Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255487 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Radio Receiver Power Source Circuit  


DESCRIPTION

This circuit provides power to the radio and display receiver assembly.

WIRING DIAGRAM

E282609E22
1.031,0.344 1.865,0.542 0.833,0.198 10 false from Battery 0.49,0.813 1.854,1 1.365,0.188 10 false from IG1 NO. 2 Relay 0.802,1.302 1.906,1.5 1.104,0.198 10 false from ACC Relay 3.146,0.521 3.917,0.698 0.771,0.177 10 false RADIO 2.958,0.969 4.344,1.198 1.385,0.229 10 false ECU-IG NO.3 3.063,1.5 3.833,1.677 0.771,0.177 10 false ECU-ACC 5.323,0.354 5.771,0.531 0.448,0.177 10 false F120 5.323,0.823 5.771,1 0.448,0.177 10 false F124 5.323,1.313 5.771,1.49 0.448,0.177 10 false F120 5.333,1.75 5.781,1.927 0.448,0.177 10 false F120 5.417,0.156 5.563,0.354 0.146,0.198 10 false 4 5.406,0.615 5.552,0.813 0.146,0.198 10 false 1 5.427,1.104 5.573,1.302 0.146,0.198 10 false 3 5.427,1.542 5.573,1.74 0.146,0.198 10 false 7 5.729,1.781 6.177,1.958 0.448,0.177 10 false GND1 5.729,1.323 6.177,1.5 0.448,0.177 10 false ACC1 5.719,0.844 6.167,1.021 0.448,0.177 10 false IG 5.708,0.385 6.156,0.563 0.448,0.177 10 false +B1 5.615,2.156 6.896,2.51 1.281,0.354 10 false Radio and Display Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuse for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U166449E01
0.03,0.056 0.438,0.240 0.408,0.184 10 *a 1.456,0.376 1.816,0.560 0.359,0.184 10 F120 2.517,0.427 2.927,0.611 0.410,0.184 10 ACC1 2.788,0.845 3.100,1.029 0.312,0.184 10 +B1 2.008,1.134 2.228,0.51 2.228,0.51 2.494,0.51 false 2.012,1.974 2.420,2.158 0.408,0.184 10 GND1 1.548,1.639 1.723,2.057 1.723,2.057 1.989,2.057 false 2.266,1.13 2.513,0.932 2.513,0.932 2.779,0.932 false 1.508,2.433 1.868,2.617 0.359,0.184 10 F124 0.193,2.707 0.424,2.890 0.231,0.184 10 IG 0.777,3.411 0.597,2.794 0.597,2.794 0.451,2.794 false

Disconnect the radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F120-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F120-4 (+B1) - Body ground Always 11 to 14 V
F120-3 (ACC1) - Body ground Engine switch on (ACC) 11 to 14 V
F124-1 (IG) - Body ground Engine switch on (IG) 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR