Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (w/ Multi-display) › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255488 AUDIO AND VISUAL SYSTEM(w/ Multi-display) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/ Multi-display)  Radio Receiver Power Source Circuit  


DESCRIPTION

This circuit provides power to the multi-media module receiver assembly.

WIRING DIAGRAM

E263382E08
5.684,0.679 5.976,0.844 0.292,0.165 10 +B1 5.684,1.855 6.066,2.020 0.383,0.165 10 IG 5.684,2.442 6.136,2.607 0.452,0.165 10 GND1 5.684,1.267 6.150,1.432 0.466,0.165 10 ACC1 5.357,2.336 5.581,2.501 0.224,0.165 10 12 5.357,1.762 5.581,1.927 0.224,0.165 10 15 5.357,0.578 5.581,0.743 0.224,0.165 10 17 5.357,1.173 5.581,1.339 0.224,0.165 10 16 3.682,2.024 4.642,2.201 0.960,0.177 10 ECU-IG1 NO.3 3.887,0.824 4.390,1.000 0.502,0.177 10 RADIO 1.485,0.679 2.309,0.848 0.824,0.169 10 from Battery 0.949,1.838 2.759,2.032 1.811,0.193 10 from IG1 NO.2 Relay 1.242,1.245 2.487,1.443 1.244,0.199 10 from ACC Relay 5.334,2.979 6.660,3.304 1.326,0.325 10 Multi-media Module Receiver Assembly 5.334,2.82 5.757,2.994 0.423,0.174 10 F77 3.776,1.43 4.468,1.591 0.692,0.161 10 ECU-ACC

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY -BATTERY AND BODY GROUND)
a.
U166614E01
0.123,0.076 0.309,0.234 0.186,0.158 10 *a 2.879,0.474 3.325,0.632 0.446,0.158 10 ACC1 2.114,1.84 2.560,1.998 0.446,0.158 10 +B1 1.134,1.672 1.581,1.831 0.446,0.158 10 GND1 2.724,0.13 3.170,0.288 0.446,0.158 10 IG 1.537,0.345 1.822,0.503 0.285,0.158 10 F77 2.687,1.004 2.733,0.553 2.733,0.553 2.84,0.553 false 2.801,1.077 2.569,1.923 2.569,1.923 2.436,1.923 false 2.086,1.094 1.762,1.752 1.762,1.752 1.628,1.752 false 2.498,1.004 2.6,0.209 2.6,0.209 2.69,0.209 false

Disconnect the multi-media module receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-12 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F77-15 (IG) - Body ground Engine switch on (IG) 11 to 14 V
F77-16 (ACC1) - Body ground Engine switch on (ACC) 11 to 14 V
F77-17 (+B1) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Multi-media Module Receiver Assembly)


OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR