Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/o Navigation System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255479 AUDIO AND VISUAL SYSTEM(w/o Navigation System) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/o Navigation System)  Sound Signal Circuit between Radio Receiver and Stereo Component Amplifier  


DESCRIPTION

The radio receiver assembly sends sounds signal to the stereo component amplifier assembly through this circuit.

The sound signal that has been sent is amplified by the stereo component amplifier assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.

WIRING DIAGRAM

E194161E01
0.073,3.955 0.437,4.148 0.364,0.193 10 F18 0.078,4.127 2.569,4.267 2.492,0.140 10 Stereo Component Amplifier Assembly 3.223,3.973 3.925,4.166 0.702,0.193 10 (Shielded) 0.89,1.223 1.111,1.467 0.221,0.244 10 L- 1.208,1.104 1.401,1.301 0.193,0.198 10 2 0.858,1.966 1.097,2.192 0.239,0.225 10 L+ 1.203,1.82 1.354,2.018 0.151,0.198 10 3 0.878,2.698 1.095,2.910 0.217,0.211 10 R- 1.194,2.573 1.410,2.774 0.216,0.201 10 4 0.858,3.427 1.083,3.564 0.225,0.137 10 R+ 1.179,3.301 1.289,3.446 0.110,0.144 10 5 5.453,3.955 5.827,4.092 0.373,0.137 10 F1 5.458,4.127 7.118,4.316 1.661,0.188 10 Radio Receiver Assembly 5.82,0.361 6.069,0.516 0.249,0.155 10 10 5.831,1.092 6.015,1.276 0.184,0.184 10 19 5.892,1.83 6.131,2.004 0.239,0.174 10 9 5.827,2.554 6.047,2.747 0.221,0.193 10 18 5.883,3.292 6.093,3.539 0.210,0.247 10 8 6.177,0.517 6.657,0.720 0.480,0.202 10 SLD 6.2,1.237 6.430,1.430 0.230,0.193 10 L- 6.196,1.97 6.416,2.191 0.221,0.221 10 L+ 6.186,2.694 6.444,2.914 0.258,0.221 10 R- 6.186,3.441 6.425,3.680 0.239,0.239 10 R+

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY- STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the F1 radio receiver assembly and F18 stereo component amplifier assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-9 (L+) - F18-3 (L+) Always Below 1 Ω
F1-19 (L-) - F18-2 (L-) Always Below 1 Ω
F1-8 (R+) - F18-5 (R+) Always Below 1 Ω
F1-18 (R-) - F18-4 (R-) Always Below 1 Ω
F1-9 (L+) - Body ground Always 10 kΩ or higher
F1-19 (L-) - Body ground Always 10 kΩ or higher
F1-8 (R+) - Body ground Always 10 kΩ or higher
F1-18 (R-) - Body ground Always 10 kΩ or higher
F1-10 (SLD) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR