Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/o Navigation System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255479 AUDIO AND VISUAL SYSTEM(w/o Navigation System) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/o Navigation System)  Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends sound signal from an external device to the radio receiver assembly through this circuit.

The sound signal that has been sent is amplified by the stereo component amplifier assembly or radio receiver assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly, radio receiver assembly or speakers.

WIRING DIAGRAM

E194164E02
0.109,3.333 2.439,3.494 2.330,0.161 10 No. 1 Stereo Jack Adapter Assembly 5.49,3.102 5.810,3.253 0.320,0.151 10 F19 5.49,3.259 7.100,3.439 1.610,0.180 10 Radio Receiver Assembly 3.239,2.878 3.960,3.045 0.721,0.167 10 (Shielded) 0.614,0.368 1.097,0.554 0.483,0.185 10 AUXO 0.711,0.965 1.135,1.180 0.424,0.214 10 ARO 0.734,1.579 1.094,1.751 0.359,0.172 10 ALO 0.622,2.196 1.084,2.444 0.461,0.248 10 ASGN 0.617,2.793 1.042,2.996 0.424,0.202 10 AGND 6.14,0.37 6.504,0.525 0.364,0.156 10 AUXI 6.14,0.972 6.601,1.193 0.461,0.221 10 ARI 6.159,1.565 6.491,1.749 0.332,0.184 10 ALI 6.154,2.177 6.615,2.435 0.461,0.258 10 ASGN 6.168,2.793 6.713,2.996 0.545,0.202 10 AGND 5.853,0.263 6.074,0.521 0.221,0.258 10 19 5.848,0.865 6.125,1.067 0.276,0.202 10 15 5.848,1.458 6.088,1.642 0.239,0.184 10 17 5.839,2.079 6.097,2.245 0.258,0.165 10 16 5.848,2.682 6.106,2.903 0.258,0.221 10 18 4.584,2.892 5.305,3.059 0.721,0.167 10 (Shielded) 1.896,2.906 2.617,3.073 0.721,0.167 10 (Shielded) 0.109,3.191 0.360,3.352 0.251,0.162 10 m1 1.145,0.266 1.365,0.524 0.221,0.258 10 8 1.15,0.886 1.371,1.143 0.221,0.258 10 5 1.152,1.5 1.373,1.758 0.221,0.258 10 6 1.14,2.111 1.361,2.369 0.221,0.258 10 7 1.14,2.705 1.361,2.963 0.221,0.258 10 9

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the m1 No. 1 stereo jack adapter assembly and F19 radio receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
m1-8 (AUXO) - F19-19 (AUXI) Always Below 1 Ω
m1-7 (ASGN) - F19-16 (ASGN) Always Below 1 Ω
m1-5 (ARO) - F19-15 (ARI) Always Below 1 Ω
m1-6 (ALO) - F19-17 (ALI) Always Below 1 Ω
m1-9 (AGND) - F19-18 (AGND) Always Below 1 Ω
m1-8 (AUXO) - Body ground Always 10 kΩ or higher
m1-7 (ASGN) - Body ground Always 10 kΩ or higher
m1-5 (ARO) - Body ground Always 10 kΩ or higher
m1-6 (ALO) - Body ground Always 10 kΩ or higher
m1-9 (AGND) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR