Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255497 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  Clearance Warning Buzzer Circuit  


DESCRIPTION

The No. 1 clearance warning buzzer sounds to alert the driver and the buzzed frequency changes depending on the distance to an obstacle.

WIRING DIAGRAM

E246939E11
5.448,0.625 5.865,0.865 0.417,0.24 10 false BBZ 0.406,1.688 0.688,1.844 0.281,0.156 10 false E10 0.396,1.833 2.542,2.083 2.146,0.25 10 false No. 1 Clearance Warning Buzzer 0.083,0.052 2.302,0.385 2.219,0.333 12 false w/ Side Monitor System: 5.104,2.083 6.51,2.323 1.406,0.24 10 false Parking Assist ECU 5.104,1.938 5.438,2.167 0.333,0.229 10 false F75 5.229,0.531 5.396,0.74 0.167,0.208 10 false 7 5.458,1.406 5.823,1.583 0.365,0.177 10 false EF 5.25,1.323 5.469,1.563 0.219,0.24 10 false 6 1.875,0.542 2.094,0.771 0.219,0.229 10 false 1 1.885,1.323 2.146,1.521 0.26,0.198 10 false 2 1.615,0.542 1.813,0.698 0.198,0.156 10 false Z+ 1.656,1.323 1.854,1.521 0.198,0.198 10 false Z-

E246939E12
5.427,0.594 5.76,0.75 0.333,0.156 10 false BBZ 0.344,1.677 0.625,1.833 0.281,0.156 10 false E10 0.354,1.833 2.448,2.021 2.094,0.188 10 false No. 1 Clearance Warning Buzzer 0.083,0.083 2.771,0.333 2.688,0.25 12 false w/o Side Monitor System: 5.188,2.073 6.438,2.427 1.25,0.354 10 false Clearance Warning ECU Assembly 5.188,1.906 5.458,2.063 0.271,0.156 10 false F12 5.177,0.521 5.354,0.677 0.177,0.156 10 false 10 5.427,1.385 5.76,1.542 0.333,0.156 10 false EF 5.177,1.302 5.354,1.458 0.177,0.156 10 false 11 1.875,0.531 1.99,0.688 0.115,0.156 10 false 1 1.875,1.313 1.99,1.469 0.115,0.156 10 false 2 1.615,0.542 1.813,0.698 0.198,0.156 10 false Z+ 1.656,1.323 1.813,1.479 0.156,0.156 10 false Z-

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (NO. 1 CLEARANCE WARNING BUZZER)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the buzzer operates (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>DATA LIST / ACTIVE TEST).

Clearance Sonar
Tester Display Test Part Control Range Diagnostic Note
Front Buzzer No. 1 clearance warning buzzer Operate or Stop -

OK:

No. 1 clearance warning buzzer sounds.


Result
Result Proceed to
OK A
NG (w/ Side Monitor System) B
NG (w/o Side Monitor System) C



A

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - NO. 1 CLEARANCE WARNING BUZZER)

C

5.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 1 CLEARANCE WARNING BUZZER)
2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - NO. 1 CLEARANCE WARNING BUZZER)
a.

Disconnect the F75 parking assist ECU connector.


b.

Disconnect the E10 No. 1 clearance warning buzzer connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F75-7 (BBZ) - E10-1 (Z+) Always Below 1 Ω
F75-6 (EF) - E10-2 (Z-) Always Below 1 Ω
F75-7 (BBZ) - Body ground Always 10 kΩ or higher
F75-6 (EF) - Body ground Always 10 kΩ or higher




OK

3.REPLACE NO. 1 CLEARANCE WARNING BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE NO. 1 CLEARANCE WARNING BUZZER
a.

Replace the No. 1 clearance warning buzzer with a new or known good one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING BUZZER>REMOVAL).



NEXT

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (NO. 1 CLEARANCE WARNING BUZZER)
4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (NO. 1 CLEARANCE WARNING BUZZER)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the buzzer operates (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>DATA LIST / ACTIVE TEST).

Clearance Sonar
Tester Display Test Part Control Range Diagnostic Note
Front Buzzer No. 1 clearance warning buzzer Operate or Stop -

OK:

No. 1 clearance warning buzzer sounds.




OK

END (NO. 1 CLEARANCE WARNING BUZZER WAS DEFECTIVE)

NG

5.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 1 CLEARANCE WARNING BUZZER)
a.

Disconnect the F12 clearance warning ECU connector.


b.

Disconnect the E10 No. 1 clearance warning buzzer connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F12-10 (BBZ) - E10-1 (Z+) Always Below 1 Ω
F12-11 (EF) - E10-2 (Z-) Always Below 1 Ω
F12-10 (BBZ) - Body ground Always 10 kΩ or higher
F12-11 (EF) - Body ground Always 10 kΩ or higher




OK

6.REPLACE NO. 1 CLEARANCE WARNING BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE NO. 1 CLEARANCE WARNING BUZZER
a.

Replace the No. 1 clearance warning buzzer with a new or known good one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING BUZZER>REMOVAL).



NEXT

7.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (NO. 1 CLEARANCE WARNING BUZZER)
7.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (NO. 1 CLEARANCE WARNING BUZZER)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the buzzer operates (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>DATA LIST / ACTIVE TEST).

Clearance Sonar
Tester Display Test Part Control Range Diagnostic Note
Front Buzzer No. 1 clearance warning buzzer Operate or Stop -

OK:

No. 1 clearance warning buzzer sounds.




OK

END (NO. 1 CLEARANCE WARNING BUZZER WAS DEFECTIVE)

NG