Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/ Navigation System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255478 AUDIO AND VISUAL SYSTEM(w/ Navigation System) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/ Navigation System)  Multi-display Power Source Circuit  


DESCRIPTION

This circuit provides power to the multi-display assembly.

WIRING DIAGRAM

C260265E13
5.5,0.771 5.917,0.917 0.417,0.146 10 false +B2 5.5,1.365 5.917,1.51 0.417,0.146 10 false ACC 5.5,1.958 5.917,2.104 0.417,0.146 10 false IG 5.5,2.521 5.917,2.667 0.417,0.146 10 false GND1 5.24,0.688 5.656,0.833 0.417,0.146 10 false 12 5.25,1.271 5.667,1.417 0.417,0.146 10 false 24 5.25,1.854 5.667,2 0.417,0.146 10 false 23 5.25,2.438 5.667,2.583 0.417,0.146 10 false 13 3.833,0.969 4.177,1.219 0.344,0.25 10 false TV 3.802,1.521 4.635,1.75 0.833,0.229 10 false ACC 3.542,2.115 4.521,2.323 0.979,0.208 10 false ECU-IG No. 1 5.25,2.938 5.667,3.083 0.417,0.146 10 false F79 5.25,3.104 6.833,3.333 1.583,0.229 10 false Multi-display Assembly 1.365,0.76 2.365,1.01 1,0.25 10 false from Battery 1.146,1.354 2.396,1.604 1.25,0.25 10 false from ACC Relay 0.896,1.938 2.479,2.188 1.583,0.25 10 false from IG1 NO.1 Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - BATTERY AND BODY GROUND)
a.
U166271E01
1.551,0.282 1.853,0.439 0.302,0.157 10 F79 1.321,1.821 1.738,1.977 0.416,0.156 10 IG 2.058,1.894 2.475,2.050 0.416,0.156 10 ACC 2.508,1.396 2.611,1.988 2.611,1.988 2.465,1.988 false 2.887,1.34 3.227,1.496 0.340,0.156 10 +B2 2.56,1.21 2.744,1.426 2.744,1.426 2.855,1.426 false 2.336,1.374 1.656,1.907 1.656,1.907 1.545,1.907 false 0.057,1.612 0.473,1.768 0.416,0.156 10 GND1 0.057,0.059 0.251,0.215 0.194,0.156 10 *a 0.859,1.384 0.651,1.698 0.651,1.698 0.568,1.698 false

Disconnect the multi-display assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-13 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F79-12 (+B2) - Body ground Always 11 to 14 V
F79-23 (IG) - Body ground Engine switch on (IG) 11 to 14 V
F79-24 (ACC) - Body ground Engine switch on (ACC) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Multi-display Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR