The display signal of the rear television camera assembly is transmitted to the radio and display receiver assembly.
When replacing the radio and display receiver assembly, it is necessary perform the vehicle contract setting for Connected Service (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>PRECAUTION).
Disconnect the F118 radio and display receiver assembly connector.
Disconnect the S31 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F118-12 (V+) - S31-3 (CV+) | Always | Below 1 Ω |
| F118-24 (V-) - S31-2 (CV-) | Always | Below 1 Ω |
| F118-11 (CA+) - S31-6 (CB+) | Always | Below 1 Ω |
| F118-23 (CGND) - S31-5 (CGND) | Always | Below 1 Ω |
| F118-12 (V+) or S31-3 (CV+) - Body ground | Always | 10 kΩ or higher |
| F118-24 (V-) or S31-2 (CV-) - Body ground | Always | 10 kΩ or higher |
| F118-11 (CA+) or S31-6 (CB+) - Body ground | Always | 10 kΩ or higher |
| F118-23 (CGND) or S31-5 (CGND) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the radio and display receiver assembly with the connector connected (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (w/o Multi-display)>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F118-23 (CGND) - Body ground | Always | Below 1 Ω |
| F118-24 (V-) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F118-11 (CA+) - Body ground | Engine switch on (ACC) | 5.5 to 7.05 V |
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
OK
NG
Remove the radio and display receiver assembly with the connector connected (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (w/o Multi-display)>REMOVAL).
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
*b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
Check the waveform of the rear television camera assembly using an oscilloscope.
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.
The video waveform changes according to the image sent by the rear television camera assembly.
| Item | Content |
|---|---|
| Tester No. (Symbol) | F118-12 (V+) - F118-23 (CGND) |
| Tool Setting | 0.2 V/DIV., 50 μS/DIV |
| Condition | Waveform 1: Engine switch on (IG), shift lever in R, camera lens is not covered, displaying an image
Waveform 2: Engine switch on (IG), shift lever in R, camera lens is covered, blacking out the screen |
Waveform is as shown in the illustration.
OK
NG
Replace the radio and display receiver assembly with a new or normally functioning one (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (w/o Multi-display)>REMOVAL).
Check the operation of rear view monitor system.
Rear view monitor system is operated normally.
OK
NG