Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › MULTI-TERRAIN MONITOR SYSTEM › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255515 MULTI-TERRAIN MONITOR SYSTEM C

PARK ASSIST / MONITORING  MULTI-TERRAIN MONITOR SYSTEM  C1621  Back Camera Power Supply Failure  


DESCRIPTION

These DTCs are stored if the parking assist ECU judges as a result of its self check that the signals or signal lines between the parking assist ECU and the rear television camera assembly are not normal.

DTC Code DTC Detection Condition Trouble Area
C1621 An open or short in the rear television camera signal circuit
·

Harness or connector

·

Rear television camera assembly

·

Parking assist ECU



WIRING DIAGRAM

E240924E21
5.563,0.469 6.198,0.75 0.635,0.281 10 false CB+ 5.302,0.385 5.479,0.552 0.177,0.167 10 false 14 5.552,1.281 6.135,1.51 0.583,0.229 10 false CGND 1.646,0.479 2.156,0.708 0.51,0.229 10 false CB+ 1.521,1.271 2.01,1.49 0.49,0.219 10 false CGND 5.385,1.75 5.74,1.958 0.354,0.208 10 false F76 0.885,1.604 1.333,1.823 0.448,0.219 10 false S30 0.885,1.771 2.448,2.198 1.563,0.427 10 false Rear Television Camera Assembly 5.385,1.917 6.906,2.135 1.521,0.219 10 false Parking Assist ECU 5.302,1.188 5.479,1.354 0.177,0.167 10 false 37 2.031,0.385 2.24,0.552 0.208,0.167 10 false 6 2.031,1.177 2.281,1.375 0.25,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the multi-display after the battery terminal disconnected, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the multi-terrain monitor system may be needed (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR TELEVISION CAMERA AND BODY GROUND)
a.

Disconnect the F76 parking assist ECU connector.


b.

Disconnect the S30 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F76-14 (CB+ - S30-6 (CB+) Always Below 1 Ω
F76-37 (CGND) - S30-5 (CGND) Always Below 1 Ω
F76-14 (CB+ or S30-6 (CB+) - Body ground Always 10 kΩ or higher
F76-37 (CGND) or S30-5 (CGND) - Body ground Always 10 kΩ or higher




OK

2.CHECK PARKING ASSIST ECU (CB+, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU (CB+, CGND)
a.
U166330E02
1.073,1.146 1.156,1.427 1.156,1.427 1.333,1.427 true 1.125,0.979 1.031,0.677 1.031,0.677 0.854,0.677 true 0.125,0.073 0.385,0.344 0.26,0.271 10 false *a 0.531,0.604 0.833,0.802 0.302,0.198 10 false CB+ 1.542,0.552 1.865,0.781 0.323,0.229 10 false F76 1.396,1.344 1.844,1.563 0.448,0.219 10 false CGND

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F76-37 (CGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F76-14 (CB+) - F76-37 (CGND) Engine switch on (IG) 5.5 to 7.05 V



Text in Illustration
*a Component with harness connected
(Parking Assist ECU)


OK

NG