Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255487 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  USB Audio System Recognition/Play Error  


WIRING DIAGRAM

E280102E31
6.135,0.406 6.563,0.583 0.427,0.177 10 false USV1 5.938,0.302 6.063,0.479 0.125,0.177 10 false 1 6.135,0.844 6.563,1.021 0.427,0.177 10 false UGD1 5.938,0.74 6.063,0.917 0.125,0.177 10 false 4 6.135,1.729 6.563,1.906 0.427,0.177 10 false US1+ 5.938,1.625 6.063,1.802 0.125,0.177 10 false 3 5.802,2.5 6.229,2.677 0.427,0.177 10 false A 5.792,2.677 7.073,3.052 1.281,0.375 10 false Radio and Display Receiver Assembly 0.167,2.552 0.49,2.729 0.323,0.177 10 false B 0.167,2.74 1.375,3.115 1.208,0.375 10 false No. 1 Stereo Jack Adapter Assembly 0.688,0.417 1.073,0.604 0.385,0.188 10 false USV1 0.646,0.875 1.063,1.052 0.417,0.177 10 false UGD1 0.708,1.729 1.052,1.938 0.344,0.208 10 false US1+ 1.188,0.281 1.313,0.458 0.125,0.177 10 false 1 1.188,0.719 1.313,0.896 0.125,0.177 10 false 4 6.135,2.167 6.563,2.344 0.427,0.177 10 false USG1 5.938,2.063 6.063,2.24 0.125,0.177 10 false 5 0.688,2.177 1.115,2.375 0.427,0.198 10 false USG1 1.188,2.042 1.313,2.219 0.125,0.177 10 false 5 1.188,1.604 1.333,1.792 0.146,0.188 10 false 3 4.26,2.302 4.906,2.479 0.646,0.177 10 false Shielded 2.333,2.302 2.979,2.479 0.646,0.177 10 false Shielded 6.135,1.281 6.563,1.458 0.427,0.177 10 false US1- 0.708,1.313 1.104,1.49 0.396,0.177 10 false US1- 5.938,1.188 6.063,1.365 0.125,0.177 10 false 2 1.188,1.167 1.313,1.344 0.125,0.177 10 false 2

CAUTION / NOTICE / HINT

HINT:
·

When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).

·

When a large amount of data is in a USB device, it may take a while before play begins.

·

When using a USB device, files that are copy protected or encrypted due to copyright reasons cannot be played.

·

When files are not played in the sorted order, perform the following procedure before inspection.

(a)

Add numbers in front of the file names.

(b)

Put the files in a folder and copy the folder data to the USB device.




PROCEDURE

1.CHECK USB DEVICE OR "iPod"
a.

Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.


b.

Check if playable files are present on the USB device or "iPod".

HINT:

Refer to System Description for playable files (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>SYSTEM DESCRIPTION).



c.

Check if the USB device is a compatible format or "iPod" is a compatible version.

HINT:

Refer to System Description for compatible formats and versions (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>SYSTEM DESCRIPTION).


Result
Result Proceed to
No playable files exist, or incompatible device format or version. A
Playable files exist, and compatible device format or version. B



A

USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION WAS INCOMPATIBLE, OR NO PLAYABLE FILES PRESENT

B

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the A radio and display receiver assembly connector.


b.

Disconnect the B No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (USV1) - B-1 (USV1) Always Below 1 Ω
A-2 (US1-) - B-2 (US1-) Always Below 1 Ω
A-3 (US1+) - B-3 (US1+) Always Below 1 Ω
A-4 (UGD1) - B-4 (UGD1) Always Below 1 Ω
A-5 (UGS1) - B-5 (UGS1) Always Below 1 Ω
A-1 (USV1) - Body ground Always 10 kΩ or higher
A-2 (US1-) - Body ground Always 10 kΩ or higher
A-3 (US1+) - Body ground Always 10 kΩ or higher
A-4 (UGD1) - Body ground Always 10 kΩ or higher
A-5 (USG1) - Body ground Always 10 kΩ or higher




OK

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Reconnect the radio and display receiver assembly connector.


b.
U166444E02
0.885,0.438 1.135,0.438 1.135,0.438 1.479,0.854 false 2.5,0.438 2.25,0.438 2.25,0.438 1.906,0.854 false 0.708,0.958 1.063,1.156 0.354,0.198 10 false B 0.427,0.354 0.844,0.542 0.417,0.188 10 false USV1 0.052,0.073 0.354,0.26 0.302,0.188 10 false *a 2.531,0.333 2.99,0.521 0.458,0.188 10 false UGD1

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B-1 (USV1) - B-4 (UGD1) Engine switch on (ACC) 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)



OK

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK
a.

Delete all files in the USB device or "iPod" and format/restore it.


b.

Save the data again and check if it can be played on the in-vehicle device.

NOTICE:

Formatting a USB device or restoring an "iPod" erases all music on the device.

Ensure that backup music data is available before performing this operation.


OK:

Malfunction disappears.




OK

END (USB DEVICE OR "iPod" IS DEFECTIVE)

NG

5.REPLACE USB DEVICE OR "iPod"
5.REPLACE USB DEVICE OR "iPod"
a.

Turn the engine switch off.

HINT:

When this malfunction occurs, it is necessary to turn off the engine switch to make it possible for the vehicle to recognize a new device when it is connected.



b.

Turn the engine switch on (ACC).


c.

Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.

HINT:
·

If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.

·

Refer to System Description for compatible formats and versions (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>SYSTEM DESCRIPTION).





NEXT

6.CHECK USB DEVICE OR "iPod"
6.CHECK USB DEVICE OR "iPod"
a.

Check if the USB device or "iPod" is recognized by the radio and display receiver assembly, or if information such as track, artist and album names are displayed on the screen.

OK:

USB device or "iPod" is recognized or track information such as track, artist and album names are displayed.




OK

USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE

NG