF state is displayed.
SPEED Vehicle speed is displayed in km/h.
TAIL Tail signal (Light control switch) ON/OFF state is displayed.
ADIM/TCAN Brightness state DIM (with) / BRIGHT (without) is displayed.

HINT:
·

Only items sending vehicle signals will be displayed.

·

This screen displays vehicle signals input to the multi-media module receiver assembly.

·

This screen is updated once per second when vehicle input signals change.






CHECK HANDS-FREE VOICE QUALITY AND VOLUME SETTING


HINT:
·

The hands-free volume of a "Bluetooth" compatible phone can be adjusted using the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E225784

Select "HF Voice Quality Setting" from the "Function Check/Setting I" screen.


d.
E239452E01
0.312,0.683 0.544,0.683 false 0.114,0.58 0.281,0.743 0.167,0.163 10 *a 0.312,0.992 0.544,0.992 false 0.114,0.889 0.281,1.052 0.167,0.163 10 *b

Hands-Free Voice Quality Setting (Receive/Send Voice Level adjustment)

Screen Description
Display Content
*a: Receive voice level adjustment Setting for the voice level received from "Bluetooth" compatible phones.
*b: Send voice level adjustment Setting for the voice level sent from "Bluetooth" compatible phones.

NOTICE:

Sound quality may deteriorate when the receive voice or send voice level is changed more than necessary. For this reason, check that the received voice or sent voice quality is still acceptable after changing this setting.


i.

If the voice level is low, press the up button, and if the voice level is loud, press the down button.

HINT:
·

Settings will be applied when the up or down button is selected.

·

The received voice level adjustment ranges from -5 to +1.

·

The sent voice level adjustment ranges from -5 to +4.

·

The initial level is "0".





e.
E239453E01
2.885,0.85 3.092,0.85 false 3.118,0.751 3.353,0.966 0.236,0.215 10 *a 2.851,1.478 3.109,1.478 false 3.118,1.379 3.353,1.594 0.236,0.215 10 *b 1.798,1.809 1.798,1.551 false 1.7,1.813 1.935,2.028 0.236,0.215 10 *c

Hands-Free Voice Quality Setting (Voice Quality Type adjustment)

Screen Description
*a Numeric keypad
*b Setting button
*c Reset button

i.

If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.


ii.

When adjusting the settings, use the number pad on the screen to input the voice quality type according to the table.

Settings
Parameter Target Phenomenon Voice Quality Type Positive Effect of Changing Voice Quality Negative Effect of Changing Voice Quality
A
(Noise)
The change in background noise the other party hears becomes unpleasant. 1000 The change in background noise the other party hears is reduced. Background noise when not talking becomes large.
B
(Noise)
The volume of the noise the other party hears temporarily becomes large. 2000 The temporary noise is reduced. The volume of voice may drop temporarily.
C
(Echo)
The other party hears weak echoes. 0100 The amount of echo is reduced (low level). Sound quality of the other party deteriorates (low level).
D
(Echo)
The other party hears strong echoes. 0200 The amount of echo is reduced (high level). Sound quality of the other party deteriorates (high level).
E
(Quality)
The other party hears harsh noises. 0010 Sound the other party hears becomes soft. Sound the other party hears becomes muffled.
F
(Quality)
You hear harsh noises. 0020 Sound you hear becomes soft. Sound you hear becomes muffled.

Settings (When multiple phenomenon occurred)
Parameter Target Phenomenon Voice Quality Type Positive Effect of Changing Voice Quality Negative Effect of Changing Voice Quality
A+C The change in background noise the other party hears becomes unpleasant and the other party hears weak echoes. 1100
·

The change in background noise the other party hears is reduced.

·

The amount of echo is reduced (low level).


·

Background noise when not talking becomes large.

·

Sound quality of the other party deteriorates (low level).


A+D The change in background noise the other party hears becomes unpleasant and the other party hears strong echoes. 1200
·

The change in background noise the other party hears is reduced.

·

The amount of echo is reduced (high level).


·

Background noise when not talking becomes large.

·

Sound quality of the other party deteriorates (high level).


B+C The volume of the noise the other party hears temporarily becomes large and the other party hears weak echoes. 2100
·

The temporary noise is reduced.

·

The amount of echo is reduced (low level).


·

The volume of voice may drop temporarily.

·

Sound quality of the other party deteriorates (low level).


B+D The volume of the noise the other party hears temporarily becomes large and the other party hears strong echoes. 2200
·

The temporary noise is reduced.

·

The amount of echo is reduced (high level).


·

The volume of voice may drop temporarily.

·

Sound quality of the other party deteriorates (high level).


C+E The other party hears weak echoes and harsh noises. 0110
·

The amount of echo is reduced (low level).

·

Sound the other party hears becomes soft.


·

Sound quality of the other party deteriorates (low level).

·

Sound the other party hears becomes muffled.


C+F The other party hears weak echoes and you hear harsh noises. 0120
·

The amount of echo is reduced (low level).

·

Sound you hear becomes soft.


·

Sound quality of the other party deteriorates (low level).

·

Sound you hear becomes muffled.



HINT:
·

The default value is "0000".

·

Settings will be applied when the setting button is selected.

·

If voice quality type values that are not in the table are input, the setting will not be applied and a positive effect may not be gained.

·

If the quality of phone calls decreases due to the changed settings, return the settings to "0000" by pressing the "INIT" switch.






CHECK DAB RECEPTION (w/ DAB Function)


HINT:
·

The reception condition of DAB (Digital Audio Broadcast) can be checked.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E235730

Select "Next Page" from the "Function Check/Setting I" screen.


d.
E235721

Select "DAB Reception Check" from the "Function Check/Setting II" screen.


e.
E245217E02
1.735,0.854 1.907,0.854 false 0.135,0.785 0.328,0.957 0.193,0.172 10 *a 0.338,0.875 0.532,0.875 false 2.723,1.172 3.049,1.172 false 2.722,1.326 3.048,1.326 false 1.94,0.776 2.133,0.948 0.193,0.172 10 *b 3.096,1.073 3.288,1.245 0.193,0.172 10 *c 3.099,1.249 3.292,1.421 0.193,0.172 10 *d

Select "DAB Reception Check" from the "Function Check/Setting II" screen.

*a: Channel Change Switch Description
Display Content
Up or down button Enables the channel to be changed to the one to be checked.

*b: Check Switch Description
Display Condition Content
Check Before/after check Starts checking
STOP During check Stops checking

*c: Antenna Connection Check Result Description
Display Content
OK Connected properly
NG Not connected properly
- Not equipped with DAB antenna.

*d: DAB Tuner Reception Level Check Result Description
Display Content
Black Good reception
Red Poor reception
- Not equipped with DAB antenna.

i.

Select the "Check" button to start the DAB reception check.


ii.

Check that the result is displayed when the DAB reception check is performed.




CHECK UNIT VERSION INFORMATION


HINT:

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.



b.
E229432

Select "Service Information" from the "Service Menu" screen.


c.
E228230

Select "Version Information" from the "Service Information" screen.


d.
E248722

Press the "Push" switch.


e.
E228232E01
1.893,0.414 2.035,0.166 2.035,0.166 2.265,0.166 false 0.642,0.797 0.355,0.797 false 2.123,1.314 3.144,1.314 false 2.302,0.058 2.471,0.228 0.169,0.169 10 *a 0.135,0.702 0.305,0.871 0.169,0.169 10 *b 0.642,1.314 0.355,1.314 false 0.135,1.22 0.305,1.389 0.169,0.169 10 *c 3.173,1.227 3.342,1.396 0.169,0.169 10 *d

Unit Version Information

Screen Description
Display Content
*a: Device name Target device
*b: Manufacturer name Manufacturer of the ECU (target device)
*c: Component name Component name of the ECU (target device)
*d: Version Version of the ECU (target device)

HINT:

Depending on the manufacturer, some component names and versions will be displayed differently.




CHECK SOFTWARE ERROR HISTORY


HINT:

This function is used to check the cause when the multi-media module receiver assembly screen is blacked out.


a.

Check software error history.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the intelligent tester on.


iv.

Enter the following menus: Body Electrical / Navigation System / Utility / Software Error History.


v.

When an item is stored for Software Error History, record it before repairing the multi-media module receiver assembly.

Software Error History Screen Description
Error Description Trigger Detail
Software Reset Navi Microcomputer Hexadecimal Number
Audio Microcomputer
CAN Microcomputer
No Video Signal Front Monitor
Rear Monitor
MOST Cold Restart Always

HINT:
·

Software Error History can store up to 5 history data items. If a new software error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.

·

If an error that is unsupported by the intelligent tester occurs, a "-" is displayed for the display items.





b.

Clear software error history.

i.

When DTCs are cleared using any of the following operations, Software Error History will be cleared as well (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(w/ Navigation System)>DTC CHECK / CLEAR).

·

Cleared using the intelligent tester.

·

Cleared using the system check mode screen.

·

Cleared using the unit check mode screen.





CHECK OPTICAL DISC ERROR HISTORY


HINT:

This function is used to check the cause when an optical disc error occurs.


a.

Check optical disc error history.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the intelligent tester on.


iv.

Enter the following menus: Body Electrical / Navigation System / Utility / Optical Disc Error History.


v.

When an item is stored for Optical Disc Error History, record it before proceeding with troubleshooting.

Optical Disc Error History Screen Description
Display Content
Error Type Displays the type of error.
Device Displays the malfunctioning device.
Date Displays the date and time that the malfunction occurred.

"Error Type" Screen Description
Error Type Detection Condition Action
Read Error When a disc read error occurs. Proceed to next suspected area shown in Problem Symptoms Table (See page (Click here))
Disc damaged/up side down/dirty When it is determined that any of the following is the cause of the disc read error:
·

The disc cannot be read.

·

The disc cannot be read because of dirt or scratches.

·

The disc cannot be read because it is inserted up side down.


Cannot determine disc type An unsuitable disc is inserted.
DPS error When an error occurs while decoding MP3/WMA files.
Some files are corrupt
·

When MP3/WMA files cannot be played back because they are unsupported.

·

Even though the file extensions are MP3 or WMA, files cannot be played back because the header information cannot be read.


Some files cannot be found
·

When a disc without music data is played back.

·

When there are no playable MP3/WMA files.


Copy protection violation When a file with copyright protection that cannot be played back is played back.

"Device" Screen Description
Device Component
DVD-P Multi-media module receiver assembly
CD-P Not available
R-Seat DVD-P Not available

HINT:
·

Optical Disc Error History can store up to 7 history data items. If a new optical disc error occurs when 7 data items have already been stored, the oldest data is cleared and the new data is stored.

·

If an error that is unsupported by the intelligent tester occurs, a "-" or blank is displayed for the display items.





b.

Clear optical disc error history.

i.

When DTCs are cleared using any of the following operations, Optical Disc Error History will be cleared as well (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(w/ Navigation System)>DTC CHECK / CLEAR).

·

Cleared using the intelligent tester.

·

Cleared using the system check mode screen.

·

Cleared using the unit check mode screen.