Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255497 TOYOTA PARKING ASSIST-SENSOR SYSTEM U

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  TERMINALS OF ECU  


CHECK PARK ASSIST ECU (w/ Side Monitor System)


U166300E02
4.771,0.313 5.094,0.531 0.323,0.219 10 false F75 3.24,0.323 3.542,0.51 0.302,0.188 10 false F76 2,0.323 2.313,0.521 0.313,0.198 10 false F88

a.

Disconnect the F75 and F76 parking assist ECU connectors.


b.

Measure the voltage and resistance according to value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F75-1 (+B) - F75-4 (GND1) L - W-B Power source signal Always 11 to 14 V
F75-4 (GND1) - Body ground W-B - Body ground Ground Always Below 1 Ω
F76-25 (CSSW) - F75-4 (GND1) Y - W-B back sonar or clearance sonar switch assembly power source signal Engine switch on (IG), back sonar or clearance sonar switch assembly on 11 to 14 V
Engine switch on (IG), back sonar or clearance sonar switch assembly off Below 1 V
F75-8 (IG) - F75-4 (GND1) G - W-B IG power source signal Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
F75-9 (ACC) - F75-4 (GND1) GR - W-B ACC power source signal Engine switch on (ACC) 11 to 14 V
Engine switch off Below 1 V


c.

Reconnect the F75 and F76 parking assist ECU connectors.


d.

Measure the voltage and waveform according to value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F76-3 (LIN2) - F76-4 (CSG2) LG - GR Rear sensor circuit power source Engine switch on (IG), back sonar or clearance sonar switch assembly on Waveform 1
F76-5 (CSB1) - F76-6 (CSG1) GR - R Front sensor circuit power source Engine switch off Below 1 V
Engine switch on (IG), back sonar or clearance sonar switch assembly on 7.2 to 8.8 V
F75-6 (EF) - F75-7 (BBZ) L - G No. 1 clearance warning buzzer signal Buzzer does not sound Below 1 V
Buzzer sounding Waveform 2
F76-20 (CSB2) - F76-4 (CSG2) R - GR Rear sensor circuit power source Engine switch on (IG), back sonar or clearance sonar switch assembly on 7.2 to 8.8 V
Engine switch off Below 1 V
F76-23 (LIN1) - F76-6 (CSG1) LG - R Front sensor circuit power source Engine switch on (IG), back sonar or clearance sonar switch assembly on Waveform 1


e.
E349716E01
0.104,0.604 0.521,0.813 0.417,0.208 10 false CH: 1 0.115,0.979 0.573,1.177 0.458,0.198 10 false GND 0.146,1.583 0.604,1.781 0.458,0.198 10 false GND 0.094,1.292 0.552,1.49 0.458,0.198 10 false CH: 2

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Terminal No. (Symbol)
·

F76-3 (LIN2) - F76-4 (CSG2)

·

F76-23 (LIN1) - F76-6 (CSG1)


Tool Setting 2 V/DIV., 1 msec./DIV.
Condition Engine switch on (IG), back sonar or clearance sonar switch assembly on


f.
E349717E01
2.938,1.667 3.396,1.865 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 2.

Waveform 2 (Reference)
Item Content
Terminal No. (Symbol) F75-6 (EF) - F75-7 (BBZ)
Tool Setting 5 V/DIV., 1 msec./DIV.
Condition Engine switch on (IG), shift lever moved to R

NOTICE:

The waveform amplitude varies depending on the volume setting.




CHECK CLEARANCE WARNING ECU ASSEMBLY (w/o Side Monitor System)


U165788E02
3.354,0.573 3.635,0.844 0.281,0.271 10 false F12

a.

Disconnect the F12 clearance warning ECU assembly connector.


b.

Measure the voltage and resistance according to value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F12-12 (CSSW) - F12-17 (GND1) Y - W-B back sonar or clearance sonar switch assembly power source signal Engine switch on (IG), back sonar or clearance sonar switch assembly on 11 to 14 V
Engine switch on (IG), back sonar or clearance sonar switch assembly off Below 1 V
F12-15 (IG) - F12-17 (GND1) G - W-B IG power source signal Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
F12-17 (GND1) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the F12 clearance warning ECU assembly connector.


d.

Measure the voltage and waveform according to value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F12-7 (CSB2) - F12-18 (CSG2) R - GR Rear sensor circuit power source Engine switch on (IG), back sonar or clearance sonar switch assembly on 7.2 to 8.8 V
Engine switch off Below 1 V
F12-9 (LIN1) - F12-19 (CSG1) LG - R Front sensor circuit power source Engine switch on (IG), back sonar or clearance sonar switch assembly on Waveform 1
F12-10 (BBZ) - F12-11 (EF) G - L No. 1 clearance warning buzzer signal Buzzer not sounding Below 1 V
Buzzer sounding Waveform 2
F12-21 (CSB1) - F12-9 (LIN1) GR - LG Front sensor circuit power source Engine switch on (IG), back sonar or clearance sonar switch assembly on 7.2 to 8.8 V
Engine switch off Below 1 V
F12-24 (LIN2) - F12-18 (CSG2) LG - GR Rear sensor circuit power source Engine switch on (IG), back sonar or clearance sonar switch assembly on Waveform 1


e.
E349716E01
0.104,0.604 0.521,0.813 0.417,0.208 10 false CH: 1 0.115,0.979 0.573,1.177 0.458,0.198 10 false GND 0.146,1.583 0.604,1.781 0.458,0.198 10 false GND 0.094,1.292 0.552,1.49 0.458,0.198 10 false CH: 2

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Terminal No. (Symbol)
·

F12-9 (LIN1) - F12-19 (CSG1)

·

F12-24 (LIN2) - F12-18 (CSG2)


Tool Setting 2 V/DIV., 1 msec./DIV.
Condition Engine switch on (IG), back sonar or clearance sonar switch assembly on


f.
E349717E01
2.938,1.667 3.396,1.865 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 2.

Waveform 2 (Reference)
Item Content
Terminal No. (Symbol) F12-10 (BBZ) - F12-11 (EF)
Tool Setting 5 V/DIV., 1 msec./DIV.
Condition Engine switch on (IG), shift lever moved to R

NOTICE:

The waveform amplitude varies depending on the volume setting.