Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/o Navigation System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255479 AUDIO AND VISUAL SYSTEM(w/o Navigation System) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/o Navigation System)  Sound Signal Circuit between Radio Receiver and Multi-media Interface ECU  


DESCRIPTION

The multi-media interface ECU sends sound signals to the radio receiver assembly through this circuit.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly, radio receiver assembly or speakers.

WIRING DIAGRAM

E180193E07
1.009,0.534 1.423,0.708 0.414,0.173 10 USD1 1.009,1.013 1.423,1.186 0.414,0.173 10 URO+ 1.009,1.499 1.423,1.672 0.414,0.173 10 URO- 1.009,1.971 1.423,2.144 0.414,0.173 10 ULO+ 1.009,2.447 1.423,2.620 0.414,0.173 10 ULO- 1.452,0.427 1.640,0.600 0.187,0.173 10 1 1.462,0.945 1.649,1.119 0.187,0.173 10 2 1.462,1.408 1.649,1.581 0.187,0.173 10 3 1.462,1.889 1.649,2.062 0.187,0.173 10 4 1.457,2.365 1.644,2.538 0.187,0.173 10 5 5.805,0.525 6.270,0.698 0.465,0.173 10 CSLD 5.805,1.02 6.270,1.193 0.465,0.173 10 CDR+ 5.805,1.515 6.270,1.689 0.465,0.173 10 CDR- 5.805,1.959 6.270,2.132 0.465,0.173 10 CDL+ 5.805,2.459 6.270,2.632 0.465,0.173 10 CDL- 5.642,0.45 5.829,0.624 0.187,0.173 10 1 5.644,0.95 5.832,1.123 0.187,0.173 10 2 5.644,1.412 5.832,1.585 0.187,0.173 10 3 5.658,1.889 5.845,2.062 0.187,0.173 10 4 5.66,2.365 5.847,2.538 0.187,0.173 10 5 5.504,2.874 5.983,3.059 0.479,0.185 10 F55 4.292,2.72 4.979,2.905 0.687,0.185 10 (Shielded) 2.251,2.72 2.938,2.905 0.687,0.185 10 (Shielded) 0.425,2.86 0.674,3.045 0.249,0.185 10 L40 0.425,3.028 2.153,3.254 1.728,0.225 10 Multi-media Interface ECU 5.504,3.063 7.127,3.251 1.623,0.187 10 Radio Receiver Assembly

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MULTI-MEDIA INTERFACE ECU)
a.

Disconnect the F55 radio receiver assembly and L40 multi-media interface ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L40-1 (USD1) - F55-1 (CSLD) Always Below 1 Ω
L40-2 (URO+) - F55-2 (CDR+) Always Below 1 Ω
L40-3 (URO-) - F55-3 (CDR-) Always Below 1 Ω
L40-4 (ULO+) - F55-4 (CDL+) Always Below 1 Ω
L40-5 (ULO-) - F55-5 (CDL-) Always Below 1 Ω
L40-1 (USD1) - Body ground Always 10 kΩ or higher
L40-2 (URO+) - Body ground Always 10 kΩ or higher
L40-3 (URO-) - Body ground Always 10 kΩ or higher
L40-4 (ULO+) - Body ground Always 10 kΩ or higher
L40-5 (ULO-) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR