Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (w/ Multi-display) › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255488 AUDIO AND VISUAL SYSTEM(w/ Multi-display) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/ Multi-display)  Multi-display Power Source Circuit  


DESCRIPTION

This circuit provides power to the multi-display assembly.

WIRING DIAGRAM

E263384E06
5.501,0.745 5.794,0.910 0.292,0.165 10 B 5.501,1.92 5.884,2.085 0.383,0.165 10 IG 5.501,2.508 5.954,2.673 0.452,0.165 10 GND1 5.501,1.332 5.967,1.498 0.466,0.165 10 ACC 5.175,2.416 5.399,2.581 0.224,0.165 10 13 5.175,1.827 5.399,1.993 0.224,0.165 10 23 5.175,0.644 5.399,0.809 0.224,0.165 10 12 5.175,1.239 5.399,1.404 0.224,0.165 10 24 3.489,2.08 4.584,2.257 1.095,0.177 10 ECU-IG1 NO.3 3.732,0.885 4.622,1.061 0.890,0.177 10 RADIO 1.328,0.73 2.133,0.907 0.805,0.177 10 from Battery 0.764,1.918 2.101,2.123 1.338,0.205 10 from IG1 NO.2 Relay 1.07,1.312 2.325,1.509 1.255,0.196 10 from ACC Relay 5.315,3.079 6.797,3.269 1.482,0.190 10 Multi-display Assembly 5.315,2.92 5.825,3.094 0.510,0.174 10 F79 3.615,1.487 4.309,1.638 0.694,0.151 10 ECU-ACC

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - BATTERY AND BODY GROUND)
a.
U166273E01
1.576,0.228 1.906,0.385 0.330,0.157 10 F79 1.321,1.821 1.738,1.977 0.416,0.156 10 IG 2.058,1.894 2.475,2.050 0.416,0.156 10 ACC 2.508,1.396 2.611,1.988 2.611,1.988 2.465,1.988 false 2.887,1.34 3.304,1.496 0.416,0.156 10 B 2.56,1.21 2.744,1.426 2.744,1.426 2.855,1.426 false 2.336,1.374 1.656,1.907 1.656,1.907 1.545,1.907 false 0.057,1.612 0.473,1.768 0.416,0.156 10 GND1 0.057,0.059 0.251,0.215 0.194,0.156 10 *a 0.859,1.384 0.651,1.698 0.651,1.698 0.568,1.698 false

Disconnect the multi-display assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-13 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F79-12 (B) - Body ground Always 11 to 14 V
F79-23 (IG) - Body ground Engine switch on (IG) 11 to 14 V
F79-24 (ACC) - Body ground Engine switch on (ACC) 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Multi-display Assembly)


OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR