This DTC is stored if the radio and display receiver assembly judges as a result of its self check that the signals or signal lines between the radio and display receiver assembly and the rear television camera assembly are not normal.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1622 | An open or short in the rear television camera signal circuit | ·
Harness or connector ·
Rear television camera assembly ·
Radio and display receiver assembly |
When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Service (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Clear the DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM>DTC CHECK / CLEAR).
Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1622 is not output | A |
| DTC C1622 is output | B |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
Disconnect the F118 radio and display receiver assembly connector.
Disconnect the S31 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F118-11 (CA+) - S31-6 (CB+) | Always | Below 1 Ω |
| F118-12 (V+) - S31-3 (CV+) | Always | Below 1 Ω |
| F118-24 (V-) - S31-2 (CV-) | Always | Below 1 Ω |
| F118-23 (CGND) - S31-5 (CGND) | Always | Below 1 Ω |
| F118-11 (CA+) or S31-6 (CB+) - Body ground | Always | 10 kΩ or higher |
| F118-12 (V+) or S31-3 (CV+) - Body ground | Always | 10 kΩ or higher |
| F118-24 (V-) or S31-2 (CV-) - Body gound | Always | 10 kΩ or higher |
| F118-23 (CGND) or S31-5 (CGND) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the radio and display receiver assembly with the connector still connected (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (w/o Multi-display)>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F118-23 (CGND) - Body ground | Always | Below 1 Ω |
| F118-24 (V-) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F118-11 (CA+) - Body ground | Engine switch on (ACC) | 5.5 to 7.05 V |
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
OK
NG
Remove the radio receiver assembly with the connector still connected (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (w/o Multi-display)>REMOVAL).
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
*b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
The video waveform changes according to the image sent by the rear television camera assembly.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | F118-12 (V+) - F118-23 (CGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | ·
Waveform 1: Engine switch on (IG), shift lever in R, camera lens not covered, displaying an image ·
Waveform 2: Engine switch on (IG), shift lever in R, camera lens covered, blacking out screen |
Waveform is as shown in the illustration.
OK
NG
Replace the rear television camera assembly with a new or normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Rear)>REMOVAL).
NEXT
Clear the DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM>DTC CHECK / CLEAR).
Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1622 is not output | A |
| DTC C1622 is output | B |
A
B