Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › WIDE VIEW FRONT MONITOR SYSTEM › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255510 WIDE VIEW FRONT MONITOR SYSTEM C

PARK ASSIST / MONITORING  WIDE VIEW FRONT MONITOR SYSTEM  C1681  Front Camera Feedback Malfunction  C1682  Front Camera Current Malfunction  


DESCRIPTION

DTC C1681 is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the front television camera assembly to the parking assist ECU.

DTC C1682 is stored if the parking assist ECU judges as a result of its self check that there is a problem with the current supplied from the front television camera assembly connected to the parking assist ECU.

DTC Code DTC Detection Condition Trouble Area
C1681 Front television camera power supply failure
·

Harness or connector

·

Front television camera assembly

·

Parking assist ECU


C1682 An open or short in the front television camera signal circuit

WIRING DIAGRAM

E245723E08
5.021,0.24 5.448,0.417 0.427,0.177 10 false BCB+ 4.656,0.25 4.948,0.469 0.292,0.219 10 false F76 4.698,0.042 4.875,0.198 0.177,0.156 10 false 11 4.656,0.656 4.948,0.854 0.292,0.198 10 false F76 4.698,0.448 4.875,0.604 0.177,0.156 10 false 12 4.656,1.042 4.938,1.281 0.281,0.24 10 false F76 4.698,0.854 4.875,1.031 0.177,0.177 10 false 36 4.656,1.448 4.958,1.656 0.302,0.208 10 false F76 4.719,1.26 4.896,1.417 0.177,0.156 10 false 35 4.656,1.865 4.958,2.094 0.302,0.229 10 false F75 4.74,1.677 4.917,1.885 0.177,0.208 10 false 4 5.021,0.667 5.448,0.844 0.427,0.177 10 false BCV+ 5.021,1.063 5.438,1.26 0.417,0.198 10 false BCV- 5.021,1.458 5.479,1.677 0.458,0.219 10 false BGND 1.719,0.24 2.188,0.438 0.469,0.198 10 false BCB+ 1.719,0.656 2.177,0.906 0.458,0.25 10 false BCV+ 1.719,1.052 2.156,1.25 0.438,0.198 10 false BCV- 1.698,1.448 2.167,1.688 0.469,0.24 10 false BGND 2.219,0.146 2.406,0.344 0.188,0.198 10 false 1 2.219,0.563 2.365,0.781 0.146,0.219 10 false 2 2.219,0.958 2.344,1.115 0.125,0.156 10 false 4 2.219,1.365 2.344,1.542 0.125,0.177 10 false 3 5.021,1.854 5.479,2.031 0.458,0.177 10 false GND1 4.938,2.167 6.198,2.385 1.26,0.219 10 false Parking Assist ECU 0.76,1.74 1.125,2.01 0.365,0.271 10 false A55 0.75,1.896 2.292,2.302 1.542,0.406 10 false Front Television Camera Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When "System initializing" is displayed on the parking assist ECU after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as wide view front monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)>CALIBRATION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY AND BODY GROUND)
a.

Disconnect the F75 and F76 parking assist ECU connectors.


b.

Disconnect the A55 front television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F76-36 (BCV-) - A55-4 (BCV-) Always Below 1 Ω
F76-12 (BCV+) - A55-2 (BCV+) Always Below 1 Ω
F76-35 (BGND) - A55-3 (BGND) Always Below 1 Ω
F76-11 (BCB+) - A55-1 (BCB+) Always Always
F75-4 (GND1) - Body ground Always Always
F76-36 (BCV-) - Body ground Always 10 kΩ or higher
F76-12 (BCV+) - Body ground Always 10 kΩ or higher
F76-35 (BGND) - Body ground Always 10 kΩ or higher
F76-11 (BCB+) - Body ground Always 10 kΩ or higher




OK

2.CHECK PARKING ASSIST ECU (BCB+, BGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU (BCB+, BGND)
a.
U166326E02
1.302,1.146 1.385,1.427 1.385,1.427 1.563,1.427 true 1.333,0.979 1.219,0.677 1.219,0.677 1.052,0.677 true 0.094,0.063 0.271,0.24 0.177,0.177 10 false *a 0.604,0.594 1.01,0.854 0.406,0.26 10 false BCB+ 1.552,0.542 1.854,0.75 0.302,0.208 10 false F76 1.615,1.344 2.073,1.583 0.458,0.24 10 false BGND

Reconnect the F75 and F76 parking assist ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F76-35 (BGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F76-11 (BCB+) - F76-35 (BGND) Engine switch on (IG), front and side monitor main switch assembly on 5.5 to 7.05 V



Text in Illustration
*a Component with harness connected
(Parking Assist ECU)


OK

3.CHECK FRONT TELEVISION CAMERA ASSEMBLY (BCV+, BGND)

NG

3.CHECK FRONT TELEVISION CAMERA ASSEMBLY (BCV+, BGND)
a.

Reconnect the A55 front television camera assembly connector.

E349797E02
0.792,0.521 1.281,0.792 0.49,0.271 0.667,0.969 0.615,0.729 0.615,0.729 0.51,0.729 true 0.865,1.344 0.75,1.344 0.75,1.344 0.688,1.115 true 3.844,2.24 3.698,2.24 3.698,2.24 3.625,1.615 true 4.271,2 4.052,2 4.052,2 3.729,1.563 true 6.667,1.979 6.406,1.979 6.406,1.979 6.073,1.417 true 6.281,2.135 6.125,2.135 6.125,2.135 5.958,1.469 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 3.156,0.094 3.469,0.292 0.313,0.198 10 false *b 5.396,0.115 5.708,0.313 0.313,0.198 10 false *c 2.844,1.073 3.25,1.302 0.406,0.229 10 false GND 5.104,1.063 5.51,1.292 0.406,0.229 10 false GND 0.125,0.667 0.531,0.896 0.406,0.229 10 false BCV+ 0.917,1.271 1.323,1.5 0.406,0.229 10 false BGND 0.896,0.573 1.24,0.74 0.344,0.167 10 true F76 3.896,2.167 4.208,2.365 0.313,0.198 10 false *d 4.333,1.917 4.646,2.115 0.313,0.198 10 false *e 6.333,2.052 6.646,2.25 0.313,0.198 10 false *d 6.75,1.906 7.063,2.104 0.313,0.198 10 false *e

Text in Illustration
*a Component with harness connected
(Parking Assist ECU)
*b Waveform A
*c Waveform B *d Synchronization Signal
*e Video Waveform - -

HINT:
·

A waterproof connector is used for the front television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.

·

The video waveform changes according to the image sent by the front television camera assembly.




b.

Measure the resistance according to the value(s) in the table below.

OK:

Waveform is as shown in the illustration.


Item Content
Terminal No. (Symbol) F76-12 (BCV+) - F76-35 (BGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition
·

Waveform A: Engine switch on (IG), front and side monitor main switch assembly on and camera lens is not covered, displaying an image

·

Waveform B: Engine switch on (IG), front and side monitor main switch assembly on and camera lens is covered, blacking out the screen





OK

NG