Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2015.08–2017.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255487 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Sound Signal Circuit between Radio Receiver and Stereo Component Amplifier  


DESCRIPTION

The radio and display receiver assembly sends a sound signal to the stereo component amplifier assembly via this circuit.

The sound signal that has been sent is amplified by the stereo component amplifier assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.

WIRING DIAGRAM

E284138E05
0.281,3.49 0.938,3.635 0.656,0.146 10 false F120 0.281,3.656 1.521,4.333 1.24,0.677 10 false Radio and Display Receiver Assembly 5.625,3.49 6.281,3.635 0.656,0.146 10 false F18 5.958,2.969 6.271,3.115 0.313,0.146 10 false SLD 5.958,2.302 6.323,2.656 0.365,0.354 10 false L- 5.958,1.823 6.271,1.969 0.313,0.146 10 false L+ 5.958,1.229 6.271,1.375 0.313,0.146 10 false R- 5.958,0.583 6.271,0.729 0.313,0.146 10 false R+ 5.74,2.917 6.052,3.063 0.313,0.146 10 false 6 5.74,2.333 6.052,2.479 0.313,0.146 10 false 2 5.74,1.719 6.052,1.865 0.313,0.146 10 false 3 5.74,1.135 6.052,1.281 0.313,0.146 10 false 4 5.74,0.479 6.052,0.625 0.313,0.146 10 false 5 1.344,2.302 1.656,2.448 0.313,0.146 10 false 6 3.323,3.198 4.01,3.344 0.688,0.146 10 false Shielded 1.344,1.708 1.656,1.854 0.313,0.146 10 false 2 1.344,1.115 1.656,1.26 0.313,0.146 10 false 5 1.344,0.427 1.656,0.573 0.313,0.146 10 false 1 0.927,2.438 1.24,2.583 0.313,0.146 10 false FL- 0.927,1.875 1.24,2.021 0.313,0.146 10 false FL+ 0.927,1.271 1.24,1.417 0.313,0.146 10 false FR- 0.927,0.625 1.24,0.771 0.313,0.146 10 false FR+ 5.615,3.677 6.854,4.354 1.24,0.677 10 false Stereo Component Amplifier Assembly

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the F18 stereo component amplifier assembly connector.


b.

Disconnect the F120 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F120-1 (FR+) - F18-5 (R+) Always Below 1 Ω
F120-2 (FL+) - F18-3 (L+) Always Below 1 Ω
F120-5 (FR-) - F18-4 (R-) Always Below 1 Ω
F120-6 (FL-) - F18-2 (L-) Always Below 1 Ω
F18-6 (SLD) - Body ground Always 10 kΩ or higher
F120-1 (FR+) - Body ground Always 10 kΩ or higher
F120-2 (FL+) - Body ground Always 10 kΩ or higher
F120-5 (FR-) - Body ground Always 10 kΩ or higher
F120-6 (FL-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR